192.168.1.64 Admin Login

Hikvision — one of the world's leading manufacturers of IP surveillance cameras, NVRs, and DVRs — uses 192.168.1.64 as the factory-default IP address across its broad range of IP cameras and network video recorders. When you unbox a Hikvision IP camera or NVR and connect it to your local network for the first time, the device is reachable at 192.168.1.64 before activation. This makes 192.168.1.64 one of the most recognizable default IPs in the IP surveillance and security camera industry. It is a Class C private IPv4 address belonging to the 192.168.1.0/24 subnet, which supports up to 254 usable host addresses. Other devices and routers on the same subnet may also be assigned 192.168.1.64 by a DHCP server, but its strongest association remains with Hikvision hardware. Other commonly used default gateways in the same private range include 192.168.1.254 and 192.168.0.1.

How to Access 192.168.1.64

To access the admin or configuration interface at 192.168.1.64, open your preferred web browser and type http://192.168.1.64 directly into the address bar — do not use a search engine. For Hikvision IP cameras and NVRs, this will load the device's web-based activation and login page. Before you can log in for the first time, Hikvision requires you to activate the device by setting a strong administrator password. This is a mandatory security step enforced by Hikvision on all modern firmware versions.

Important: your computer must be on the same 192.168.1.x subnet to reach 192.168.1.64. If your PC is currently on a different subnet (for example, 192.168.0.x), you will need to temporarily assign your network adapter a static IP such as 192.168.1.2 with a subnet mask of 255.255.255.0. Once you are on the same subnet, navigate to http://192.168.1.64 and the Hikvision login or activation page will load. After completing setup, you can reassign your PC back to DHCP or its original static address.

Hikvision Device Activation at 192.168.1.64

Unlike a standard router login page, accessing 192.168.1.64 on a brand-new Hikvision device will first present you with an activation screen rather than a login prompt. This is a critical distinction. You must complete activation before any login is possible. Here is how to activate your Hikvision device via web browser:

1. Connect your Hikvision IP camera or NVR directly to your PC or to a switch on the same network segment.
2. Set your PC's IP address to a static address in the same subnet, such as 192.168.1.2, with subnet mask 255.255.255.0.
3. Open your browser and navigate to http://192.168.1.64.
4. On the activation page, create a strong administrator password (minimum 8 characters, mixing uppercase, lowercase, numbers, and special characters). Hikvision enforces password complexity requirements.
5. Confirm the password and click OK or Activate.
6. Once activated, you will be redirected to the standard login page. Enter admin as the username and the password you just created.
7. After logging in, navigate to Configuration > Network > Basic Settings to assign a new static IP or enable DHCP so the camera integrates into your existing network.

Alternatively, you can use Hikvision's free SADP (Smart Active Detection Protocol) tool or the iVMS-4200 client software to discover, activate, and modify the IP address of your device over the LAN without needing to manually reconfigure your PC's network adapter.

If You Can't Access 192.168.1.64

If typing http://192.168.1.64 into your browser returns an error or a blank page, work through the following checks before assuming the device is faulty:

• Subnet mismatch: This is the most common cause. Your PC must be on the 192.168.1.x subnet. Open a command prompt (Windows: Start > cmd, then type ipconfig) and verify your IPv4 address starts with 192.168.1. If it does not, temporarily set a static IP of 192.168.1.2 on your network adapter.
• Wrong default IP: Some Hikvision models ship with DHCP enabled by default, meaning the device may have already received a different IP from your router. Use the SADP tool to scan your network and discover the actual current IP of the device.
• Firewall or browser issue: Disable your PC firewall temporarily and try a different browser. Hikvision's web interface works best in Internet Explorer (legacy) or browsers with NPAPI plugin support. For modern browsers, use the iVMS-4200 desktop client instead.
• Cable or power issue: Confirm the device is powered on and the Ethernet cable is securely connected. Check for link indicator LEDs on both the device and the switch/router port.
• IP already changed: If someone previously configured the device, the IP may have been changed from 192.168.1.64. Use SADP to find the current address, or perform a factory reset to restore 192.168.1.64 as the default.

