192.168.1.50 Admin Login

192.168.1.50 is a Class C private IPv4 address used within the 192.168.1.0/24 subnet. It is most notably associated with Call-Direct routers (models CDM-882seu and CDR-780seu) and OKI network devices (model C3450) as their factory-set default gateway and admin interface address. While it is less common than gateway addresses like 192.168.1.1 or 192.168.0.1, 192.168.1.50 serves as a fully valid private IP that can be used by any device on a local network. Because it sits in the upper half of the typical DHCP range, it is also frequently assigned as a static IP to specific devices — such as printers, access points, NAS drives, or smart home controllers — that need a predictable, permanent address on your network.

How to Access 192.168.1.50

To reach the admin panel at 192.168.1.50, make sure your computer or device is connected to the same local network — either via an Ethernet cable or over Wi-Fi. Then open any web browser (Chrome, Firefox, Edge, Safari) and type http://192.168.1.50 directly into the address bar. Do not use a search engine — paste it straight into the URL bar and press Enter.

If your device uses 192.168.1.50 as its default gateway, you will be greeted with a login prompt. For Call-Direct CDM-882seu and Call-Direct CDR-780seu routers, the default credentials are username: admin and password: password. For the OKI C3450, use username: admin and password: heslo. Once logged in, you can manage your wireless settings, change your SSID, update your Wi-Fi password, configure port forwarding, set up parental controls, and monitor connected devices.

It is strongly recommended that you use a wired (Ethernet) connection when making changes to your router settings. This prevents you from being unexpectedly disconnected mid-session when you save a configuration change — especially if you are modifying wireless settings.

If You Can't Access 192.168.1.50

If typing http://192.168.1.50 into your browser does not load a login page, there are several possible reasons and fixes to try:

• Wrong gateway address: 192.168.1.50 may not be your router's actual default gateway. Open the Command Prompt on Windows (Start > type cmd > Enter) and run ipconfig /all. Look for the Default Gateway field. On macOS or Linux, run netstat -nr or check System Preferences > Network. If the gateway shown is different — such as 192.168.1.1 or 192.168.1.254 — use that address instead.
• Not connected to the network: Confirm your device is connected to the router's Wi-Fi or plugged in via Ethernet. You cannot reach 192.168.1.50 from outside the local network.
• IP address was changed: A previous administrator may have changed the default IP from 192.168.1.50 to something else. In this case, you will need to perform a factory reset to restore the original address.
• Browser cache or HTTPS issue: Try clearing your browser cache or using a private/incognito window. Also make sure you are typing http:// (not https://) — most router admin panels do not use SSL by default.
• Firewall blocking the connection: Temporarily disable any firewall or VPN software on your computer and try again.

If none of these steps work, consult our guide on how to find your router IP address for a full walkthrough.

Router Brands That Use 192.168.1.50

Unlike the most common gateway addresses, 192.168.1.50 is used by a smaller, specific set of manufacturers. The confirmed brands and models that ship with 192.168.1.50 as their default IP are:

• Call-Direct CDM-882seu — Default username: admin | Default password: password
• Call-Direct CDR-780seu — Default username: admin | Default password: password
• OKI C3450 — Default username: admin | Default password: heslo

The Call-Direct brand produces ADSL modem-routers primarily distributed through telecommunications providers. The CDM-882seu and CDR-780seu are DSL gateway devices that combine modem and router functionality, making 192.168.1.50 the single address you use for both internet configuration and local network management.

The OKI C3450 is a networked colour laser printer. Its built-in network interface card (NIC) uses 192.168.1.50 as the default IP for its embedded web-based admin panel, where you can manage print queues, configure network settings, update firmware, and set access controls. This is a notable distinction — 192.168.1.50 is not exclusively a router address; it is also the default management IP for certain networked printers and multifunction devices.

Beyond these specific models, 192.168.1.50 is also commonly seen as a DHCP-assigned or manually configured static IP for secondary devices on networks where the primary router uses 192.168.1.1 as the gateway. Devices such as wireless access points (e.g., ASUS routers in AP mode), network-attached storage (NAS) units, IP cameras, and smart home hubs are frequently assigned 192.168.1.50 to keep them easily identifiable and reachable within the subnet.

Changing Your Password at 192.168.1.50

Whether you are using a Call-Direct router or an OKI network device, changing the default password at 192.168.1.50 is one of the most important steps you can take to secure your network. Default passwords like password and heslo are publicly documented and well-known to attackers — leaving them unchanged is a serious security risk.

To change your password, log in to the admin panel at http://192.168.1.50 using the default credentials listed above. Once inside, navigate to the Administration, System, or Management section (the exact label varies by device). Look for a Change Password or Admin Password option. You will typically be asked to enter your current password, then type and confirm your new password.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Write it down and store it somewhere safe — if you forget the admin password for your device at 192.168.1.50, the only recovery option is a full factory reset, which will erase all your custom settings.

Router Username and Password List

How to Factory Reset a Device Using 192.168.1.50

If you have forgotten your admin password, or if the login page at 192.168.1.50 is not responding as expected, a factory reset will restore your device to its original default settings — including the default IP address, username, and password.

For Call-Direct CDM-882seu and CDR-780seu routers:

1. Locate the small Reset button on the back or bottom of the router. It is usually recessed to prevent accidental presses.
2. With the router powered on, use a straightened paperclip or toothpick to press and hold the Reset button for approximately 10–20 seconds.
3. Release the button when the router's indicator lights flash or change pattern, signalling that the reset has begun.
4. Wait for the router to fully reboot — this typically takes 60–90 seconds.
5. Once rebooted, the router will be restored to factory defaults. You can now access the admin panel at http://192.168.1.50 using admin / password.

