192.168.49.1 Admin Login

Unlike most router default gateways such as 192.168.1.254 or 192.168.0.1, the IP address 192.168.49.1 is not a standard default gateway used by traditional home routers. Instead, it is a Class C private IPv4 address that appears in three very specific and well-documented scenarios: as the hardcoded Android Wi-Fi Direct group owner address, as the default admin IP for fake AnyCast and Q2 Wi-Fi streaming dongles, and as the gateway assigned during Android USB tethering and mobile hotspot sessions. If you are seeing 192.168.49.1 as your gateway, one of these three situations almost certainly applies to you. Understanding which one will help you take the right next steps — whether that's configuring a streaming dongle, troubleshooting a tethered connection, or managing a Wi-Fi Direct peer-to-peer session.

What Devices Use 192.168.49.1?

Because 192.168.49.1 is not a conventional router IP, it is important to understand exactly which devices and platforms assign it. Here is a breakdown of the three primary sources:

• Android Wi-Fi Direct (All Android Devices): According to the Android Open Source Project (AOSP) source code, 192.168.49.1 is the hardcoded, static IP address assigned to the Wi-Fi Direct group owner on every Android device. When two Android phones, tablets, or Android-powered devices establish a Wi-Fi Direct (P2P) connection, the device acting as the group owner is always assigned 192.168.49.1. This is not configurable by the user — it is baked into the Android platform itself. Devices from Samsung, Google (Pixel), OnePlus, Xiaomi, Motorola, Sony, and virtually every other Android manufacturer will use this IP when acting as a Wi-Fi Direct group owner.
• Fake AnyCast & Q2 Wi-Fi Streaming Dongles: A range of counterfeit or third-party Miracast/DLNA streaming dongles — often sold under the AnyCast name or as the Q2 Wi-Fi Display Dongle — use 192.168.49.1 as their default admin gateway. Note that the genuine AnyCast dongle uses 192.168.203.1 as its default IP. If your dongle's welcome screen shows 192.168.49.1, you have a third-party or clone device. You can still configure it using this IP address.
• Android USB Tethering & Mobile Hotspot: When you share your Android phone's mobile data connection via USB tethering or Wi-Fi hotspot, your phone acts as a gateway and may assign 192.168.49.1 as the default gateway to connected devices. This is particularly common with certain Android versions and carrier configurations.

How to Access 192.168.49.1

If you need to access the admin or settings page at 192.168.49.1 — most commonly for configuring a fake AnyCast or Q2 streaming dongle — follow these steps:

1. Connect to the device's Wi-Fi network first. Power on your streaming dongle and connect it to your TV via HDMI. The dongle will broadcast its own Wi-Fi network (SSID). On your phone or laptop, disconnect from your home Wi-Fi and connect to the dongle's Wi-Fi network. The SSID name and password are displayed on your TV screen.
2. Open your web browser. Once connected to the dongle's Wi-Fi, open any browser (Chrome, Firefox, Safari, Edge) on your phone or computer.
3. Type the IP address into the address bar. Enter http://192.168.49.1 directly into the browser's address bar — not the search bar. Press Enter.
4. The settings page will load. For most fake AnyCast and Q2 dongles, no username or password is required. The settings panel opens directly, allowing you to scan for and connect to your home Wi-Fi network.
5. Connect the dongle to your home Wi-Fi. Look for an option labeled Internet, Scan, or Wi-Fi Settings. Select your home network from the list, enter your Wi-Fi password, and save. The dongle will now relay your home internet to your TV screen.

If 192.168.49.1 does not load in your browser, make sure you are still connected to the dongle's Wi-Fi network and not your home router. Also confirm you are typing the address into the URL/address bar, not a search engine field.

192.168.49.1 and Android Wi-Fi Direct — What You Need to Know

If you are a developer, network administrator, or technically curious user who encountered 192.168.49.1 in a Wi-Fi Direct context, here is what is happening under the hood. Android's Wi-Fi Direct implementation — also known as Wi-Fi P2P — is defined in the Android Open Source Project. When a Wi-Fi Direct group is formed between two or more Android devices, one device is elected as the Group Owner (GO). The Group Owner acts like a mini access point and runs a DHCP server to assign IP addresses to the other devices (P2P clients) in the group.