If none of the above resolves the issue, check our guide to find your device's IP address for further assistance.

Factory Reset: Restoring 192.168.1.64 on Hikvision Devices

If you have forgotten the admin password for your Hikvision device or the IP address has been changed from 192.168.1.64, a factory reset will restore all settings — including the default IP — to their original state. The exact reset method depends on your device type:

Hikvision IP Camera — Physical Reset Button

1. Locate the reset button on your camera. On most models it is a small pinhole button near the cable connections or inside the camera housing. You may need a paperclip or pin to press it.
2. Disconnect the power supply from the camera.
3. Press and hold the reset button, then reconnect the power while continuing to hold the button.
4. Hold the reset button for approximately 10–15 seconds (some models require up to 90 seconds — consult your model's manual).
5. Release the button and wait for the camera to fully reboot. The camera will return to its factory-default unactivated state with IP address 192.168.1.64.
6. You must now re-activate the device by setting a new admin password before you can log in.

Hikvision NVR — Software Reset via Menu

1. Connect a monitor and mouse to the NVR and log in with your admin credentials.
2. Navigate to Menu > Maintenance > Default.
3. Select Factory Defaults to erase all settings and restore the device to its original configuration.
4. The NVR will reboot. After restart, all cameras and network settings will be cleared and the device will be ready for fresh setup.

Warning: A factory reset permanently erases all custom configurations, including network settings, recording schedules, and user accounts. Back up your configuration first if possible via Menu > Maintenance > Import/Export.

Changing Your Password on a Hikvision Device at 192.168.1.64

Keeping your Hikvision device secured with a strong, unique password is essential — especially for internet-connected surveillance systems. To change your admin password after logging in at 192.168.1.64:

1. Log in to the web interface at http://192.168.1.64 using your current admin credentials.
2. Click on Configuration in the top navigation bar.
3. Go to System > User Management.
4. Select the admin user and click Modify.
5. Enter your current password, then type and confirm your new password. Hikvision requires a minimum of 8 characters with a mix of character types.
6. Click OK to save. You will be prompted to log in again with the new password.

Never leave your Hikvision device with a weak or default password, particularly if the device is accessible remotely over the internet. Hikvision devices with weak passwords have historically been targeted by botnets and unauthorized access attempts. A strong password at 192.168.1.64 is your first line of defense.

Router & Device Username and Password List

What Is 192.168.1.64 and Why Does Hikvision Use It?

192.168.1.64 is a Class C private IPv4 address within the 192.168.1.0/24 network block. Private IP addresses in the 192.168.x.x range are reserved by RFC 1918 for use within local area networks (LANs) and are not routable on the public internet. This means 192.168.1.64 can be used freely on any private network without conflicting with public internet addresses.

The 192.168.1.0/24 subnet provides 254 usable host addresses — from 192.168.1.1 to 192.168.1.254. The address 192.168.1.64 sits in the middle of this range, and Hikvision chose it as the factory default for its IP cameras and NVRs to avoid conflicts with the most common router default gateway addresses such as 192.168.1.254 and 192.168.0.1, which occupy the lower and upper ends of common private subnets.

When you connect a Hikvision camera to your network, it initially claims 192.168.1.64 as its static address. Once you activate and configure the device, it is best practice to either assign it a new static IP that fits your network's addressing scheme or enable DHCP so your router assigns it a dynamic address — freeing up 192.168.1.64 or preventing address conflicts if you have multiple Hikvision devices on the same network.

Beyond Hikvision, 192.168.1.64 can also appear as a DHCP-assigned address on any home or office network using the 192.168.1.x range. Your router's DHCP server may assign 192.168.1.64 to any connected device — a laptop, smartphone, smart TV, or printer — depending on the order in which devices connect and the DHCP pool configuration.

