192.168.1.250 Admin Login

Several router and networking device brands use 192.168.1.250 as their default IP address, most notably Netgear WiFi range extenders (such as the EX6200, EX6400, EX7300, WN3000RP, and WN3500RP), Linksys wireless access points (including the WAP11 and WAP51AB), 3Com (model 3CRWE454G75), Airlink (AP311W, AP421W, AP431W), TRENDnet (TEW-410APB), and Sitecom (WL-105b). It is used as a private IPv4 network address and serves as the router or extender gateway within the 192.168.1.0/24 subnet. Because 192.168.1.250 sits near the high end of the subnet range, it is particularly popular for range extenders and access points that need to coexist on the same network as a primary router (which typically occupies 192.168.1.1). Other commonly used default gateways in this family include 192.168.0.1 and 10.0.0.1.

How to Access 192.168.1.250

To reach your device's admin panel at 192.168.1.250, make sure you are connected to the same local network — either via Wi-Fi or an Ethernet cable. Then open any web browser (Chrome, Firefox, Edge, or Safari) and type http://192.168.1.250 directly into the address bar. Do not type it into a search engine — it must go into the address bar at the top of the browser window. Press Enter and you should be taken directly to the login page of your router, extender, or access point.

If the page loads over a secure connection, try https://192.168.1.250 instead. For Netgear extenders like the EX6200 or EX6400, you can also try navigating to mywifiext.net or mywifiext.local as an alternative URL that redirects to the 192.168.1.250 admin panel. Once you are on the login page, enter your username and password. The most common default credentials for devices using this IP are admin / password (Netgear), admin / admin (Airlink, TRENDnet, Sitecom), or a blank username with admin as the password (Linksys WGA54G). Always check the label on the bottom or back of your device for the exact factory defaults.

If You Can't Access 192.168.1.250

If typing http://192.168.1.250 into your browser returns an error or a blank page, there are several things you should check. First, confirm that 192.168.1.250 is actually the correct gateway for your device. Open a Command Prompt on Windows (Start > Run > cmd) and type ipconfig /all, then press Enter. Look for the Default Gateway field — if it shows a different address, that is the IP you should be using instead. On a Mac, go to System Settings > Network, select your active connection, and check the Router field. You can also check our guide to find your router IP address.

Second, make sure you are connected to the correct network. Netgear extenders using 192.168.1.250 must be accessed from a device connected to the extender's own network or the main router's network (once the extender is set up). Third, try disabling any VPN or proxy software, as these can reroute your traffic and prevent local IP access. Finally, try a different browser or clear your browser's cache. If none of these steps work, a factory reset (described below) will restore 192.168.1.250 as the default IP.

Default Username and Password for 192.168.1.250 Devices

The default login credentials for devices using 192.168.1.250 vary by brand and model. Here is a quick reference for the most common ones:

• Netgear (EX6200, EX6400, EX7300, WN1000RP, WN2500RP, WN3000RP, WN3500RP): Username — admin | Password — password
• Linksys (WAP11 v1.0, WAP11 v1.1, WAP51AB): Username — blank | Password — public or admin
• Linksys (WGA54G): Username — blank | Password — admin
• Linksys (WGA600N): Username — admin | Password — admin
• 3Com (3CRWE454G75): Username — admin | Password — blank
• Airlink (AP311W, AP421W, AP431W): Username — admin | Password — admin
• TRENDnet (TEW-410APB): Username — admin | Password — admin
• Sitecom (WL-105b): Username — admin | Password — admin
• REPOTEC (RP-WAC1420): Username — admin | Password — 12345

If you have changed your password and cannot remember it, you will need to perform a factory reset on your device to restore these defaults. Never leave the default password in place on a live network — always change it to something strong and unique after your first login.

Changing Your Password at 192.168.1.250

Once you have successfully logged into your device's admin panel at 192.168.1.250, one of the first things you should do is change the default password. Leaving the factory default password in place makes your network vulnerable to unauthorized access. To change it, look for a section labeled Administration, Management, or Advanced Settings within the admin panel. On Netgear extenders (EX6200, EX6400, etc.), navigate to Settings > Password to update your admin credentials. On Linksys access points, look under the Administration tab. You will typically be asked to enter your current password, then type and confirm your new password. Choose a password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. After saving, you will be logged out and prompted to log back in with your new credentials.

Router Username and Password List

How to Factory Reset a Device Using 192.168.1.250

If you are locked out of your admin panel at 192.168.1.250 or your device is behaving unexpectedly, a factory reset will restore all settings — including the IP address, username, and password — back to their original defaults. The exact procedure varies slightly by brand:

• Netgear Extenders (EX6200, EX6400, EX7300, WN3000RP, WN3500RP, etc.): With the extender powered on, locate the Factory Reset button (usually a small pinhole on the side or rear panel). Use a straightened paper clip or pin to press and hold the button until the Power LED blinks amber. Release the button and wait for the extender to reboot — this typically takes 1–2 minutes. Once it restarts, 192.168.1.250 will be restored as the default IP.
• Linksys Access Points (WAP11, WAP51AB, WGA54G, WGA600N): Locate the Reset button on the back or bottom of the unit. Press and hold it for 10–30 seconds using a pin or paper clip until the status LEDs flash, then release. The device will reboot with factory defaults restored.
• TRENDnet (TEW-410APB): Press and hold the reset button on the rear of the device for approximately 15–20 seconds until the LEDs indicate a reset, then release and allow the unit to reboot.
• Airlink (AP311W, AP421W, AP431W): Hold the reset pinhole button for 10 seconds until the power LED flashes, then release. The device will restart with all factory settings restored.
• 3Com (3CRWE454G75): Press and hold the reset button for 10 seconds. The device will reboot and restore 192.168.1.250 as the default gateway.

