192.168.0.104 Admin Login

192.168.0.104 is a Class C private IPv4 address belonging to the 192.168.0.0/24 subnet — one of the most widely used private network ranges in homes and small offices worldwide. Unlike fixed default gateway addresses such as 192.168.0.1 or 192.168.1.254, the address 192.168.0.104 is not hardcoded as a default gateway by any single major router manufacturer. Instead, it functions as a general-purpose private IP address — most commonly assigned dynamically by a router's DHCP server to a connected device such as a laptop, smartphone, smart TV, printer, IP camera, or gaming console. It can also be manually configured as a static IP address for any device on a 192.168.0.x network. Because it sits well within the usable host range of the subnet (192.168.0.1 through 192.168.0.254), it is a perfectly valid and stable address for any networked device in your home or office.

How to Access 192.168.0.104

If your router or network device has been configured to use 192.168.0.104 as its management address, you can access its admin panel by opening any web browser and typing http://192.168.0.104 directly into the address bar, then pressing Enter. This will load the device's login page, where you'll be prompted to enter a username and password. The most commonly used default credentials on devices assigned to this address are:

• Username: admin | Password: admin
• Username: admin | Password: password
• Username: admin | Password: 1234
• Username: admin | Password: (blank)

Always check the label on the bottom or back of your device for the exact default credentials. If you have previously changed the password and forgotten it, you will need to perform a factory reset to restore the defaults. Keep in mind that because 192.168.0.104 is a private IP address, it is only reachable from within your local network — you cannot access it from the internet.

If You Can't Access 192.168.0.104

If typing http://192.168.0.104 into your browser returns an error, a timeout, or simply doesn't load, there are several likely causes to investigate:

• Wrong gateway address: Your router's actual default gateway may not be 192.168.0.104. Open the Command Prompt on Windows (Start > type cmd > press Enter) and run ipconfig /all. Look for the Default Gateway field — that is the correct address to use. On macOS, go to System Settings > Network > your connection > Details. On Linux, run ip route in the terminal.
• Not connected to the right network: Make sure your device is connected to the same Wi-Fi or Ethernet network as the device at 192.168.0.104. You cannot reach a private IP from a different network.
• IP address conflict: If two devices on your network share the address 192.168.0.104, neither may respond correctly. Check your router's DHCP client list to identify conflicts.
• Browser cache or extension issues: Try opening the address in a private/incognito window, or use a different browser entirely.
• Firewall blocking access: Temporarily disable your computer's firewall or security software and try again.

If none of these steps resolve the issue, consult our guide on how to find your router IP address to confirm the correct address for your specific setup.

192.168.0.104 as a DHCP-Assigned Address

In most home and small-office networks built on the 192.168.0.0/24 subnet, the router's DHCP server automatically assigns IP addresses to devices as they connect. The address 192.168.0.104 falls squarely within the typical DHCP pool range, which most routers set between 192.168.0.100 and 192.168.0.200 by default. This means your device — whether it's a Windows PC, MacBook, Android phone, iPhone, smart TV, or IoT gadget — may have been automatically assigned 192.168.0.104 by your router.

DHCP leases are temporary. Your device may hold 192.168.0.104 for a set period (commonly 24 hours to 7 days), after which the router may reassign it to a different device. If you need a device to always use 192.168.0.104, you should either:

• Set a static IP address directly on the device itself, or
• Configure a DHCP reservation (also called address binding) in your router's admin panel, which ties the address 192.168.0.104 permanently to that device's MAC address.

DHCP reservations are especially useful for printers, IP cameras, NAS drives, and smart home hubs that need a consistent address for reliable communication.