Related IP Addresses in the 192.168.1.x Subnet

The 192.168.1.0/24 subnet is one of the most widely used private network ranges in home and small office environments. Several IP addresses within this subnet are commonly assigned as default gateways or device defaults. Here are the most notable ones you may encounter alongside 192.168.1.64:

• 192.168.1.254 — Used as the default gateway by many DSL routers and ISP-provided modems, particularly those from BT, Sky, and various European ISPs.
• 192.168.0.1 — One of the most common default gateway addresses globally, used by Netgear, D-Link, and many other router brands on the adjacent 192.168.0.x subnet.
• 192.168.2.1 — Default gateway used by some Cisco Linksys routers and other networking equipment.
• 192.168.8.1 — Default gateway used by Huawei mobile Wi-Fi routers and MiFi hotspot devices.
• 192.168.10.1 — Used by certain Ubiquiti and other enterprise-grade networking devices as their default management IP.
• 192.168.100.1 — Commonly used by cable modems and ISP gateway devices as their default management address.
• 10.0.0.1 — A Class A private address used by some routers and ISP equipment as an alternative default gateway.

Understanding the full 192.168.1.x address space helps you avoid IP conflicts when adding new devices like your Hikvision camera to an existing network. Always check your router's DHCP pool and any statically assigned addresses before setting 192.168.1.64 as a permanent static IP for your surveillance device.

Frequently Asked Questions About 192.168.1.64

What device uses 192.168.1.64 as its default IP?

192.168.1.64 is most prominently associated with Hikvision IP cameras, NVRs (Network Video Recorders), and DVRs. Hikvision officially documents 192.168.1.64 as the factory-default IP address for its IP camera product line. When you first connect a Hikvision camera out of the box, it is accessible at this address for initial activation and configuration.

How do I log in to 192.168.1.64?

Open your web browser and go to http://192.168.1.64. For a new Hikvision device, you will first see an activation page where you must set an admin password. After activation, log in with username admin and the password you created. Make sure your PC is on the same 192.168.1.x subnet before attempting to connect.

What is the default username and password for 192.168.1.64?

For Hikvision devices at 192.168.1.64, the default username is admin. However, Hikvision does not ship devices with a pre-set default password — you are required to create your own password during the mandatory activation process the first time you access the device. If you have forgotten your password, you will need to perform a factory reset to restore the device to its unactivated state and set a new password.

Why can't I access 192.168.1.64?

The most common reason you cannot reach 192.168.1.64 is a subnet mismatch — your computer is on a different network segment (e.g., 192.168.0.x) and cannot communicate with a device on 192.168.1.x. Temporarily set your PC's IP to 192.168.1.2 with subnet mask 255.255.255.0 and try again. Other causes include the Hikvision device having DHCP enabled (so it received a different IP from your router), a faulty cable, or the device not being powered on. Use Hikvision's free SADP tool to scan your network and find the device's actual current IP address.

How do I reset a Hikvision device to restore 192.168.1.64?

To restore 192.168.1.64 as the default IP on a Hikvision IP camera, locate the physical reset button on the camera body, disconnect the power, press and hold the reset button, reconnect the power while holding the button, and continue holding for 10–15 seconds (up to 90 seconds on some models). The camera will reboot to factory defaults with 192.168.1.64 as its IP. For Hikvision NVRs, go to Menu > Maintenance > Default > Factory Defaults through the on-screen interface.

Can I use 192.168.1.64 for other devices on my network?

Yes — 192.168.1.64 is a standard private IPv4 address and can be assigned to any device on a 192.168.1.x network. However, if you have a Hikvision camera on the same network that still has its factory default IP of 192.168.1.64, assigning the same address to another device will cause an IP address conflict, making both devices unreachable. Always ensure each device on your network has a unique IP address. It is best practice to change your Hikvision camera's IP away from 192.168.1.64 after initial setup to avoid conflicts.

Is 192.168.1.64 a public or private IP address?

192.168.1.64 is a private IP address as defined by RFC 1918. It belongs to the 192.168.0.0/16 private address block and is only valid within a local area network. It cannot be accessed directly from the public internet, which provides a layer of inherent security. To access your Hikvision device at 192.168.1.64 remotely over the internet, you would need to configure port forwarding on your router or use Hikvision's Hik-Connect cloud service for secure remote access.