192.168.1.14 Admin Login

The IP address 192.168.1.14 is primarily associated with HP ProCurve wireless access point devices, most notably the HP ProCurve Wireless Access Point 10ag (models J9140A and J9141A). HP officially documents 192.168.1.14 as the factory default IP address for these devices, making it a well-defined and brand-specific address within the 192.168.1.0/24 subnet. While it is far less common as a default gateway than addresses like 192.168.1.1 or 192.168.0.1, 192.168.1.14 serves a very specific and documented role in HP's ProCurve networking product line.

Beyond its HP ProCurve association, 192.168.1.14 is also a valid Class C private IPv4 address that any router or DHCP server operating on the 192.168.1.0/24 subnet can assign to a connected device — such as a laptop, smartphone, smart TV, or printer. It falls within the IANA-reserved private address range of 192.168.0.0 to 192.168.255.255, meaning it is never routable on the public internet and is exclusively used within local area networks (LANs).

How to Access 192.168.1.14

To access the admin panel at 192.168.1.14, open your preferred web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.1.14 directly into the address bar. Do not use a search engine to navigate to this address; you must type it directly into the URL bar and press Enter. This will load the router or access point's web-based management interface.

For the HP ProCurve Wireless AP 10ag, the factory default credentials are:

• Username: admin
• Password: password

Once logged in, you will be presented with the HP ProCurve web interface, which is a web-only management console. From here you can configure wireless radio settings, change the SSID, set security protocols (WPA/WPA2), adjust IP address settings, monitor connected clients, and manage firmware updates. Note that on a freshly reset HP ProCurve AP 10ag, the wireless radios are disabled by default — you will need to navigate to the Advanced Settings section to enable them before the device begins broadcasting a Wi-Fi signal.

If 192.168.1.14 is being used as a DHCP-assigned address on your home or office network (i.e., your router assigned it to one of your devices), then typing it into a browser will not open a router admin panel. In that case, you should find your actual router's gateway IP — typically 192.168.1.1 — and use that to access your router's settings.

If You Can't Access 192.168.1.14

If entering http://192.168.1.14 into your browser returns an error, a blank page, or a "site can't be reached" message, there are several possible explanations and fixes:

• Your device is not on the same subnet: To communicate with 192.168.1.14, your computer or device must be on the 192.168.1.0/24 network. If your machine has an IP address in a different range (e.g., 192.168.0.x or 10.0.0.x), it will not be able to reach 192.168.1.14 directly. Connect your computer to the same network as the HP ProCurve AP or device using this IP.
• The IP has been changed: If someone previously configured the HP ProCurve AP 10ag and changed its default IP address, 192.168.1.14 will no longer work. You will need to perform a factory reset to restore the default IP.
• IP address conflict: If another device on your network has been manually assigned 192.168.1.14, there will be a conflict and neither device will respond reliably. Check your DHCP lease table to identify conflicts.
• Firewall or browser issue: Disable any browser extensions or VPNs that might block local network access, and try a different browser.

To confirm your current gateway address, open the Command Prompt on Windows (Start > Run > cmd) and type ipconfig /all. On macOS or Linux, open Terminal and type netstat -nr | grep default. The result will show your actual default gateway. If it differs from 192.168.1.14, check our guide to find your router IP address.

HP ProCurve Wireless AP 10ag — Factory Reset Procedure

If you have forgotten the admin password for your HP ProCurve Wireless AP 10ag, or if the device is no longer responding at 192.168.1.14, you can restore it to factory defaults using the hardware reset button. Here is the official procedure:

1. Ensure the device is powered on. The HP ProCurve AP 10ag must be connected to power before you begin the reset process.
2. Locate the Reset to Default button. This is a small recessed button found on the back or underside of the access point. You will need a pointed object such as a ballpoint pen tip, a straightened paperclip, or a toothpick to press it.
3. Press and hold the Reset button for more than 5 seconds. According to HPE's official documentation, holding the button for over five seconds initiates the factory reset. The LEDs on the device will flash to indicate the reset is in progress.
4. Wait for the device to reboot. The AP 10ag will restart automatically. Once it comes back online, all settings — including the IP address — will be restored to factory defaults.
5. Reconnect and log in. After the reset, the device's IP address will return to 192.168.1.14 with the subnet mask /24. Use the default credentials (username: admin, password: password) to log back in via http://192.168.1.14.

Important: A factory reset will erase all custom configurations, including your SSID, wireless security settings, and any static IP assignments. Make sure to back up your configuration before resetting if possible. After resetting, remember to immediately change the default password to something strong and unique to protect your network.

Changing Your Password at 192.168.1.14

Keeping the default password on any network device is a serious security risk. If your HP ProCurve AP 10ag or any device accessible at 192.168.1.14 still uses the factory default credentials (admin / password), you should change it immediately. Here's how:

1. Log in to the admin panel at http://192.168.1.14 using your current credentials.
2. Navigate to the Administration or Management section of the web interface.
3. Look for the Change Password or User Accounts option.
4. Enter your current password, then type your new password twice to confirm it.
5. Click Apply or Save to commit the change.

Choose a password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and special characters. Avoid using easily guessable information such as your name, address, or the word "password". Once changed, store your new password in a secure password manager so you don't lose access to the 192.168.1.14 admin panel in the future.

