192.168.9.1 Admin Login

192.168.9.1 is a Class C private IPv4 address used as the default gateway on a select group of routers, wireless access points, and mobile broadband devices. Unlike the more widespread 192.168.1.1 or 192.168.0.1, this address is associated with specific brands and device categories — most notably Hikvision wireless routers (AX1800, AX3000, AC1200, and Router 6000 series), GL.iNet routers (as the default guest network gateway), and certain carrier-branded 4G LTE and 5G CPE mobile broadband devices from manufacturers such as Huawei. If your router's admin panel is at 192.168.9.1, you are most likely using one of these devices. Only one device on your local network should ever be assigned 192.168.9.1 to avoid an IP address conflict.

How to Access 192.168.9.1

To reach your router's admin panel at 192.168.9.1, open any web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.9.1 directly into the address bar, then press Enter. Do not type it into a search engine, as that will return search results rather than your router's login page. If you are using a Hikvision router, you can also reach the admin panel by typing http://hikrouter.net into the address bar — this is the official domain alias Hikvision provides for all its AX and AC series routers.

Once the login page loads, you will be prompted to enter your admin username and password. For most devices using 192.168.9.1, the default credentials are:

• Hikvision routers: No default password — you are required to create one during the initial activation process.
• GL.iNet routers (guest network): Managed through the main admin panel at 192.168.8.1; the guest network gateway 192.168.9.1 does not have a separate login page.
• Huawei 4G/5G CPE devices: Username: admin — Password: printed on the device label (bottom or back sticker).
• Generic fallback credentials: Username: admin / Password: admin, password, or 123456.

Always check the sticker on the bottom or back of your device first, as many modern routers no longer ship with a universal default password and instead use a unique one printed on the label.

If You Can't Access 192.168.9.1

If typing http://192.168.9.1 into your browser does not load a login page, work through the following checks before assuming the address is wrong:

• Confirm your connection: Make sure your computer, phone, or tablet is connected to the same network as the router — either via a Wi-Fi connection to the router's SSID or via an Ethernet cable plugged into one of the router's LAN ports. You cannot reach 192.168.9.1 from a different network.
• Verify your gateway address: On Windows, open Command Prompt (Start > type cmd > Enter) and run ipconfig. Look for the Default Gateway field. On macOS or Linux, run netstat -nr or check System Preferences > Network. If the gateway shown is not 192.168.9.1, your router uses a different IP — check our guide to find your router IP address.
• Try HTTPS: Some newer Hikvision routers enforce a secure connection. Try https://192.168.9.1 (with the 's') if the plain HTTP version fails.
• Disable VPN or proxy: Active VPN connections or browser proxy settings can redirect your traffic and prevent you from reaching local addresses like 192.168.9.1. Temporarily disable any VPN before trying again.
• Clear browser cache: A cached redirect or error page can block the login screen. Try opening an incognito/private window or a different browser entirely.
• Check for IP conflicts: If another device on your network has been manually assigned 192.168.9.1, a conflict will prevent the router from responding. Check your connected devices' IP settings.

If none of the above resolves the issue, the router's default gateway may have been changed from 192.168.9.1 to another address. In that case, a factory reset (see below) will restore it.

Router Brands That Use 192.168.9.1

Unlike the most common gateway addresses, 192.168.9.1 is used by a specific set of brands and device types. Here is a breakdown of the confirmed brands and how they use this address:

Hikvision

Hikvision — best known for its security cameras and NVR systems — has expanded into the consumer and SMB Wi-Fi router market with a full lineup of wireless routers. Every Hikvision router model uses 192.168.9.1 as its default LAN gateway address. Confirmed models include:

• Hikvision Router AX3000 (DS-3WR12C and variants)
• Hikvision Router AX1800
• Hikvision Router AC1200 (4-port)
• Hikvision Router 6000

All Hikvision routers also support the login alias http://hikrouter.net in addition to http://192.168.9.1. The default Wi-Fi SSID is printed as HIKVISION_XXXX on the device label. Importantly, Hikvision does not ship its routers with a pre-set admin password — you must create one during the first-time activation wizard.

