192.168.200.1 Admin Login

The IP address 192.168.200.1 is a private Class C IPv4 address used as the default gateway in select local area networks. It is most notably associated with Bitmain (specifically the AntRouter R1-LTC and related mining router devices), Westell (including the VersaLink 327W DSL gateway), and MQmaker (the WiTi Board). While less common than addresses like 192.168.1.1 or 192.168.0.1, the 192.168.200.1 address is a fully valid and functional default router IP used in both consumer and specialized networking hardware. Because it sits in the 192.168.200.x subnet — a less frequently assigned private range — it is sometimes preferred in enterprise VLAN configurations and segmented networks to avoid conflicts with more common subnets. Only one device on your local network should be assigned 192.168.200.1 at any given time to prevent IP address conflicts.

How to Access 192.168.200.1

To reach your router's admin panel, open any web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.200.1 directly into the address bar. Do not type it into a search engine, as that will return search results rather than your router's login page. Press Enter and you should be presented with a login prompt asking for a username and password.

Before you attempt to log in, make sure your device is connected to the same network as the router — either via a Wi-Fi connection or a physical Ethernet (LAN) cable. If you are using a Bitmain AntRouter, the default credentials are root / root. For a Westell VersaLink 327W, try admin / password. For MQmaker WiTi Board devices, the login is typically admin / admin or root / root. Once logged in, you can manage your Wi-Fi SSID, password, DHCP settings, port forwarding rules, firmware updates, and more.

Because 192.168.200.1 is a private IPv4 address, it is only reachable from within your local network. You cannot access it from outside your home or office — this is by design and is a fundamental security feature of private IP addressing.

If You Can't Access 192.168.200.1

If typing http://192.168.200.1 into your browser does not load a login page, there are several possible causes to investigate:

• Wrong gateway address: Your router may be using a different default IP. Open the Command Prompt on Windows (Start > Run > cmd) and type ipconfig /all. Look for the Default Gateway value under your active network adapter. On macOS or Linux, run netstat -nr | grep default in the Terminal. If the gateway shown is not 192.168.200.1, use that address instead, or check our guide to find your router IP address.
• Not connected to the right network: Ensure your computer or phone is connected to the router's own Wi-Fi network or plugged in via LAN cable. Accessing 192.168.200.1 from a different network will not work.
• Browser cache or extension conflict: Try opening an incognito/private browser window, or disable any VPN or proxy extensions that may be intercepting the request.
• Router is unresponsive: Power-cycle your router by unplugging it for 30 seconds and plugging it back in. Wait for it to fully boot, then try again.
• IP has been changed: A previous administrator may have changed the router's LAN IP from 192.168.200.1 to something else. In this case, you will need to perform a factory reset to restore the default settings.

Router Brands That Use 192.168.200.1

Unlike the more widespread 192.168.1.1 or 10.0.0.1, the address 192.168.200.1 is associated with a smaller, more specific set of hardware manufacturers. Here are the confirmed brands and models that use it as their factory default gateway:

• Bitmain (AntRouter R1-LTC, AntRouter R1, AntRouter R3-LTC): Bitmain is best known as a cryptocurrency mining hardware manufacturer. Their AntRouter line combines a wireless router with a built-in Litecoin or Bitcoin miner. These devices ship with 192.168.200.1 as the default IP and use root / root as the default login credentials. The admin interface is a lightweight OpenWrt-based panel.
• Westell (VersaLink 327W): Westell is a US-based DSL equipment manufacturer. The VersaLink 327W is a DSL modem/router combo that uses 192.168.200.1 as its default LAN gateway. Default credentials are typically admin / password. Westell devices were commonly deployed by ISPs in the United States.
• MQmaker (WiTi Board): MQmaker's WiTi Board is a single-board computer with built-in Wi-Fi routing capabilities. Some firmware configurations default to 192.168.200.1. Login credentials vary but are commonly root / root or admin / admin.

If your device is not one of the above but still resolves to 192.168.200.1, it may have been manually configured to use this address, or it may be a less-documented model. In that case, check the label on the bottom or back of your device for the default gateway and credentials.

Changing Your Router's Password at 192.168.200.1

Keeping your router secured with a strong, unique password is one of the most important steps you can take to protect your home or office network. The factory default credentials for devices using 192.168.200.1 — such as root/root on Bitmain AntRouters or admin/password on Westell gateways — are publicly known and should be changed immediately after setup.

To change your router's admin password, log in to http://192.168.200.1 using your current credentials. Navigate to the Administration, System, or Management section of the interface (the exact label depends on your router's firmware). Look for a Change Password or Admin Password field. Enter your new password twice to confirm it, then save. Make sure your new password is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Store it somewhere safe — if you forget it, you will need to perform a factory reset to regain access.

