192.168.1.200 Admin Login

Several router and networking device brands use 192.168.1.200 as their default IP address, including TRENDnet (TPL-210AP), Linksys (WPG54G), Hawking Technology (HW2R1), Loopcomm (LP-7316H), and UBIQCOM. This address sits within the 192.168.1.0/24 private subnet — one of the most widely deployed home and small-office network ranges in the world. Because 192.168.1.200 falls in the upper portion of the subnet's usable range, it is frequently assigned as a static default gateway for access points, powerline adapters, and wireless repeaters rather than primary routers. Other common default gateways in the same subnet include 192.168.1.254 and the ubiquitous 192.168.1.1. If you need to reach your device's admin panel, simply type http://192.168.1.200 into your browser's address bar while connected to the same network.

How to Access 192.168.1.200

Accessing the admin panel at 192.168.1.200 is straightforward, but you must be connected to the same local network as the device that uses this address. Follow these steps:

1. Connect your computer or smartphone to the router or access point — either via an Ethernet cable (recommended for stability) or over Wi-Fi.
2. Open any web browser — Chrome, Firefox, Edge, or Safari all work fine.
3. Type http://192.168.1.200 directly into the address bar and press Enter. Do not type it into a search engine — paste it into the URL bar at the very top of the browser window.
4. You should see a login page asking for a username and password. For most devices using this IP, the default credentials are admin / admin. Hawking HW2R1 devices use admin / 1234 by default. Check the label on the back or bottom of your device if those don't work.
5. Once logged in, you can configure Wi-Fi settings, change passwords, update firmware, set up port forwarding, and more.

Because 192.168.1.200 is a private IPv4 address, it is only reachable from within your local network — it is never exposed directly to the internet, which makes it inherently safe to access from your home or office.

If You Can't Access 192.168.1.200

If typing http://192.168.1.200 into your browser returns an error, a blank page, or a "site can't be reached" message, work through the following checks before assuming the device is faulty:

• Verify your gateway address. On Windows, open Command Prompt (Start > type cmd > Enter) and run ipconfig /all. Look for the Default Gateway field. On macOS or Linux, run netstat -nr or ip route. If the gateway shown is not 192.168.1.200, your device may be using a different IP — check our guide to find your router IP address.
• Check your cable or Wi-Fi connection. A loose Ethernet cable or a dropped Wi-Fi connection will prevent the browser from reaching 192.168.1.200 entirely. Try reconnecting or swapping the cable.
• Disable VPN software. Active VPN clients often reroute traffic away from your local subnet, making 192.168.1.200 unreachable. Temporarily disable any VPN and try again.
• Try HTTPS. Some newer firmware versions on TRENDnet and UBIQCOM devices enforce HTTPS. Try https://192.168.1.200 and accept any browser security warning about the self-signed certificate.
• Clear your browser cache or try a different browser. Cached redirects can sometimes send you to the wrong address.
• Check for IP conflicts. If another device on your network has been manually assigned 192.168.1.200, an address conflict will prevent the admin panel from loading. Log into your primary router (often at 192.168.1.1 or 192.168.0.1) and review the DHCP client list to spot any conflicts.

Router Brands That Use 192.168.1.200

Unlike the more common gateway addresses such as 192.168.1.1 or 192.168.0.1, the address 192.168.1.200 is used by a smaller, more specific set of devices. Here is a breakdown of the confirmed brands and models:

• TRENDnet — TPL-210AP: This is a Powerline 200 AV Wireless N Access Point. TRENDnet's official Quick Installation Guide explicitly states that the TPL-210AP's default IP address is 192.168.1.200. Default login credentials are admin / admin. The device bridges a powerline network with a wireless access point, and its admin panel lets you configure the wireless SSID, encryption, and powerline pairing.
• Linksys — WPG54G: The Wireless-G Presentation Player ships with a static IP of 192.168.1.200 out of the box, as confirmed in Linksys's official user guide. This device is designed for wireless presentations and uses this address for its configuration interface. Default credentials are admin with no password.
• Hawking Technology — HW2R1: The HW2R1 Smart Repeater uses 192.168.1.200 as its recommended default IP address. Hawking's own product manual lists this as the default value for the device's IP address field. Default credentials are admin / 1234.
• Loopcomm — LP-7316H: This wireless router/access point uses 192.168.1.200 as its default login IP. Default credentials are admin / admin.
• UBIQCOM: UBIQCOM, an Indian FTTH/XPON ONU manufacturer, uses 192.168.1.200 as the default IP for certain gateway models. These devices are commonly deployed by ISPs in fiber-to-the-home installations.

