192.168.1.102 Admin Login

192.168.1.102 is a private IPv4 address belonging to the Class C range of the 192.168.1.0/24 subnet. It is used as the default gateway IP address by a select number of router and networking device manufacturers. Most notably, the Get Box II (by the French ISP Get) and the Planet FRT-401S15 Internet Fiber Router ship with 192.168.1.102 as their factory-configured LAN IP address. While far less common than 192.168.1.1 or 192.168.0.1, this address is a fully valid private IP that allows you to reach your router's admin panel directly from any browser on the same network. Because it sits within the 192.168.1.x block, it is also frequently assigned by DHCP servers as a dynamic address to client devices such as laptops, smartphones, and smart-home gadgets connected to routers whose gateway is 192.168.1.1 or 192.168.1.254.

How to Access 192.168.1.102

To reach your router's admin panel at 192.168.1.102, open any web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.1.102 directly into the address bar. Do not type it into a search engine, as that will return search results instead of your router's login page. Press Enter and you should see a login prompt within a few seconds.

Before you attempt to log in, make sure your device is connected to the same network as the router — either via an Ethernet cable plugged into one of the router's LAN ports, or via Wi-Fi. If you are using a Get Box II, the default credentials are username: home and password: home. If you are using a Planet FRT-401S15, try username: admin and password: admin as the factory defaults. Always check the label on the underside or rear of your device for the exact credentials printed by the manufacturer, as some units ship with unique passwords.

Once logged in, you will have full access to your router's configuration dashboard, where you can manage wireless settings, set up port forwarding, configure a guest network, update firmware, and adjust firewall rules — all specific to your device at 192.168.1.102.

If You Can't Access 192.168.1.102

If typing http://192.168.1.102 into your browser produces an error, a blank page, or redirects you elsewhere, there are several likely causes to investigate:

• Wrong default gateway: Not every router uses 192.168.1.102. Open a Command Prompt on Windows (Start > cmd) and run ipconfig /all, then look for the Default Gateway value. On macOS or Linux, run netstat -nr or check System Preferences > Network. If the gateway shown is different — for example 192.168.1.1 or 192.168.1.254 — use that address instead.
• IP address conflict: If both your modem (supplied by your ISP) and your router are configured to use 192.168.1.102, an address conflict will prevent either device from responding correctly. Change one device's LAN IP to resolve the conflict.
• Address was changed previously: Someone may have manually changed the router's LAN IP from 192.168.1.102 to something else. In that case, you will need to either find the new IP via ipconfig /all or perform a factory reset to restore 192.168.1.102 as the default.
• Browser cache or HTTPS redirect: Clear your browser cache and make sure you are using http:// (not https://) before the IP address, as most router admin panels do not use SSL by default.
• Device not on the same network: If your computer is connected to a different network or is using a VPN, it will not be able to reach 192.168.1.102. Disconnect from any VPN and ensure you are on the correct local network.

If none of the above resolves the issue, consult our guide to finding your router IP address for step-by-step instructions.

Router Brands That Use 192.168.1.102

Based on confirmed manufacturer documentation, the following brands and models are known to ship with 192.168.1.102 as their default gateway:

• Get (Box II) — The Get Box II is an ISP-provided home gateway distributed by the French cable operator Get. It uses 192.168.1.102 as its factory LAN IP. The default login credentials are username: home / password: home. The admin panel gives you access to Wi-Fi settings, DHCP configuration, port forwarding, and parental controls.
• Planet Technology (FRT-401S15) — The Planet FRT-401S15 is a wired/wireless Internet Fiber Router designed for FTTH and IPTV applications. It features a 100Base-BX SC fiber WAN interface and a 4-port Fast Ethernet switch. Planet Technology ships this model with 192.168.1.102 as the default LAN IP. Default credentials are typically username: admin / password: admin.