The Group Owner's IP address is defined as a constant in Android's source code: SERVER_ADDRESS = "192.168.49.1". This value is final and static — it does not change between Android versions, manufacturers, or device models. Every Android device that becomes a Wi-Fi Direct group owner will always be reachable at 192.168.49.1 by the other devices in the group. The connected client devices receive addresses in the 192.168.49.x range (e.g., 192.168.49.2, 192.168.49.3, etc.) from the group owner's DHCP server.

This is why you may see 192.168.49.1 appear as your default gateway when using apps that leverage Wi-Fi Direct for local data transfer, such as file-sharing apps, screen mirroring tools, or local multiplayer games. It is also why Amazon's Fire TV devices and Intel's Wi-Fi Direct implementations may surface this IP — they interact with Android's Wi-Fi Direct stack.

If You Can't Access 192.168.49.1

There are several reasons why typing http://192.168.49.1 into your browser might not work. Here is how to diagnose and fix each one:

• You are connected to the wrong Wi-Fi network. This is the most common issue. To reach 192.168.49.1, your device must be on the same network as the device hosting that IP — whether that is a streaming dongle's hotspot or an Android Wi-Fi Direct group. Check your Wi-Fi connection and make sure you are connected to the correct network before trying again.
• You typed the address into a search bar instead of the address bar. Browsers like Chrome will search Google if you type an IP address into the search bar. Make sure you are entering 192.168.49.1 into the URL/address bar at the very top of the browser window.
• The dongle's IP has been changed. If someone previously configured the dongle and changed its default IP, 192.168.49.1 will no longer work. Try performing a factory reset on the dongle (usually a small reset button held for 10 seconds) to restore the default IP.
• A firewall or antivirus is blocking the connection. Security software on your PC or phone may block access to local network admin pages. Temporarily disable your firewall or antivirus and try again.
• 192.168.49.1 is not your actual gateway. If you are trying to access a traditional router and ended up on this page, 192.168.49.1 is likely not your router's IP. Open Command Prompt (Windows: Start > cmd > ipconfig /all) or Terminal (Mac/Linux: netstat -nr | grep default) and look for the Default Gateway value. Common router gateways include 192.168.0.1, 192.168.1.254, 192.168.8.1, and 10.0.0.1.

Setting Up Your Fake AnyCast / Q2 Dongle via 192.168.49.1 — Step-by-Step

If you have purchased a third-party Miracast or DLNA streaming dongle that displays 192.168.49.1 on your TV screen, follow this complete setup guide:

1. Physical Setup: Attach the antenna to your dongle (if included). Plug the dongle into an available HDMI port on your TV. Connect the USB power cable to a USB port on your TV or to a 5V/1A USB power adapter (not always included in the box). Switch your TV to the correct HDMI input source.
2. Welcome Screen: After powering on, your TV should display a welcome screen showing the dongle's Wi-Fi SSID and password. Note these down.
3. Connect Your Phone or Laptop to the Dongle's Wi-Fi: On your phone or laptop, go to Wi-Fi settings. Disconnect from your home network and connect to the SSID shown on your TV screen. Enter the password displayed on the TV.
4. Open the Admin Page: Open your browser and navigate to http://192.168.49.1. The dongle's settings page will load without requiring a login.
5. Connect the Dongle to Your Home Wi-Fi: In the settings page, find the Wi-Fi or Internet section. Tap Scan to discover nearby networks. Select your home Wi-Fi network and enter your password. Save the settings.
6. Reconnect Your Device to Home Wi-Fi: Once the dongle connects to your home network, reconnect your phone or laptop to your home Wi-Fi as well. You can now use Miracast, DLNA, or AirPlay (depending on your dongle's capabilities) to mirror your screen to the TV.

Tip: If your dongle overheats frequently, has unstable mirroring, or drops Wi-Fi often, these are signs of a lower-quality clone device. The genuine AnyCast dongle uses 192.168.203.1 as its admin IP and offers more stable performance.