If your device is not listed above but you believe it uses 192.168.1.200, check the sticker on the back or bottom of the unit, or consult the printed quick-start guide that came in the box.

Changing Your Router's Password at 192.168.1.200

Keeping the default password on any device accessible at 192.168.1.200 is a significant security risk. Anyone connected to your network — including guests on your Wi-Fi — could log in and change your settings. Here is how to update it:

1. Log in to the admin panel at http://192.168.1.200 using your current credentials.
2. Navigate to the Administration, Management, or System section — the exact label varies by brand. On TRENDnet devices, look under Management > Admin. On Linksys devices, look under Administration > Management.
3. Locate the Admin Password or Router Password field.
4. Enter your new password twice to confirm it, then click Save or Apply.
5. You will be prompted to log in again with the new password immediately.

Choose a strong password of at least 12 characters, mixing uppercase letters, lowercase letters, numbers, and symbols. Avoid using your Wi-Fi password as your admin password — they should always be different.

Router Username and Password List

Factory Reset for Devices Using 192.168.1.200

If you have forgotten your admin password or the device at 192.168.1.200 is behaving unexpectedly, a factory reset will restore all settings to their out-of-box defaults — including the IP address, username, and password. The exact procedure varies slightly by brand:

• TRENDnet TPL-210AP: Locate the small reset pinhole on the device's body. With the device powered on, insert a straightened paperclip or pin into the hole and hold it for 15 seconds until the LEDs flash, then release. The device will reboot and return to its default state with IP 192.168.1.200 and credentials admin / admin.
• Linksys WPG54G: Press and hold the reset button on the back of the unit for 10 seconds while the device is powered on. Release when the power LED begins to flash. The device will restart with its default static IP of 192.168.1.200.
• Hawking HW2R1: Hold the reset button for 10–15 seconds until the device restarts. After the reset, the IP reverts to 192.168.1.200 and the password returns to 1234.
• Loopcomm LP-7316H: Press and hold the reset button for approximately 10 seconds. The device will reboot and restore default settings, including the 192.168.1.200 address and admin / admin credentials.
• UBIQCOM devices: Most UBIQCOM ONUs have a dedicated reset button on the rear panel. Hold it for 10–15 seconds with the device powered on until the indicator lights cycle, then release.

Important: A factory reset erases all custom configurations — your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and any other changes you have made. Make sure you have noted down your ISP settings (PPPoE username/password, VLAN IDs) before performing a reset, as you will need to re-enter them afterward.

What Is 192.168.1.200 and Why Is It a Private IP Address?

192.168.1.200 is a Class C private IPv4 address that belongs to the 192.168.0.0/16 block reserved by the Internet Assigned Numbers Authority (IANA) under RFC 1918. This means it can never be routed on the public internet — it exists exclusively within private local area networks (LANs). Your ISP, web servers, and external services will never see 192.168.1.200 directly; instead, your router translates it to your public IP address using a process called Network Address Translation (NAT).

Within the 192.168.1.0/24 subnet, the usable address range runs from 192.168.1.1 to 192.168.1.254, giving you up to 254 unique device addresses. The address 192.168.1.200 sits near the top of this range, which is why manufacturers of access points and repeaters — rather than primary routers — tend to choose it as a default. Primary routers typically claim the lower end of the range (such as 192.168.1.1 or 192.168.1.254), while secondary devices like the TRENDnet TPL-210AP and Hawking HW2R1 use higher addresses like 192.168.1.200 to avoid conflicts.