Outside of these confirmed models, 192.168.1.102 is also widely encountered as a DHCP-assigned client address on networks where the router gateway is set to 192.168.1.1, 192.168.1.254, or another address in the same /24 subnet. In those cases, 192.168.1.102 belongs to a connected device — not the router itself — and you should not expect a router login page at that address.

Changing Your Router's Password at 192.168.1.102

Keeping the default password on your router is one of the most common and dangerous security mistakes you can make. If your router's admin panel is accessible at 192.168.1.102, you should change the admin password as soon as possible after your initial setup.

To change the password on a Get Box II, log in at http://192.168.1.102 using the default credentials (home / home), then navigate to the Administration or System section of the dashboard. Look for a Change Password or Admin Password option and enter your new password twice to confirm. Choose a strong password of at least 12 characters, mixing uppercase letters, lowercase letters, numbers, and symbols.

On a Planet FRT-401S15, log in at 192.168.1.102 with admin / admin, then go to Management > Admin or System Tools > Password to update your credentials. After saving, you will be prompted to log in again with the new password.

In addition to changing the admin password, you should also update your Wi-Fi password (WPA2 or WPA3) and your Wi-Fi network name (SSID) to something that does not reveal your router brand or model, as this information can make it easier for attackers to target known vulnerabilities.

Router Username and Password List

Factory Reset: Get Box II and Planet FRT-401S15

If you have forgotten your admin password or your router is behaving unexpectedly, a factory reset will restore all settings — including the default IP address 192.168.1.102 and the original login credentials — to their out-of-box state. Be aware that a factory reset will erase all custom configurations, including your Wi-Fi name, Wi-Fi password, port forwarding rules, and any other changes you have made.

Get Box II Factory Reset

1. Make sure the Get Box II is powered on and all indicator LEDs are stable.
2. Locate the Reset button on the rear panel of the device. It is typically recessed to prevent accidental presses.
3. Use a straightened paperclip or a SIM ejector tool to press and hold the Reset button for at least 10–15 seconds.
4. Release the button when the LEDs begin to flash or change color, indicating the reset process has started.
5. Wait approximately 2–3 minutes for the device to fully reboot and restore factory defaults.
6. Once the device is back online, reconnect to its default Wi-Fi network and navigate to http://192.168.1.102 using the default credentials home / home.

Planet FRT-401S15 Factory Reset

1. Ensure the router is powered on.
2. Locate the Reset button on the rear panel.
3. Press and hold the Reset button for 10 seconds using a pin or paperclip until the PWR LED flashes.
4. Release the button and allow the router to reboot — this typically takes 60–90 seconds.
5. After the reboot, the router's LAN IP will be restored to 192.168.1.102 and the admin credentials will revert to admin / admin.
6. Reconnect your device to the router's network and open http://192.168.1.102 to begin reconfiguration.

What Is 192.168.1.102 as a Private IP Address?

192.168.1.102 is a private IPv4 address defined by RFC 1918. It belongs to the Class C private address block 192.168.0.0 – 192.168.255.255, which is reserved exclusively for use within local area networks (LANs). Devices using addresses in this range cannot communicate directly with the public internet — all outbound traffic must pass through a router that performs Network Address Translation (NAT), substituting the private IP with the router's public IP before forwarding packets to the internet.

Within the 192.168.1.0/24 subnet, there are 254 usable host addresses: from 192.168.1.1 to 192.168.1.254. The address 192.168.1.102 sits in the middle of this range and can be assigned to any device on the network — whether it is the router itself (as a default gateway), a desktop computer, a laptop, a smartphone, a smart TV, a printer, or a network-attached storage (NAS) device.

When 192.168.1.102 is used as a router's default gateway (as with the Get Box II and Planet FRT-401S15), every other device on the network uses it as the exit point for all internet-bound traffic. When it is assigned by a DHCP server as a client address, it simply identifies one specific device on the local network. In either case, the address is invisible to the outside world and is only meaningful within your home or office network.

