192.168.1.2 Admin Login

Several router and wireless access point manufacturers use 192.168.1.2 as their default IP address. Among the most notable brands are ZyXEL, EnGenius, DrayTek, Fortinet, and Planet, among others. It is used as a private IPv4 network address and serves as the router or access point gateway for local network administration. Because 192.168.1.2 sits in the same 192.168.1.x /24 subnet as the more widely known 192.168.1.1, it is particularly common among wireless access points and secondary network devices that operate alongside a primary router. Only one device on your network should be assigned 192.168.1.2 at any time to avoid IP address conflicts. Other common default gateways in the same subnet include 192.168.1.1, 192.168.1.254, and 192.168.0.1.

How to Access 192.168.1.2

To reach your router or access point's admin console, open any web browser and type http://192.168.1.2 directly into the address bar — not the search bar — and press Enter. You should be presented with a login page asking for a username and password. For most devices that use 192.168.1.2 as their default IP, the credentials are:

• Username: admin  |  Password: admin
• Username: admin  |  Password: (leave blank)
• Username: admin  |  Password: password
• Username: admin  |  Password: 1234

If you are accessing a ZyXEL NWA or WAC series access point, the default password is typically 1234. For EnGenius ECB or ESR series devices, the default is admin / admin. For DrayTek VigorAP models, try admin / admin as well. Always check the label on the bottom or back of your device for the exact factory credentials before attempting to log in.

Because 192.168.1.2 is a private IPv4 address, it is only reachable from within your local network. You must be connected to the same Wi-Fi network or plugged in via an Ethernet cable to access the admin panel at this address.

If You Can't Access 192.168.1.2

If typing http://192.168.1.2 into your browser returns an error or a blank page, there are a few things you should check before assuming the address is wrong:

1. Confirm your connection: Make sure your computer, phone, or tablet is connected to the same network as the device you're trying to reach. You cannot access 192.168.1.2 from outside your home or office network.
2. Check your gateway address: Open the Command Prompt on Windows (Start > type cmd > Enter) and run ipconfig /all. On macOS or Linux, open Terminal and run ip route or netstat -nr. Look for the Default Gateway value. If it shows something other than 192.168.1.2, that is your actual router IP.
3. Try HTTP, not HTTPS: Some browsers auto-redirect to HTTPS. Make sure you are using http://192.168.1.2 (not https://). ZyXEL and EnGenius access points in particular may not have HTTPS enabled by default.
4. Restart the device: Power-cycle your router or access point by unplugging it for 30 seconds and plugging it back in. Wait for it to fully boot before trying again.
5. Disable VPN or proxy: If you have a VPN or proxy active on your device, it may prevent access to local IP addresses. Temporarily disable it and try again.

If none of the above works, check our guide to find your router IP address for more detailed steps.

Router Brands That Use 192.168.1.2

Unlike the more universal 192.168.1.1, the address 192.168.1.2 is used by a more specific set of manufacturers — primarily for wireless access points, enterprise-grade networking gear, and ADSL/fiber routers sold in certain regions. Here is a breakdown of the confirmed brands and models:

• ZyXEL: A large number of ZyXEL NWA and WAC series wireless access points use 192.168.1.2 as their static default IP. This includes models such as the NWA1100, NWA1100-N, NWA1123-AC, NWA1123-NI (v1 and v2), NWA3163, NWA3560-N, NWA5123-ACHD, NWA570N, NWA-3160, NWA-3166, NWA-3550, G-3000H, G-570S (v1 and v2), G-570U, NBG6604, PLA4231, and PLA450 v2. ZyXEL uses 192.168.1.2 specifically for standalone access point mode so the device does not conflict with the primary router at 192.168.1.1.
• EnGenius: Several EnGenius access points and routers default to 192.168.1.2, including the ECB-9500, ECB9500, ERB9250, and ESR-9710. These are popular in small business and prosumer deployments.
• DrayTek: The DrayTek VigorAP-810 uses 192.168.1.2 as its default management IP address, making it accessible right out of the box when connected to a network where 192.168.1.1 is already in use.
• Fortinet: Several FortiAP wireless access point models — including the FAP-210B, FAP-112B, FAP-14C, FAP-221C, and FortiAP-210B — use 192.168.1.2 as their default IP for initial configuration.
• Planet: Planet's FRT-series routers, including the FRT-401, FRT-401N, FRT-401NS15, FRT-401S15, FRT-405, and FRT-405N, all use 192.168.1.2 as their default gateway address.
• Senao: Senao access points including the ECB-1220R, ECB-8610S, ECB9500, and ERB9250 use 192.168.1.2 as their default IP.
• Davolink: The Davolink DV-201AM ADSL modem/router uses 192.168.1.2 as its default login address.
• Airnet: The Airnet AWR014G8 Wireless router uses 192.168.1.2 as its default IP with admin/admin credentials.
• Rosewill: The Rosewill RNX-N4 wireless router uses 192.168.1.2 as its default gateway.
• Zinwell: The Zinwell PWQ-5121 uses 192.168.1.2 with root/root as default credentials.

