192.168.0.200 Admin Login

The IP address 192.168.0.200 is a private Class C IPv4 address that sits within the 192.168.0.0/24 subnet. It is most notably used by Netgear as the factory-default management IP for the ME101 802.11b Wireless Ethernet Bridge — a device designed to connect wired-only equipment to a wireless network. Beyond that specific hardware assignment, 192.168.0.200 is widely used as a statically assigned or DHCP-reserved address on home and small-office networks that use the 192.168.0.x address range. Because it sits at the higher end of the subnet, network administrators often reserve addresses like 192.168.0.200 for printers, NAS drives, IP cameras, smart home hubs, and other devices that benefit from a predictable, permanent address. Other commonly referenced gateways in the same family include 192.168.0.1 and 192.168.1.254.

How to Access 192.168.0.200

To reach the admin panel at 192.168.0.200, open any web browser on a device that is connected to the same network and type http://192.168.0.200 directly into the address bar — do not use a search engine. If your device is a Netgear ME101 Wireless Ethernet Bridge, the browser will load the ME101 configuration utility login page immediately. For other routers or network devices that have been manually assigned this address, you will see whichever admin interface belongs to that specific hardware.

Before you attempt to log in, make sure you are connected to the correct network. If you are on Wi-Fi, confirm that your device is associated with the router or access point whose LAN range includes 192.168.0.200. If you are using a wired connection, plug your Ethernet cable into one of the router's LAN ports (not the WAN/Internet port). Once the login page loads, enter the default credentials printed on your device's label, or try the common defaults listed in the table above.

If You Cannot Access 192.168.0.200

If typing http://192.168.0.200 into your browser returns an error or a blank page, work through the following checks before assuming the address is wrong:

• Verify your gateway: On Windows, open Command Prompt (Start > type cmd > press Enter) and run ipconfig /all. Look for the Default Gateway line under your active adapter. If it shows something other than 192.168.0.200 — for example 192.168.0.1 — then 192.168.0.200 is not your router's management address; it may instead be a static IP assigned to another device on the network.
• Check your connection: Ensure the Ethernet cable is seated firmly in the LAN port, or that your Wi-Fi is connected to the right SSID. A connection to a guest network or a neighbour's network will prevent you from reaching 192.168.0.200.
• Disable VPN or proxy: Active VPN clients and browser proxies can redirect traffic away from local addresses. Temporarily disable them and try again.
• Try a different browser or incognito mode: Cached redirects or HTTPS-only settings in some browsers can block access to local IP addresses. Open a private/incognito window and navigate to http://192.168.0.200 (HTTP, not HTTPS).
• Ping the address: In Command Prompt or Terminal, run ping 192.168.0.200. If you receive replies, the device is reachable and the issue is likely browser-related. If requests time out, the device may be offline or the IP may have been changed.

If none of the above resolves the issue, consult our guide on how to find your router's IP address.

Netgear ME101 — The Primary Device Using 192.168.0.200

The Netgear ME101 802.11b Wireless Ethernet Bridge is the most well-documented device that ships with 192.168.0.200 as its factory-default IP address. The ME101 was designed to give any wired Ethernet device — such as a desktop PC, gaming console, or set-top box — wireless connectivity without requiring a built-in Wi-Fi adapter. It bridges the wired device to an existing 802.11b wireless network.

To configure the ME101 using its default address, follow these steps:

1. Connect the ME101 to your computer using the included Ethernet crossover cable.
2. Power on the ME101 and wait for the status LEDs to stabilise.
3. Open your browser and navigate to http://192.168.0.200.
4. When prompted, enter the default username admin and the default password password.
5. Use the configuration utility to select your wireless network (SSID), set the security type, and enter your Wi-Fi passphrase.
6. Click Apply to save. The ME101 will reboot and join your wireless network.

Important note from Netgear's official documentation: If you have more than one ME101 on the same network, only one unit can retain the default address of 192.168.0.200. You must assign a unique IP to each additional unit to avoid address conflicts.