Other commonly used addresses in the same subnet include 192.168.1.1 (the most popular default gateway for home routers), 192.168.1.254 (used by many DSL modems and ISP-provided gateways), and addresses like 192.168.1.2 through 192.168.1.100, which are typically reserved for DHCP client assignment.

Related IP Addresses in the 192.168.1.x Subnet

If 192.168.1.102 is not the correct address for your router, the following related IPs in the same subnet or nearby ranges may be what you are looking for. These are among the most commonly used default gateway addresses for home and small-office routers:

• 192.168.1.1 — The most widely used default gateway address in the world, used by Linksys, TP-Link, Cisco, Tenda, and many others.
• 192.168.1.254 — Common default gateway for BT Home Hubs, some D-Link models, and various DSL modems.
• 192.168.0.1 — Used by Netgear, D-Link, and several other major brands as their default LAN IP.
• 192.168.2.1 — Default gateway for some Cisco and Belkin routers.
• 192.168.8.1 — Used by Huawei routers and mobile Wi-Fi hotspots.
• 192.168.10.1 — Default gateway for some Zyxel and Ubiquiti devices.
• 192.168.100.1 — Common default IP for cable modems and some ISP-provided gateways.
• 10.0.0.1 — Used by Xfinity/Comcast gateways and some Apple AirPort devices.

If none of these match your router's gateway, use the ipconfig /all command on Windows or netstat -nr on macOS/Linux to find the exact IP address your router is currently using.

Frequently Asked Questions About 192.168.1.102

Which routers use 192.168.1.102 as their default IP?

The confirmed routers that use 192.168.1.102 as their factory default gateway are the Get Box II (distributed by the French ISP Get) and the Planet FRT-401S15 Internet Fiber Router. Outside of these models, 192.168.1.102 is most commonly encountered as a DHCP-assigned client address on networks where the router gateway is 192.168.1.1 or another address in the 192.168.1.x range.

What are the default login credentials for 192.168.1.102?

For the Get Box II, the default username is home and the default password is home. For the Planet FRT-401S15, the default username is admin and the default password is admin. If neither set of credentials works, check the label on the bottom or rear of your device, or perform a factory reset to restore the original defaults.

Why is my device getting 192.168.1.102 as its IP address?

If your computer, phone, or other device has been assigned 192.168.1.102, it means your router's DHCP server has dynamically allocated that address to your device. This is completely normal. Your router's gateway address is likely 192.168.1.1 or 192.168.1.254, not 192.168.1.102 itself. To confirm, run ipconfig /all on Windows and check the Default Gateway field.

Can two devices on my network share the IP 192.168.1.102?

No. Within any single network, each device must have a unique IP address. If two devices are both assigned 192.168.1.102 — whether statically or through a DHCP misconfiguration — an IP address conflict will occur, causing both devices to lose network connectivity intermittently. To resolve this, assign a static IP outside the DHCP range to any device that requires a fixed address, or let the DHCP server manage all assignments automatically.

Is 192.168.1.102 safe to use on my network?

Yes. As a private IP address, 192.168.1.102 is completely safe and is not accessible from the public internet. However, if your router's admin panel is reachable at 192.168.1.102, you should always change the default admin password (especially the home/home default on the Get Box II) to prevent unauthorized access from other devices on your local network.

How do I set 192.168.1.102 as a static IP for a device on my network?

To assign 192.168.1.102 as a permanent static IP to a specific device, you have two options. First, you can configure it directly on the device itself — on Windows, go to Network Settings > Adapter Properties > IPv4 Settings and enter 192.168.1.102 as the IP, your router's address as the gateway, and your preferred DNS servers. Second, you can use your router's DHCP reservation feature (sometimes called Address Binding or Static DHCP) to permanently assign 192.168.1.102 to a specific device's MAC address. Log in to your router at its gateway IP and look for this option under the DHCP or LAN settings menu.