Changing Your Router's Password at 192.168.1.2

Once you have successfully logged into your device at 192.168.1.2, one of the first things you should do is change the default admin password. Leaving the factory default password in place makes your network vulnerable to unauthorized access — especially since default credentials like admin/admin or admin/1234 are publicly known.

To change your password, follow these steps after logging in:

1. Navigate to the Administration, System, or Management section of the admin panel (the exact label varies by brand and model).
2. Look for a Password, Admin Password, or Change Password option.
3. Enter your current password, then type your new password twice to confirm it.
4. Click Save or Apply to store the changes.

For ZyXEL NWA/WAC access points, go to Maintenance > User Account to update the admin password. For EnGenius devices, navigate to Management > Admin. For DrayTek VigorAP models, go to System Maintenance > Administrator Password. For Fortinet FortiAP units, use the CLI or the FortiGate controller interface to update credentials. Always use a strong, unique password that combines uppercase and lowercase letters, numbers, and special characters.

Router Username and Password List

Factory Reset Procedures for Devices Using 192.168.1.2

If you have forgotten your admin password or can no longer access the panel at 192.168.1.2, a factory reset will restore the device to its original settings — including the default IP address and credentials. Here is how to perform a factory reset on the most common brands that use this IP:

ZyXEL NWA / WAC Series Access Points

Locate the RESET button on the back or bottom of your ZyXEL device. Using a pin or paperclip, press and hold the RESET button for more than 5 seconds until the PWR LED begins to flash. Release the button and wait for the device to reboot. Once it restarts, the IP address will return to 192.168.1.2 and the password will reset to 1234. You can also reset via the web interface by going to Maintenance > Reboot and selecting Reset to Factory Default.

EnGenius ECB / ESR Series

With the EnGenius device powered on, press and hold the RESET button (usually a small pinhole on the back panel) for approximately 10 seconds until the LEDs flash. The device will reboot and restore its default settings, including the 192.168.1.2 IP address and admin/admin credentials.

DrayTek VigorAP-810

To reset the DrayTek VigorAP-810, hold the recessed Factory Reset button for 5 seconds until the ACT LED begins flashing rapidly. Release the button and allow the device to reboot. Alternatively, log into the web interface and navigate to System Maintenance > Reboot System, then select Using factory default configuration and click Reboot.

Fortinet FortiAP

For FortiAP devices, you can reset to factory defaults by pressing and holding the RESET button for 10 seconds while the device is powered on. The device will reboot with factory settings. Alternatively, from the FortiGate controller, you can issue a factory reset command through the FortiAP management interface. After reset, the default IP reverts to 192.168.1.2 and the admin password is cleared or reset to the factory default.

Planet FRT Series

Press and hold the RESET button on the Planet FRT router for 10 seconds while the device is powered on. The device will reboot and restore all settings to factory defaults, including the 192.168.1.2 default gateway and admin/admin login credentials.

What Is 192.168.1.2 and How Does It Work?

192.168.1.2 is a private IPv4 address that belongs to the Class C private address range defined by RFC 1918. The full Class C private range spans from 192.168.0.0 to 192.168.255.255, and 192.168.1.2 falls within the commonly used 192.168.1.0/24 subnet. This subnet supports up to 254 usable host addresses (192.168.1.1 through 192.168.1.254), making it ideal for home and small business networks.