For OKI C3450 networked printers:

1. On the printer's front panel, press the Menu button to enter the settings menu.
2. Navigate to Admin Setup and enter the administrator password (default: heslo).
3. Locate the Network or Network Setup option and select Factory Default or Initialize NIC.
4. Confirm the reset. The printer's network interface will reboot and restore 192.168.1.50 as the default IP.
5. You can then access the OKI C3450 web admin panel at http://192.168.1.50 using admin / heslo.

Important: A factory reset will erase all custom configurations, including your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and any static IP assignments. Make sure to back up your settings before performing a reset if your device supports it.

What Is 192.168.1.50 as a Private IP Address?

192.168.1.50 is a Class C private IPv4 address that falls within the reserved private range of 192.168.0.0 – 192.168.255.255, as defined by RFC 1918. This means it is not routable on the public internet — it exists exclusively within your local area network (LAN). No data sent to or from 192.168.1.50 will travel beyond your router without being translated by NAT (Network Address Translation).

Within the 192.168.1.0/24 subnet, there are 254 usable host addresses ranging from 192.168.1.1 to 192.168.1.254. The address 192.168.1.50 sits in the middle of this range, making it a popular choice for both default device IPs and manually assigned static addresses. When your router's DHCP server is active, it typically hands out addresses starting from 192.168.1.2 or 192.168.1.100 upward — meaning 192.168.1.50 may or may not fall within the automatic DHCP pool depending on your router's configuration.

Because 192.168.1.50 is a private address, multiple networks around the world can use it simultaneously without conflict — each one is isolated within its own LAN. The only rule is that no two devices on the same network should share the address 192.168.1.50 at the same time, as this would cause an IP address conflict that disrupts connectivity for both devices.

192.168.1.50 and the 192.168.1.x Subnet

The 192.168.1.0/24 subnet is one of the most widely used private network ranges in home and small-office environments. The primary gateway on this subnet is almost always 192.168.1.1, used by brands such as Linksys, ASUS, TP-Link, and many others. The address 192.168.1.50 is one of many host addresses available within this subnet, and it plays several roles depending on your network setup:

• Default device IP: As documented above, Call-Direct routers and OKI printers ship with 192.168.1.50 pre-configured as their management address.
• Static IP for secondary devices: Network administrators frequently assign 192.168.1.50 as a fixed static IP to devices that need a permanent, predictable address — such as a secondary access point, a NAS device, a network printer, or a Raspberry Pi server.
• DHCP lease: If your router's DHCP pool includes the .50 range, a device connecting to your network may automatically receive 192.168.1.50 as its temporary IP lease.

Other commonly used addresses in the same subnet include 192.168.1.1 (primary gateway), 192.168.1.254 (used by some ISP-provided routers), and 192.168.1.100 (a common DHCP start address). Related subnets you may encounter include 192.168.0.1 and 192.168.2.1.

Frequently Asked Questions About 192.168.1.50

What router uses 192.168.1.50 as its default IP?

The confirmed routers and network devices that use 192.168.1.50 as their factory default IP address are the Call-Direct CDM-882seu, the Call-Direct CDR-780seu, and the OKI C3450 networked printer. If you own one of these devices and have not changed the default IP, you can access its admin panel by navigating to http://192.168.1.50 in your browser.

What is the default username and password for 192.168.1.50?

For Call-Direct routers (CDM-882seu and CDR-780seu), the default login is username: admin and password: password. For the OKI C3450, use username: admin and password: heslo. If these credentials do not work, the password may have been changed by a previous user — in that case, you will need to perform a factory reset to restore the defaults.

Is 192.168.1.50 a public or private IP address?

192.168.1.50 is a private IP address. It belongs to the Class C private range (192.168.0.0/16) defined by RFC 1918 and cannot be accessed from the public internet. It is only reachable by devices connected to the same local network.

Why is my device showing 192.168.1.50 as its IP?

Your device may have been assigned 192.168.1.50 by your router's DHCP server, or it may have been manually configured with a static IP of 192.168.1.50. This is completely normal. If you own a Call-Direct router or OKI C3450, this is also the default management IP for those devices. To check your current IP and gateway, run ipconfig /all on Windows or ifconfig on macOS/Linux.

Can two devices on my network both use 192.168.1.50?

No. Only one device on your local network can use 192.168.1.50 at any given time. If two devices are assigned the same IP address, an IP address conflict will occur, causing both devices to lose network connectivity. Make sure your DHCP server does not assign 192.168.1.50 to another device if you have already reserved it for a specific piece of hardware.

How do I set 192.168.1.50 as a static IP for my device?

You can assign a static IP of 192.168.1.50 in two ways: either configure it directly on the device (via its network settings, using subnet mask 255.255.255.0 and your router's gateway address such as 192.168.1.1), or use your router's DHCP reservation feature to permanently bind 192.168.1.50 to a specific device's MAC address. The DHCP reservation method is generally preferred as it keeps all IP management centralised in the router's admin panel at addresses like 192.168.1.1 or 192.168.1.254.

What should I do if I forgot the password for 192.168.1.50?

If you have forgotten the admin password for your Call-Direct or OKI device at 192.168.1.50, your only option is to perform a factory reset. Press and hold the Reset button on the back of your Call-Direct router for 10–20 seconds until the lights flash. For the OKI C3450, use the front panel menu to navigate to Admin Setup and select the network reset option. After the reset, you can log in with the original default credentials: admin / password for Call-Direct, or admin / heslo for OKI.