192.168.0.100 Admin Login

Several well-known networking brands use 192.168.0.100 as their default IP address, most notably Netgear (for its wireless access point lineup), TRENDnet (across a wide range of its TEW-series access points and routers), D-Link, and Medion. ISP-supplied routers from manufacturers such as Huawei and ZTE also occasionally ship with 192.168.0.100 as their default gateway. This address sits inside the 192.168.0.0/24 private subnet — one of the most widely deployed Class C private ranges in home and small-office networking. Because it is a private IPv4 address, 192.168.0.100 is never routed over the public internet and is exclusively used for internal LAN communication. Only one device on your network should be assigned 192.168.0.100 at any given time to avoid an IP address conflict. Other commonly used default gateways in the same subnet include 192.168.0.1, 192.168.0.254, and 192.168.0.2.

How to Access 192.168.0.100

To reach your router or access point's admin panel, make sure your computer or mobile device is connected to the same network — either via Wi-Fi or an Ethernet cable. Then open any web browser (Chrome, Firefox, Edge, or Safari all work) and type http://192.168.0.100 directly into the address bar and press Enter. Do not type it into a search engine — paste it into the address bar only.

If the login page loads, you will be prompted for a username and password. For most devices that use 192.168.0.100, the default credentials are:

• Netgear access points (WAC120, WAC124, WAC730, WNDAP360, WNDAP620, WN604, WNAP320, etc.): Username admin / Password password
• TRENDnet TEW-series access points (TEW-610APB, TEW-637AP, TEW-638APB, TEW-651BR, TEW-692GR, and many others): Username admin / Password admin
• D-Link DSM-G600: Username admin / Password (blank — leave empty)
• Medion MD 95038: Username admin / Password admin

If none of these work, check the label on the bottom or back of your device — manufacturers often print the unique default credentials there. Once logged in, you can manage wireless settings, security configurations, firmware updates, DHCP reservations, port forwarding, and much more.

If You Can't Access 192.168.0.100

If typing http://192.168.0.100 into your browser returns an error or a blank page, there are a few likely causes to investigate:

1. Your device is not on the 192.168.0.x subnet. The most common reason 192.168.0.100 is unreachable is that your computer's gateway is on a different subnet (e.g., 192.168.1.x). On Windows, open Command Prompt and run ipconfig /all. Look for the Default Gateway field. On macOS or Linux, run ip route or check System Preferences > Network. If the gateway shown is different from 192.168.0.100, visit our guide to find your correct router IP address.
2. The IP has been changed. A previous administrator may have changed the default gateway away from 192.168.0.100. In this case, use the ipconfig /all result to find the current gateway and navigate to that address instead.
3. You are using a Netgear AP in DHCP client mode. Netgear access points like the WAC series default to 192.168.0.100 only when no DHCP server is present. Once connected to a router, the AP is assigned a dynamic IP. Use the Netgear Insight app, Windows File Explorer > Network, or your router's DHCP client list to find the AP's current IP.
4. Browser or cache issue. Try clearing your browser cache or using a private/incognito window. Also ensure you are not accidentally typing the address into a search bar.
5. Firewall or security software. Temporarily disable any firewall or VPN software that may be blocking local network access.

Router Brands That Use 192.168.0.100

Unlike more universal gateway addresses such as 192.168.0.1 or 192.168.1.1, the address 192.168.0.100 is used by a more specific set of devices. Here is a breakdown of the confirmed brands and their notable models:

Netgear

Netgear is the most prominent brand associated with 192.168.0.100. Netgear officially documents this as the default IP address for its wireless access point (AP) product line. When a Netgear AP has never been configured or has been reset to factory defaults, it will respond at 192.168.0.100. Models confirmed to use this address include the WAC120, WAC124, WAC730, WN203, WN604, WNAP320, WND930, WNDAP360, WNDAP620, and WNDAP660. Note that once the AP is connected to a network with a DHCP server (your main router), it will be assigned a new dynamic IP — 192.168.0.100 is only guaranteed when the AP is in standalone/factory-default mode.