Changing the Password and Securing Your 192.168.49.1 Network

Whether you are using a streaming dongle or managing an Android Wi-Fi Direct session through 192.168.49.1, network security still matters. Here are the key steps to keep your connection secure:

• Change the default Wi-Fi password on your dongle. After accessing the settings page at 192.168.49.1, look for a Wi-Fi or Security section. Change the default SSID name and password to something unique and strong. Use a mix of uppercase and lowercase letters, numbers, and symbols. Avoid using your name, address, or any easily guessable information.
• Limit who can connect. Some dongles allow you to set a maximum number of connected devices or enable MAC address filtering. Use these features to prevent unauthorized devices from connecting to your dongle's network.
• Keep firmware updated. If your dongle supports firmware updates (accessible through the 192.168.49.1 settings page), apply them. Updates often include security patches and performance improvements.
• For Android Wi-Fi Direct: Wi-Fi Direct connections require explicit acceptance on both devices, which provides a built-in layer of security. Always verify the device you are connecting to before accepting a Wi-Fi Direct invitation.

Router Username and Password List

What is 192.168.49.1 as a Private IP Address?

192.168.49.1 is a Class C private IPv4 address belonging to the 192.168.49.0/24 subnet. The entire 192.168.0.0/16 block — which includes 192.168.49.1 — is reserved for private use by RFC 1918. This means it can never be routed on the public internet and is exclusively used for communication within local area networks (LANs).

As the first usable host address in the 192.168.49.0/24 subnet, 192.168.49.1 is a natural choice for a gateway or access point address. The subnet supports up to 254 usable host addresses (192.168.49.1 through 192.168.49.254), making it well-suited for small to medium-sized local networks. When a device at 192.168.49.1 acts as a DHCP server — as Android does in Wi-Fi Direct mode — it assigns addresses from this pool to connected clients:

• The first connected client receives 192.168.49.2
• The second connected client receives 192.168.49.3
• And so on, up to 192.168.49.254

Because 192.168.49.1 is a private address, devices using it cannot be accessed from the internet. All communication stays within the local network. If the device at 192.168.49.1 needs to provide internet access to connected clients (as a mobile hotspot does), it uses Network Address Translation (NAT) to forward traffic between the private network and the public internet via the device's cellular or broadband connection.

Other commonly used private IPs in nearby subnets include 192.168.0.1, 192.168.2.1, 192.168.8.1, and 192.168.10.1. For larger private networks, 10.0.0.1 is a common Class A alternative.

Frequently Asked Questions About 192.168.49.1

Why is my gateway showing 192.168.49.1 when I'm not using a dongle?

If you see 192.168.49.1 as your default gateway without a streaming dongle connected, you are most likely connected to an Android device acting as a Wi-Fi Direct group owner or a mobile hotspot. Check if your connection is going through another phone or Android device rather than your home router. You can verify your actual gateway by running ipconfig /all on Windows or netstat -nr on Mac/Linux.

Is 192.168.49.1 safe to access?

Yes. 192.168.49.1 is a private IP address and is only accessible from within your local network. It cannot be reached from the internet. Accessing it via your browser simply opens the admin or settings page of whichever local device is hosting that IP — typically a streaming dongle or an Android Wi-Fi Direct group owner.

What is the default username and password for 192.168.49.1?

For fake AnyCast and Q2 streaming dongles that use 192.168.49.1, no login credentials are typically required — the settings page opens directly in your browser. For Android Wi-Fi Direct, there is no admin page at 192.168.49.1; the IP is simply the group owner's network address. If you are trying to access a router that has been manually configured to use 192.168.49.1, check the label on the back or bottom of the device for default credentials.

Can I change the IP address from 192.168.49.1 to something else?

For streaming dongles, yes — you can usually change the LAN IP from within the settings page at 192.168.49.1 under a section like LAN Settings or Network Settings. For Android Wi-Fi Direct, no — the 192.168.49.1 address is hardcoded in the Android source code and cannot be changed without modifying the OS itself.

My fake AnyCast dongle shows 192.168.49.1 but the page won't load. What should I do?

First, confirm your phone or laptop is connected to the dongle's Wi-Fi network (not your home router). Then open your browser and type http://192.168.49.1 into the address bar — not the search bar. If it still fails, try a factory reset on the dongle by holding the reset button for 10 seconds. This restores the default IP and settings.

What other IP addresses are related to 192.168.49.1?

192.168.49.1 is the gateway address of the 192.168.49.0/24 subnet. Related addresses in the same subnet include 192.168.49.2 through 192.168.49.254, which are assigned to client devices. Other commonly used private gateways in the broader 192.168.x.x range include 192.168.0.1, 192.168.2.1, 192.168.100.1, and 192.168.1.254.