Factory Reset Procedure for Devices at 192.168.0.200

If you have forgotten the admin password for a device currently using 192.168.0.200, a factory reset will restore all settings — including the IP address and login credentials — to their factory defaults. The exact procedure depends on your hardware:

Netgear ME101

Locate the small recessed Reset button on the back panel of the ME101. With the device powered on, use a straightened paperclip or a similar thin object to press and hold the Reset button for approximately 10 seconds until the LEDs flash, indicating the reset is in progress. Release the button and allow the device to reboot. Once it restarts, the management IP will return to 192.168.0.200, and the credentials will revert to admin / password.

General Netgear Routers and Bridges

For other Netgear hardware that has been manually configured to use 192.168.0.200, Netgear's standard factory reset method applies: press and hold the Restore Factory Settings button on the rear of the device for 7 seconds using a paperclip. The Power LED will blink amber and then turn solid green when the reset is complete. After the reset, refer to the device label for the restored default IP and credentials.

Third-Party or Custom-Configured Devices

If 192.168.0.200 was manually assigned to a router from another brand — such as a TP-Link or D-Link unit — the factory reset button is typically found on the rear or bottom of the device. Hold it for 10–15 seconds with the device powered on. After the reset, the device will revert to its own manufacturer default IP (commonly 192.168.0.1 or 192.168.1.254), not 192.168.0.200.

Changing Your Password at 192.168.0.200

Keeping the default admin password on any device accessible at 192.168.0.200 is a significant security risk. Anyone connected to your local network can attempt to log in using well-known default credentials. To change your password, log in to the admin panel at http://192.168.0.200 and navigate to the Administration, Management, or System section — the exact label varies by device. Look for a Change Password or Admin Password field. You will typically be asked to enter the current password once and the new password twice for confirmation.

Choose a strong password that is at least 12 characters long and combines uppercase letters, lowercase letters, numbers, and symbols. Avoid using personal information such as your name, address, or date of birth. Once saved, write the new password down and store it in a secure location — if you lose it, you will need to perform a factory reset to regain access to the device at 192.168.0.200.

Router Username and Password List

What Is 192.168.0.200 as a Private IP Address?

192.168.0.200 is a private IPv4 address in the Class C range defined by RFC 1918. Addresses in the 192.168.0.0 – 192.168.255.255 block are reserved exclusively for use within private networks and are never routed across the public internet. This means that 192.168.0.200 can exist on millions of home and business networks simultaneously without any conflict, because each instance is isolated within its own local network.

Within the 192.168.0.0/24 subnet, the usable host range runs from 192.168.0.1 to 192.168.0.254, giving you up to 254 addressable devices. The address 192.168.0.200 sits near the upper end of this range, which is why network administrators often choose it — or addresses near it — for devices that need a fixed, predictable IP. Common examples include:

• Network-attached storage (NAS) drives — so you can always reach your files at the same address.
• IP cameras and security systems — so your recording software always knows where to connect.
• Smart home hubs and controllers — such as Home Assistant or SmartThings bridges.
• Network printers and scanners — so every computer on the network can find the printer without reconfiguration.
• Wireless ethernet bridges — such as the Netgear ME101, which uses 192.168.0.200 by default.

When a device is assigned 192.168.0.200 — either statically or via a DHCP reservation — every other device on the same 192.168.0.x network can communicate with it directly. The router (typically at an address like 192.168.0.1) acts as the gateway, forwarding traffic between the local network and the wider internet. The device at 192.168.0.200 itself does not need internet access to be reachable from within the LAN.

One important rule: only one device on a network should use 192.168.0.200 at any given time. If two devices share the same IP, both will experience connectivity problems — a situation known as an IP address conflict. Most modern operating systems will warn you when a conflict is detected, but the safest approach is to plan your address assignments carefully and keep a record of which device uses which IP.