When you connect a laptop, phone, tablet, or smart TV to a network managed by a device at 192.168.1.200, your device receives its own private IP from the DHCP server — for example, 192.168.1.2, 192.168.1.3, and so on. These addresses allow the router or access point to direct internet traffic to the correct device. Every device on the network — including printers, smart speakers, and gaming consoles — gets its own private IP in the same subnet.

It is worth noting that only one device on a network should use 192.168.1.200 at any given time. If two devices share the same IP, an address conflict occurs, causing both devices to lose connectivity intermittently. If you suspect a conflict, log into your primary router and check the DHCP lease table, or manually assign a different static IP to one of the conflicting devices.

Related IP Addresses in the 192.168.1.x Subnet

The 192.168.1.0/24 subnet is home to several other commonly used default gateway addresses. If 192.168.1.200 is not your device's IP, one of the following may be:

• 192.168.1.1 — The most widely used default gateway in the world, used by TP-Link, D-Link, Netgear, Asus, and many others.
• 192.168.1.254 — Used by some BT Home Hub, 2Wire, and Westell routers as their default gateway.
• 192.168.0.1 — Common default for Netgear, D-Link, and some Linksys models.
• 192.168.2.1 — Used by some Cisco and Belkin routers.
• 192.168.8.1 — Default gateway for Huawei mobile Wi-Fi (MiFi) devices.
• 192.168.10.1 — Used by some Zyxel and Ubiquiti devices.
• 192.168.100.1 — Common for cable modems and some ISP-provided gateways.
• 10.0.0.1 — Used by Xfinity/Comcast gateways and some Apple AirPort devices.

If you are unsure which IP your device uses, the fastest method is to run ipconfig /all on Windows or ip route on Linux/macOS and look at the Default Gateway value. Alternatively, check the label on the back of your router or access point — manufacturers almost always print the default IP there.

Frequently Asked Questions About 192.168.1.200

What devices use 192.168.1.200 as their default IP?

The confirmed devices that use 192.168.1.200 as their default IP address include the TRENDnet TPL-210AP Powerline Access Point, the Linksys WPG54G Wireless-G Presentation Player, the Hawking Technology HW2R1 Smart Repeater, the Loopcomm LP-7316H wireless router, and certain UBIQCOM FTTH/XPON ONU gateway models. These are mostly secondary network devices (access points, repeaters, and powerline adapters) rather than primary routers.

Is 192.168.1.200 the same as my router's IP?

Not necessarily. If your primary router uses 192.168.1.1 or 192.168.0.1, then 192.168.1.200 likely belongs to a secondary device on your network — such as a TRENDnet powerline access point or a Hawking repeater. To confirm which device is at 192.168.1.200, open a browser, navigate to http://192.168.1.200, and see which brand's login page appears.

What is the default username and password for 192.168.1.200?

The default credentials depend on the device. For TRENDnet TPL-210AP and Loopcomm LP-7316H, use admin / admin. For Hawking HW2R1, use admin / 1234. For Linksys WPG54G, use admin with no password. For UBIQCOM devices, check the label on the unit. Always change these defaults after your first login to protect your network.

Can I change the IP address from 192.168.1.200 to something else?

Yes. Once logged into the admin panel at 192.168.1.200, navigate to the LAN or Network settings section and enter a new IP address. Only do this if you have a specific reason — such as resolving an IP conflict with another device on your 192.168.1.x network. If you change it, write down the new address, as you will need it for all future admin access.

Why can't I reach 192.168.1.200 from my computer?

The most common reasons are: you are not connected to the same network as the device, another device has been assigned the same IP address causing a conflict, your VPN is active and rerouting traffic, or the device's IP has been changed from the default. Run ipconfig /all on Windows to check your current default gateway, and make sure it matches 192.168.1.200 before troubleshooting further.

Is it safe to access 192.168.1.200?

Yes. Because 192.168.1.200 is a private RFC 1918 address, it is only accessible from within your local network. No one on the internet can reach it directly. However, you should still protect the admin panel with a strong, unique password to prevent unauthorized access from anyone connected to your Wi-Fi.