When a manufacturer assigns 192.168.1.2 as the default gateway of a device, it means that address is the entry point to the device's web-based administration interface. Every other device that connects to your network — laptops, smartphones, smart TVs, printers — receives its own unique private IP address, typically assigned automatically by the router's DHCP server. For example:

• Your router or access point: 192.168.1.2
• Your laptop: 192.168.1.3
• Your smartphone: 192.168.1.4
• Your smart TV: 192.168.1.5

These private addresses are not visible on the public internet. They exist only within your local network. When your devices communicate with the outside world, your router translates these private IPs into your single public IP address using a process called Network Address Translation (NAT).

It is worth noting that 192.168.1.2 is particularly popular among wireless access points (as opposed to full routers) because it avoids conflicting with the primary router, which typically occupies 192.168.1.1. This design allows the access point to be managed independently while still operating on the same subnet.

Related IP Addresses in the 192.168.1.x Subnet

The 192.168.1.0/24 subnet is one of the most widely used private network ranges in the world. Several IP addresses within this subnet are commonly assigned as default gateways by various router and networking equipment manufacturers. If 192.168.1.2 is not your device's default IP, one of the following addresses in the same subnet may be:

• 192.168.1.1 — The most common default gateway in the 192.168.1.x range, used by Linksys, TP-Link, Cisco, ASUS, and many others.
• 192.168.1.2 — Used by ZyXEL access points, EnGenius, DrayTek VigorAP, Fortinet FortiAP, and Planet routers.
• 192.168.1.254 — Common among some DSL modems and ISP-provided gateways, particularly in Europe.
• 192.168.1.100 — Sometimes used as a static IP for network-attached storage (NAS) devices or secondary access points.
• 192.168.1.10 — Occasionally used by enterprise switches and managed network devices.

Understanding the layout of your 192.168.1.x subnet helps you avoid IP conflicts and manage your network more effectively. If you are unsure which IP your device uses, check the label on the bottom of the device, consult the user manual, or use the ipconfig /all command on Windows (or ip route on Linux/macOS) to identify your current default gateway.

Frequently Asked Questions About 192.168.1.2

What is 192.168.1.2 used for?

192.168.1.2 is a private IP address used as the default gateway for several router and wireless access point brands, including ZyXEL, EnGenius, DrayTek, Fortinet, and Planet. You use it to access the admin panel of your networking device by typing http://192.168.1.2 into your browser. From there, you can configure Wi-Fi settings, change passwords, set up port forwarding, and manage connected devices.

Is 192.168.1.2 the same as 192.168.1.1?

No. While both addresses belong to the same 192.168.1.0/24 subnet, they are distinct IP addresses assigned to different devices. 192.168.1.1 is the more common default gateway used by brands like Linksys, TP-Link, and ASUS, while 192.168.1.2 is specifically used by ZyXEL NWA/WAC access points, EnGenius ECB/ESR devices, DrayTek VigorAP, Fortinet FortiAP, and Planet FRT routers. If you type 192.168.1.2 and get no response, your device may be using 192.168.1.1 instead.

Why can't I access 192.168.1.2?

There are several reasons you might not be able to reach 192.168.1.2: you may not be connected to the correct network, your device's default IP may have been changed, or there may be a browser issue (try using HTTP instead of HTTPS). Run ipconfig /all on Windows to confirm your actual default gateway. If the gateway is different, use that IP instead. If you've forgotten the password, perform a factory reset as described in the section above to restore 192.168.1.2 as the default.

What is the default username and password for 192.168.1.2?

The most common default credentials for devices using 192.168.1.2 are admin / admin. However, this varies by brand: ZyXEL NWA/WAC access points typically use admin / 1234, Fortinet FortiAP devices may have no password set by default, and Zinwell devices use root / root. Always check the label on your device or its user manual for the exact factory credentials.

Can I assign 192.168.1.2 to my own device?

Yes. Since 192.168.1.2 is a private IP address within the 192.168.1.0/24 subnet, you can manually assign it to any device on your network — such as a computer, printer, or NAS — as a static IP address. However, make sure no other device on your network is already using 192.168.1.2 (for example, a ZyXEL or EnGenius access point), as this would cause an IP address conflict and disrupt connectivity for both devices.

Is 192.168.1.2 a public or private IP address?

192.168.1.2 is a private IP address. It is part of the 192.168.0.0/16 private address block defined by RFC 1918 and is not routable on the public internet. This means it can only be used within a local area network (LAN) and is completely invisible to external servers and websites. Your public IP address — the one websites see when you browse the internet — is assigned by your Internet Service Provider (ISP) and is entirely separate from 192.168.1.2.