Important: A factory reset will erase all custom configurations, including your Wi-Fi name (SSID), password, and any port forwarding or security rules you have set up. Make sure to back up your settings before performing a reset if possible.

What Is 192.168.1.250 and Why Is It Used?

192.168.1.250 is a private IPv4 address that falls within the Class C private IP range defined by RFC 1918 (192.168.0.0 – 192.168.255.255). This means it can only be used within a local area network (LAN) and is never routable on the public internet, which provides an inherent layer of security. Because it is a private address, any router, extender, or access point on any home or office network in the world can use 192.168.1.250 without conflicting with any other network.

The reason manufacturers like Netgear choose 192.168.1.250 specifically — rather than the more common 192.168.1.1 — is to avoid conflicts with the primary router on the same network. When you install a Netgear range extender, it joins your existing 192.168.1.x network. If the extender used 192.168.1.1 as its admin IP, it would clash with most home routers. By using 192.168.1.250 (near the top of the address range), the extender can coexist peacefully alongside your main router and all connected devices.

Within the 192.168.1.0/24 subnet, addresses are typically distributed as follows: the router gateway occupies a low address (like 192.168.1.1 or 192.168.1.254), client devices (laptops, phones, tablets) are dynamically assigned addresses in the middle range (e.g., 192.168.1.2 through 192.168.1.200), and static devices like extenders, access points, printers, and servers are often assigned high-end addresses like 192.168.1.250. This organizational convention makes network management much easier.

Related IP Addresses in the 192.168.1.x Subnet

The 192.168.1.0/24 subnet is one of the most widely used private networks in the world. If you are managing a network that includes a device at 192.168.1.250, you may also encounter these commonly used addresses:

• 192.168.1.1 — The most common default gateway for home routers (used by TP-Link, Linksys, D-Link, and many others). This is typically your primary router's admin IP.
• 192.168.1.254 — Used by some ISP-provided modems and routers (common with BT Home Hubs and some Cisco/Linksys models) as their default gateway.
• 192.168.1.2 – 192.168.1.100 — Typically the DHCP range assigned to client devices such as laptops, smartphones, and tablets on your network.
• 192.168.1.245 – 192.168.1.255 — The upper range of the subnet, often reserved for static assignments to access points, extenders, printers, and network-attached storage (NAS) devices. 192.168.1.250 falls squarely in this zone.

Other popular private IP gateways outside the 192.168.1.x range include 192.168.0.1, 192.168.8.1, 192.168.10.1, 192.168.100.1, and 10.0.0.1. If 192.168.1.250 is not working as your gateway, one of these alternatives may be the correct address for your device.

Frequently Asked Questions About 192.168.1.250

What devices use 192.168.1.250 as their default IP?

The most well-known devices that use 192.168.1.250 as their default admin IP are Netgear WiFi range extenders (EX6200, EX6400, EX7300, WN1000RP, WN2500RP, WN3000RP, WN3500RP), Linksys wireless access points (WAP11, WAP51AB, WGA54G, WGA54AG, WGA600N), 3Com (3CRWE454G75), Airlink (AP311W, AP421W, AP431W), TRENDnet (TEW-410APB), Sitecom (WL-105b), and REPOTEC (RP-WAC1420). Some ISP-provided routers may also be configured to use this address.

Why can't I reach 192.168.1.250 in my browser?

The most common reasons you cannot access 192.168.1.250 are: (1) you are not connected to the correct network, (2) your device's gateway is a different IP address, (3) a VPN or proxy is intercepting your traffic, or (4) the device's IP has been manually changed from the default. Run ipconfig /all (Windows) or check your network settings (Mac/Linux) to confirm your actual gateway. If the IP has been changed, a factory reset will restore 192.168.1.250.

Is 192.168.1.250 the same as my router's IP?

Not necessarily. If your primary router uses 192.168.1.1 or 192.168.1.254, then 192.168.1.250 likely belongs to a secondary device on your network — such as a Netgear range extender or a Linksys access point. Both devices share the same 192.168.1.x subnet but have different admin IP addresses to avoid conflicts.

What is the default password for 192.168.1.250?

The default password depends on your device's brand. For Netgear extenders, the default is username admin and password password. For Linksys access points, it is typically a blank username and password admin or public. For Airlink, TRENDnet, and Sitecom, both the username and password are admin. Always check the label on the bottom of your device for the exact factory credentials.

Can two devices on my network both use 192.168.1.250?

No. Just like any IP address, 192.168.1.250 can only be assigned to one device at a time on a given network. If two devices share the same IP, an IP address conflict will occur, causing both devices to lose connectivity. If you have multiple extenders or access points, make sure each one is assigned a unique IP address within the 192.168.1.x subnet.

How do I change the IP address of my device from 192.168.1.250 to something else?

Log into the admin panel at http://192.168.1.250 using your credentials. Navigate to the LAN Settings or Network Settings section. You will find a field for the device's IP address — change it to your desired address (e.g., 192.168.1.249) and save. The device will reboot and be accessible at the new IP. Make sure the new address does not conflict with any other device on your network.