GL.iNet

GL.iNet travel and portable routers use 192.168.9.1 as the default gateway for their Guest Network (since firmware v4.5, the guest network settings are separated from the main LAN). The primary admin panel for GL.iNet routers is located at 192.168.8.1, while the guest network subnet operates on 192.168.9.0/24 with 192.168.9.1 as its gateway. If you see 192.168.9.1 on a GL.iNet device, you are connected to the guest Wi-Fi network, not the main network.

Huawei (Carrier-Branded 4G/5G CPE Devices)

Huawei 4G LTE and 5G CPE (Customer Premises Equipment) routers — particularly those distributed by mobile carriers — may use 192.168.9.1 as their management address in certain firmware configurations. For example, some Huawei 5G CPE units distributed by Three UK have been reported to use 192.168.9.1 as their gateway (shifted from the more common 192.168.8.1 used by standard Huawei CPE devices). Always check the label on your specific Huawei device to confirm the correct admin IP.

Changing Your Router's Password at 192.168.9.1

Keeping a strong, unique admin password is one of the most important steps you can take to secure your home or office network. If your router's admin panel is at 192.168.9.1, here is how to update your password:

1. Open your browser and navigate to http://192.168.9.1 (or http://hikrouter.net for Hikvision routers).
2. Log in with your current admin credentials.
3. For Hikvision routers: Go to System > Account Management > Change Password. Enter your current password, then your new password twice to confirm.
4. For Huawei CPE devices: Navigate to Settings > Device > Modify Password.
5. For GL.iNet routers: Log in at 192.168.8.1, then go to System > Admin Password.

Choose a password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Avoid using the same password as your Wi-Fi network. Once changed, store your new password in a secure password manager so you do not get locked out.

Router Username and Password List

How to Factory Reset a Router Using 192.168.9.1

If you have forgotten your admin password or your router is behaving unexpectedly, a factory reset will restore all settings — including the gateway address 192.168.9.1 — to their original defaults. The exact procedure depends on your device:

Hikvision Router Factory Reset

1. Make sure the router is powered on and the indicator light is active.
2. Locate the RESET button on the back or bottom of the router (it is recessed in a small pinhole).
3. Use a straightened paperclip or a SIM ejector pin to press and hold the RESET button for 8 seconds.
4. Release the button when the indicator light changes behavior (flashes or turns off and back on).
5. The router will reboot automatically. Once it restarts, it will be back to factory defaults — you will need to go through the activation wizard again at http://192.168.9.1 or http://hikrouter.net and create a new admin password.

Huawei 4G/5G CPE Factory Reset

1. Ensure the device is powered on.
2. Find the RESET (or RST) pinhole on the device body.
3. Press and hold the reset button with a pin or paperclip for 5–10 seconds.
4. Wait for the indicator lights to change and the device to reboot automatically.
5. Reconnect to the device's Wi-Fi network using the default SSID and password from the label, then access http://192.168.9.1 to reconfigure.

GL.iNet Router Factory Reset

1. Power on the router and wait for it to fully boot.
2. Press and hold the reset button for 10 seconds until the LED flashes.
3. The router will reboot. The guest network gateway will return to 192.168.9.1 and the main admin panel will be accessible again at 192.168.8.1.

Important: A factory reset erases all custom settings — your Wi-Fi name, Wi-Fi password, port forwarding rules, and any other configurations. Only perform a reset if you have no other way to regain access.

What Is 192.168.9.1? Understanding Private IP Addresses

192.168.9.1 is a private IPv4 address belonging to the Class C private address range defined by RFC 1918. The full Class C private range spans from 192.168.0.0 to 192.168.255.255, and addresses within this range are never routed over the public internet — they exist exclusively within local networks (LANs).

When your router uses 192.168.9.1 as its gateway, it also defines the subnet that all connected devices will belong to: 192.168.9.0/24. This means your router's built-in DHCP server will automatically assign IP addresses in the range of 192.168.9.2 through 192.168.9.254 to every device that connects to your network. For example:

• Your laptop might receive 192.168.9.2
• Your smartphone might receive 192.168.9.3
• Your smart TV might receive 192.168.9.4
• Your printer might receive 192.168.9.5

The router at 192.168.9.1 acts as the traffic controller for all of these devices — it receives data requests from them, forwards those requests to the internet via your ISP's connection, and routes the responses back to the correct device. Without the gateway at 192.168.9.1, none of your devices would be able to communicate with the outside world.