Router Username and Password List

What Kind of IP Address is 192.168.1.14?

192.168.1.14 is a Class C private IPv4 address, belonging to the 192.168.0.0/16 private address block defined by RFC 1918. Specifically, it sits within the 192.168.1.0/24 subnet, which supports up to 254 usable host addresses ranging from 192.168.1.1 to 192.168.1.254. The subnet mask for this range is 255.255.255.0.

Because it is a private address, 192.168.1.14 is not routable on the public internet. It can only be used within a local area network (LAN). Millions of home and business networks around the world use the 192.168.1.0/24 subnet, which means 192.168.1.14 is a very commonly encountered address — though it is typically assigned dynamically by a DHCP server rather than used as a fixed gateway.

In the context of the HP ProCurve Wireless AP 10ag, 192.168.1.14 is used as a static management IP address, meaning the device always listens on this address for incoming web management connections. This is different from a default gateway (like 192.168.1.1), which routes traffic between the local network and the internet. The AP 10ag uses 192.168.1.14 purely for device administration, not for routing internet traffic.

Other devices on the same 192.168.1.0/24 network that receive DHCP-assigned addresses may also be assigned 192.168.1.14 if the DHCP pool includes it. To avoid conflicts with the HP ProCurve AP 10ag, you should either exclude 192.168.1.14 from your DHCP pool or configure a DHCP reservation for the AP's MAC address.

Related IP Addresses in the 192.168.1.0/24 Subnet

The 192.168.1.0/24 subnet is one of the most widely used private network ranges in the world. If you are working with 192.168.1.14, you may also encounter the following commonly used IP addresses within the same subnet and beyond:

• 192.168.1.1 — The most common default gateway for routers from TP-Link, ASUS, Netgear, D-Link, Linksys, and many others. This is the address you most likely use to access your home router's admin panel.
• 192.168.1.254 — Used as the default gateway by some DSL modems and routers, particularly older models from 2Wire, Speedtouch, and certain ISP-provided equipment.
• 192.168.0.1 — Another extremely common default gateway, used by Netgear, D-Link, and other brands on the 192.168.0.0/24 subnet.
• 192.168.2.1 — Default gateway used by some Belkin and SMC routers.
• 192.168.8.1 — Commonly used by Huawei mobile Wi-Fi hotspot devices and some Huawei routers.
• 192.168.10.1 — Used by some Zyxel and Motorola devices as their default management IP.
• 192.168.100.1 — Often used by cable modems and ISP-provided gateways, particularly those from Motorola and Huawei.
• 10.0.0.1 — A default gateway used on the 10.0.0.0/8 private network range, common in Xfinity/Comcast gateways and some Cisco devices.

Understanding where 192.168.1.14 fits within this broader landscape of private IP addresses helps you navigate your network more confidently, whether you're troubleshooting connectivity issues, setting up a new device, or securing your wireless network.

Frequently Asked Questions About 192.168.1.14

What router uses 192.168.1.14 as its default IP address?

The primary device that uses 192.168.1.14 as its factory default IP address is the HP ProCurve Wireless Access Point 10ag, available in models J9140A (NA version) and J9141A. HP officially documents this IP as the default management address for these access points. If you are not using an HP ProCurve AP 10ag, then 192.168.1.14 is most likely a DHCP-assigned address given to one of your connected devices by your router.

What are the default login credentials for 192.168.1.14?

For the HP ProCurve Wireless AP 10ag, the factory default credentials are username: admin and password: password. These are the credentials you use when logging into the web interface at http://192.168.1.14 for the first time or after a factory reset. You should change these immediately after your first login to protect your device from unauthorized access.

Why can't I access 192.168.1.14 in my browser?

There are several reasons you might not be able to reach 192.168.1.14. First, make sure your computer is connected to the same 192.168.1.0/24 network as the device using this IP. Second, check that no other device on your network has been assigned the same address, which would cause a conflict. Third, if you are trying to access an HP ProCurve AP 10ag and the IP has been changed from the default, you will need to perform a factory reset to restore 192.168.1.14. Finally, ensure you are typing the address directly into the browser's URL bar — not into a search engine.

Is 192.168.1.14 a public or private IP address?

192.168.1.14 is a private IP address. It belongs to the Class C private address range defined by RFC 1918 (192.168.0.0 – 192.168.255.255). This means it cannot be accessed from the public internet and is only usable within a local network. Your internet service provider (ISP) will never assign 192.168.1.14 as your public IP address.

Can I assign 192.168.1.14 to any device on my network?

Yes, you can assign 192.168.1.14 to any device on your 192.168.1.0/24 network, either statically or via a DHCP reservation. However, if you also have an HP ProCurve Wireless AP 10ag on the same network using 192.168.1.14 as its default IP, assigning this address to another device will cause an IP address conflict. In that case, you should either change the AP's management IP or exclude 192.168.1.14 from your DHCP pool.

How do I find out if 192.168.1.14 is my router's IP or a device IP?

Open a Command Prompt on Windows and run ipconfig /all, or open Terminal on macOS/Linux and run netstat -nr | grep default. Look at the Default Gateway field. If it shows 192.168.1.14, then that is your router or access point's management IP. If the gateway shows a different address (like 192.168.1.1), then 192.168.1.14 is simply a device IP assigned by your router's DHCP server.