Related IP Addresses in the 192.168.0.x Subnet

If 192.168.0.200 is already in use on your network, or if you are planning your address scheme, the following IP addresses in the same subnet are commonly referenced and may be relevant to your setup:

• 192.168.0.1 — The most widely used default gateway in the 192.168.0.x range, assigned by default to routers from Netgear, D-Link, TP-Link, and many others.
• 192.168.1.254 — A common alternative gateway used by routers from brands such as Billion and some ISP-supplied modems.
• 192.168.2.1 — Default gateway used by some Belkin and SMC routers, operating on the 192.168.2.x subnet.
• 192.168.8.1 — Default gateway for Huawei routers and mobile Wi-Fi hotspot devices.
• 192.168.10.1 — Used by certain Cisco and Ubiquiti devices as their default management address.
• 192.168.100.1 — Common default for cable modems and ISP-supplied gateways, particularly from Arris and Motorola.
• 10.0.0.1 — A Class A private address used as the default gateway by Xfinity/Comcast gateways and some Apple AirPort devices.

Understanding where 192.168.0.200 sits relative to these addresses helps you avoid conflicts and plan a clean, organised network. If your router's DHCP pool is set to distribute addresses from 192.168.0.100 to 192.168.0.200, for example, you should assign static IPs either below 192.168.0.100 or above 192.168.0.200 to prevent the DHCP server from handing out an address already in use by a statically configured device.

Frequently Asked Questions About 192.168.0.200

Which router brand uses 192.168.0.200 as its default IP?

The most confirmed brand is Netgear, specifically for the ME101 802.11b Wireless Ethernet Bridge. Netgear's own installation documentation confirms that 192.168.0.200 is the factory-default address for this device. Other routers and network devices may also appear at 192.168.0.200 if an administrator has manually assigned that address, but it is not a common factory default for mainstream routers from brands like TP-Link, D-Link, or Linksys.

Is 192.168.0.200 a valid IP address for my home network?

Yes. 192.168.0.200 is a fully valid private IPv4 address within the 192.168.0.0/24 subnet. You can assign it to any device on your home network — a printer, NAS, IP camera, or smart home hub — as long as no other device on the same network is already using it. It will never conflict with any public internet address because it is a reserved private range.

What is the default username and password for 192.168.0.200?

For the Netgear ME101, the default credentials are username admin and password password. For other devices that have been configured to use 192.168.0.200, check the label on the bottom or back of the device. Common fallback combinations across brands include admin/admin, admin/1234, and admin/(blank). If none of these work, a factory reset will restore the original defaults.

Why can't I access 192.168.0.200 in my browser?

The most common reasons are: (1) your device is not connected to the same network as the device at 192.168.0.200; (2) the device at that address is powered off or disconnected; (3) the IP address has been changed from 192.168.0.200 to something else; or (4) a VPN or proxy is intercepting your traffic. Run ipconfig /all on Windows or ip route on Linux/macOS to confirm your current gateway and subnet, then verify that 192.168.0.200 falls within your active network range.

Can I use 192.168.0.200 as my router's default gateway?

Technically yes — any address in the 192.168.0.1–192.168.0.254 range can serve as a gateway. However, most routers default to addresses like 192.168.0.1 at the low end of the subnet. Placing the gateway at 192.168.0.200 is unconventional and may cause confusion when troubleshooting. If you do configure your router to use 192.168.0.200 as its LAN IP, make sure your DHCP pool is adjusted accordingly so that client devices receive addresses in the same subnet.

How do I assign 192.168.0.200 as a static IP to a device?

You have two options. The first is to configure the device itself with a static IP: go into the device's network settings, disable DHCP (automatic IP), and manually enter 192.168.0.200 as the IP address, 255.255.255.0 as the subnet mask, and your router's address (e.g., 192.168.0.1) as the default gateway. The second — and often preferred — option is to set up a DHCP reservation in your router's admin panel: log in to your router, find the DHCP reservation or address binding section, enter the device's MAC address, and assign 192.168.0.200 to it. This way the device still uses DHCP but always receives the same address.