TRENDnet

TRENDnet uses 192.168.0.100 across a very large number of its TEW-series wireless access points and routers. Confirmed models include the TEW-610APB, TEW-611BRP, TEW-630APB, TEW-631BRP, TEW-632BRP, TEW-633GR, TEW-634GRU, TEW-635BRM, TEW-636APB, TEW-637AP, TEW-637APv2, TEW-638APB, TEW-638APBv2, TEW-651BR, TEW-652BRP, TEW-653AP, TEW-671BR, TEW-672GR, TEW-691GR, TEW-692GR, TEW-731BR, TEW-811DRU, TEW-812DRU, TEW-818DRU, TEW-823DRU, and many more. The default login for TRENDnet devices at this IP is typically admin / admin.

D-Link

D-Link uses 192.168.0.100 on select models, including the DSM-G600-A1 network storage router. The default username is admin with no password required on first login.

Medion

Medion, a European electronics brand, uses 192.168.0.100 on its MD 95038 router model. Default credentials are admin / admin.

Huawei & ZTE (ISP Routers)

Certain ISP-supplied gateway devices from Huawei and ZTE are also known to use 192.168.0.100 as their default LAN IP, particularly in markets where ISPs pre-configure their own firmware. If your router was provided by your internet service provider, check the label on the device or contact your ISP for the correct default credentials.

Factory Reset Procedures for Devices Using 192.168.0.100

If you have forgotten your admin password and cannot log in at 192.168.0.100, a factory reset will restore the device to its default settings — including the default IP address and credentials. Warning: A factory reset erases all custom configurations, including your Wi-Fi name (SSID), password, port forwarding rules, and any other changes you have made.

Netgear Access Points (WAC/WNDAP Series)

1. Ensure the device is powered on. Wait for the power LED to be solid.
2. Locate the Factory Reset or Reset button — typically a small pinhole on the rear or bottom panel.
3. Insert a straightened paperclip or pin and hold the button for 10 seconds until the LEDs flash or the device reboots.
4. Release the button and wait approximately 2 minutes for the device to fully restart.
5. The device will now respond at 192.168.0.100 with the default credentials: admin / password.

TRENDnet TEW-Series Devices

1. Make sure the device is powered on.
2. Find the Reset pinhole button on the back or bottom of the unit.
3. Use a pin or paperclip to press and hold the Reset button for 15 seconds.
4. Release and allow the device to reboot (approximately 60–90 seconds).
5. Once rebooted, navigate to http://192.168.0.100 and log in with admin / admin.

D-Link DSM-G600

1. With the unit powered on, insert a paperclip into the Reset hole on the back panel.
2. Hold for 10 seconds, then release.
3. Wait for the device to reboot and then access it at http://192.168.0.100 using username admin and a blank password.

Changing Your Password at 192.168.0.100

Keeping the default password on any device accessible at 192.168.0.100 is a significant security risk. Anyone connected to your local network could potentially access your router or access point's admin panel using the well-known default credentials. Here's how to change it:

1. Log in to your admin panel by navigating to http://192.168.0.100 and entering your current credentials.
2. Look for a section labeled Administration, Management, System, or Advanced Settings — the exact label depends on your brand.
3. Find the Change Password or Admin Password option.
4. Enter your current password, then type your new password twice to confirm.
5. Click Save or Apply.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Avoid using easily guessable information like your address or birthday. Store the new password somewhere safe — if you forget it, you will need to perform a factory reset to regain access to 192.168.0.100.

Router Username and Password List

What Is 192.168.0.100 as a Private IP Address?

192.168.0.100 is a Class C private IPv4 address, defined under RFC 1918. This means it belongs to the reserved private address space (192.168.0.0 – 192.168.255.255) and is never routed on the public internet. It can only be reached by devices on the same local area network (LAN).

In the context of the 192.168.0.0/24 subnet, the address 192.168.0.100 is one of 254 usable host addresses (192.168.0.1 through 192.168.0.254). When a router or access point uses 192.168.0.100 as its default gateway, all other devices on the network receive addresses from the same range. For example:

• Your laptop might be assigned 192.168.0.101
• Your smartphone might receive 192.168.0.102
• A smart TV or gaming console might get 192.168.0.103

These addresses are dynamically assigned by the router's built-in DHCP server, which hands out IPs from a configured pool. The router itself — at 192.168.0.100 — acts as the gateway through which all internet-bound traffic flows. It also performs Network Address Translation (NAT), allowing all your private devices to share a single public IP address assigned by your ISP.