Because 192.168.9.1 is a private address, it is completely invisible to the public internet. Your ISP and external websites only ever see your router's public IP address — the one assigned to your WAN port by your ISP. The 192.168.9.1 address is strictly internal to your home or office network.

Related IP Addresses in the 192.168.9.x Subnet

If you are working within a network that uses 192.168.9.1 as its gateway, the following IP addresses in the same 192.168.9.0/24 subnet are relevant to know:

• 192.168.9.0 — The network address for the subnet. This address is never assigned to a device.
• 192.168.9.1 — The default gateway (your router's LAN IP address).
• 192.168.9.2 – 192.168.9.254 — The usable host range. Your DHCP server assigns addresses from this pool to connected devices.
• 192.168.9.255 — The broadcast address for the subnet. Packets sent to this address are delivered to all devices on the network.

Other commonly used private gateway addresses that you may encounter on other networks include 192.168.1.1, 192.168.0.1, 192.168.8.1, 192.168.10.1, 192.168.1.254, 192.168.100.1, 192.168.2.1, and 10.0.0.1. Each of these belongs to a different subnet and is used by different router brands and ISPs.

Frequently Asked Questions About 192.168.9.1

Which routers use 192.168.9.1 as their default gateway?

The primary brands confirmed to use 192.168.9.1 as their default gateway are Hikvision (all current wireless router models including the AX3000, AX1800, AC1200, and Router 6000), GL.iNet (as the guest network gateway on firmware v4.5 and later), and certain carrier-branded Huawei 4G/5G CPE devices. If you have one of these devices and see 192.168.9.1 as your gateway, this is expected behavior.

Why does my Hikvision router use 192.168.9.1 instead of 192.168.1.1?

Hikvision chose 192.168.9.1 as the default gateway for its router lineup to reduce the likelihood of IP conflicts with other devices on your network — particularly if you are connecting the Hikvision router behind another router that already uses the more common 192.168.1.1 or 192.168.0.1. You can also access your Hikvision router's admin panel using the domain alias http://hikrouter.net as an alternative to typing 192.168.9.1 directly.

Can I change 192.168.9.1 to a different IP address?

Yes. Once you log in to your router's admin panel at 192.168.9.1, you can navigate to the LAN settings section and change the gateway IP to any other valid private address (such as 192.168.1.1 or 192.168.0.1). After saving the change, your router will reboot and you will need to use the new IP address to access the admin panel going forward. Note that changing the gateway IP will also shift the DHCP range your router assigns to connected devices.

What is the default username and password for 192.168.9.1?

This depends on your device. Hikvision routers do not have a pre-set default password — you create one during the initial setup wizard. Huawei CPE devices typically use admin as the username with a unique password printed on the device label. GL.iNet routers are managed through 192.168.8.1, not 192.168.9.1 directly. For other devices, try admin / admin, admin / password, or admin / 123456 as common fallback credentials.

Is 192.168.9.1 safe to use as a gateway address?

Yes, 192.168.9.1 is a completely standard and safe private IP address. Like all addresses in the 192.168.x.x range, it is non-routable on the public internet, meaning it cannot be accessed by anyone outside your local network. The security of your network depends not on the gateway address itself, but on the strength of your admin password and Wi-Fi password — both of which you should change from their defaults as soon as possible after setting up your router.

My 192.168.9.1 login page is not loading — what should I do?

First, confirm that your device is connected to the correct network (the one broadcast by the router using 192.168.9.1 as its gateway). Then open a command prompt and run ipconfig (Windows) or check your network settings (Mac/iOS/Android) to verify that your Default Gateway is indeed 192.168.9.1. If it shows a different address, you are connected to the wrong network or your router's IP has been changed. If the gateway is correct but the page still won't load, try a different browser, disable any VPN, or attempt https://192.168.9.1 instead of the HTTP version.