Router Username and Password List

How to Factory Reset a Router Using 192.168.200.1

If you've forgotten your admin credentials or your router is behaving unexpectedly, a factory reset will restore all settings — including the default IP address of 192.168.200.1 — to their original state. The exact procedure varies slightly by brand:

• Bitmain AntRouter R1-LTC / R1: Locate the small reset button on the device. Press and hold it for at least 5 seconds while the device is powered on. According to Bitmain's official support documentation, a five-second long press will reset the AntRouter to its factory defaults. The device will reboot and return to 192.168.200.1 with root / root credentials.
• Westell VersaLink 327W: Press and hold the reset button on the back of the unit while plugging in the power cord. Continue holding the button until the device's indicator lights cycle, then release. The router will reboot with 192.168.200.1 restored as the default gateway and admin / password as the login.
• MQmaker WiTi Board: Press and hold the reset button for approximately 10 seconds until the device reboots. After the reset, access the admin panel at 192.168.200.1 using the default credentials printed on the device or in its documentation.

Important: A factory reset will erase all custom settings, including your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and any static IP assignments. Make sure to back up your configuration before resetting if your router's firmware supports it.

What Is 192.168.200.1 — Understanding Private IP Addresses

192.168.200.1 is a private Class C IPv4 address. Private IP addresses are defined by RFC 1918 and are reserved exclusively for use within local networks — they are never routed over the public internet. The three private IPv4 ranges are:

• 10.0.0.0 – 10.255.255.255 (Class A)
• 172.16.0.0 – 172.31.255.255 (Class B)
• 192.168.0.0 – 192.168.255.255 (Class C)

192.168.200.1 falls within the Class C private range. When your router uses this address as its gateway, all devices that connect to it will be assigned IP addresses within the 192.168.200.x subnet — for example, 192.168.200.2, 192.168.200.3, and so on, up to 192.168.200.254. These addresses are distributed automatically by the router's DHCP server.

Your router acts as the bridge between this private subnet and the public internet. When you browse a website, your device sends the request to 192.168.200.1 (the gateway), which forwards it to your ISP and then to the wider internet. Responses travel back the same way. This process — called Network Address Translation (NAT) — allows many devices to share a single public IP address assigned by your ISP.

The 192.168.200.x subnet is less commonly used than 192.168.1.x or 192.168.0.x, which makes it a useful choice in environments where multiple routers or VLANs are in use, as it reduces the chance of subnet overlap and IP conflicts.

Related IP Addresses in the 192.168.200.x Subnet

If you're working within a network that uses 192.168.200.1 as its gateway, the following IP addresses are part of the same /24 subnet (192.168.200.0/24) and may be relevant to your configuration:

• 192.168.200.2 – 192.168.200.254: These are the addresses your router's DHCP server will assign to connected devices such as computers, smartphones, smart TVs, and printers.
• 192.168.200.100 – 192.168.200.200: A common DHCP pool range configured on routers using this subnet. Devices connecting dynamically will typically receive an address in this range.
• 192.168.200.254: Sometimes used as an alternative gateway address on devices in this subnet, particularly on certain DSL modems and managed switches.
• 192.168.200.255: This is the broadcast address for the 192.168.200.0/24 subnet and cannot be assigned to any individual device.

Other commonly used default gateway addresses you may encounter on different routers include 192.168.1.254, 192.168.8.1, 192.168.10.1, and 192.168.100.1. If you need to connect two routers on the same physical network, make sure they use different subnets — for example, one on 192.168.1.x and another on 192.168.200.x — to avoid routing conflicts.

Frequently Asked Questions About 192.168.200.1

What is 192.168.200.1?

192.168.200.1 is a private Class C IPv4 address used as the default gateway (router login IP) by specific router brands including Bitmain (AntRouter series), Westell (VersaLink 327W), and MQmaker (WiTi Board). You can use it to access your router's admin panel and configure your network settings.

How do I log in to 192.168.200.1?

Open a web browser and navigate to http://192.168.200.1. When the login page appears, enter your username and password. For Bitmain AntRouter devices, use root / root. For Westell VersaLink routers, try admin / password. For MQmaker devices, try admin / admin or root / root.

Why is 192.168.200.1 not loading in my browser?

The most common reasons are: you are not connected to the correct network, your router uses a different gateway IP, or the router needs to be rebooted. Run ipconfig /all on Windows or netstat -nr | grep default on macOS to confirm your actual gateway address. If it differs from 192.168.200.1, use that address instead.

Is 192.168.200.1 safe to use?

Yes. Like all private IP addresses in the 192.168.x.x range, 192.168.200.1 is only accessible from within your local network and is never exposed to the public internet. However, you should always change the default admin password on your router to prevent unauthorized access from within your network.

Can two devices on my network share 192.168.200.1?

No. Only one device — your router or gateway — should be assigned 192.168.200.1. If two devices on the same network share this address, an IP address conflict will occur, causing connectivity issues for both devices. Your router's DHCP server automatically prevents this for dynamically assigned addresses, but you should be careful when assigning static IPs manually.

What is the default username and password for 192.168.200.1?

The default credentials depend on your router brand. For Bitmain AntRouter devices: root / root. For Westell VersaLink 327W: admin / password. For MQmaker WiTi Board: root / root or admin / admin. Always change these defaults after your first login to secure your network.