Because 192.168.0.100 is a private address, it is completely safe to access from within your home or office network. It is not visible to the outside world and cannot be directly targeted by external attackers — though securing your admin panel with a strong password remains essential to protect against threats from within the local network.

Related IP Addresses in the 192.168.0.x Subnet

The 192.168.0.0/24 subnet is one of the most commonly used private network ranges in the world. Several addresses within this range are frequently used as default gateways by various router manufacturers. If 192.168.0.100 is not your router's IP, one of the following may be:

• 192.168.0.1 — The most common default gateway in this subnet, used by Netgear (home routers), TP-Link, D-Link, and many others.
• 192.168.0.254 — Used by some TP-Link and BT Home Hub models as their default gateway.
• 192.168.0.2 — Occasionally used as a secondary router or access point IP in dual-router setups.
• 192.168.0.10 — Sometimes assigned to managed switches or secondary network devices.
• 192.168.0.100 — This page's IP, used primarily by Netgear APs, TRENDnet TEW-series devices, D-Link DSM-G600, and Medion routers.

If you are unsure which IP your router uses, the fastest way to find out is to run ipconfig /all on Windows (or ip route on Linux/macOS) and look at the Default Gateway field. That value is the IP address you should type into your browser to access your router's admin panel.

Frequently Asked Questions About 192.168.0.100

What devices use 192.168.0.100 as their default IP?

The most notable brands confirmed to use 192.168.0.100 as a default IP are Netgear (wireless access points such as the WAC120, WAC124, WNDAP360, and WNDAP620), TRENDnet (a large range of TEW-series access points and routers including the TEW-610APB, TEW-637AP, TEW-692GR, and TEW-818DRU), D-Link (DSM-G600), Medion (MD 95038), and some ISP-supplied Huawei and ZTE gateway devices.

Why can't I reach 192.168.0.100 even though my router uses it?

The most common reason is that your computer is connected to a different subnet. If your PC's IP address starts with 192.168.1.x, it cannot directly reach 192.168.0.100. You may need to connect directly to the device via Ethernet, or temporarily set your computer's IP to a static address in the 192.168.0.x range (e.g., 192.168.0.50) to access the admin panel. For Netgear APs specifically, remember that 192.168.0.100 is only the factory-default IP — once the AP joins a network with a DHCP server, it will be assigned a different address.

Is 192.168.0.100 the same as 192.168.0.1?

No. While both are private Class C addresses in the same /24 subnet, they are distinct IP addresses assigned to different devices. 192.168.0.1 is the more common default gateway used by brands like Netgear (home routers), TP-Link, and D-Link. The address 192.168.0.100 is specifically used by Netgear access points, TRENDnet TEW-series devices, and a handful of other models. Having both on the same network is perfectly valid as long as they are assigned to different devices.

What is the default username and password for 192.168.0.100?

It depends on your device brand. For Netgear access points, use admin / password. For TRENDnet TEW-series devices, use admin / admin. For the D-Link DSM-G600, use admin with a blank password. For Medion MD 95038, use admin / admin. Always check the label on the bottom or back of your device, as some units ship with unique printed credentials.

Can two devices on my network both use 192.168.0.100?

No. Assigning 192.168.0.100 to more than one device on the same network will cause an IP address conflict, resulting in connectivity issues for both devices. If you have a TRENDnet router and a Netgear access point on the same network, you must change one of them to a different IP address through its admin panel to resolve the conflict.

How do I change the IP address of my device from 192.168.0.100?

Log in to the admin panel at http://192.168.0.100, then navigate to the LAN Settings or Network Settings section. Enter a new IP address in the same subnet (e.g., 192.168.0.101) and click Save. The device will reboot and will be accessible at the new address going forward. Only change the IP if you are experiencing a conflict or have a specific networking requirement.