Setting 192.168.0.104 as a Static IP Address

Assigning 192.168.0.104 as a static (fixed) IP address to a device on your network ensures it always uses the same address, regardless of DHCP lease renewals or router reboots. Here's how to do it on the most common operating systems:

Windows 10 / 11

1. Right-click the Start button and select Network Connections.
2. Click Change adapter options, then right-click your active connection (Wi-Fi or Ethernet) and choose Properties.
3. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.
4. Choose Use the following IP address and enter:
   • IP address: 192.168.0.104
   • Subnet mask: 255.255.255.0
   • Default gateway: 192.168.0.1 (or your router's actual gateway)
5. Enter your preferred DNS servers (e.g., 8.8.8.8 and 8.8.4.4) and click OK.

macOS

1. Open System Settings > Network > select your connection > Details.
2. Go to the TCP/IP tab and change Configure IPv4 to Manually.
3. Enter 192.168.0.104 as the IP address, 255.255.255.0 as the subnet mask, and your router's IP as the router address.
4. Click OK and then Apply.

Important: Before assigning 192.168.0.104 as a static address, make sure no other device on your network is already using it. An IP address conflict will cause connectivity problems for both devices involved.

Changing Your Network Password via the Router Admin Panel

Whether 192.168.0.104 is your device's assigned address or your router's management IP, keeping your network secure starts with a strong admin password. To change your router's admin or Wi-Fi password, log in to your router's admin panel (typically at 192.168.0.1 or 192.168.1.254 depending on your router brand) and navigate to the Administration, System, or Wireless Security section. From there you can:

• Change the router admin password to prevent unauthorized access to your settings.
• Update your Wi-Fi password (WPA2/WPA3 key) to secure your wireless network.
• Rename your SSID (network name) to something that doesn't reveal your router brand or model.

Always use a password that is at least 12 characters long and combines uppercase letters, lowercase letters, numbers, and symbols. Avoid using default passwords — they are publicly documented and easy for attackers to guess.

Router Username and Password List

What Is 192.168.0.104? Understanding Private IP Addresses

192.168.0.104 is a private IPv4 address in the Class C range, defined by RFC 1918. The entire 192.168.0.0/24 block — spanning from 192.168.0.0 to 192.168.0.255 — is reserved exclusively for use within private networks. These addresses are never routed over the public internet, which means 192.168.0.104 is invisible to the outside world and can only be reached by devices on the same local network.

Here's how private addressing works in practice on a typical 192.168.0.x network:

• Your router holds the gateway address, usually 192.168.0.1.
• Your first connected device (e.g., a laptop) might receive 192.168.0.100.
• Your smartphone might receive 192.168.0.101.
• Your smart TV might receive 192.168.0.102.
• Your printer or IP camera might receive 192.168.0.103.
• Your next device could receive 192.168.0.104.

Each of these addresses is unique within your network and allows your router to correctly direct internet traffic to and from each device. The router itself has a separate public IP address assigned by your Internet Service Provider (ISP), which is the address the rest of the internet sees. All devices behind the router — including the one at 192.168.0.104 — share that single public IP through a process called Network Address Translation (NAT).

Because 192.168.0.104 is a private address, multiple households and businesses around the world can use it simultaneously without any conflict — each one exists in its own isolated local network.

192.168.0.104 and the 192.168.0.0/24 Subnet

The 192.168.0.0/24 subnet is one of the three private IPv4 ranges defined by RFC 1918 and is by far the most commonly deployed in consumer networking equipment. With a subnet mask of 255.255.255.0, this network supports up to 254 usable host addresses — from 192.168.0.1 to 192.168.0.254. The address 192.168.0.0 is the network address and 192.168.0.255 is the broadcast address; neither can be assigned to a device.

Within this subnet, several addresses are particularly well-known and frequently used:

• 192.168.0.1 — The most common default gateway address for routers from brands like TP-Link, D-Link, Tenda, and many others.
• 192.168.0.100–192.168.0.200 — The typical DHCP pool range, where addresses like 192.168.0.104 are dynamically assigned to client devices.
• 192.168.1.254 — A common alternative gateway used by some ISP-provided modems and routers.

Understanding where 192.168.0.104 sits within this subnet helps you plan your network more effectively — for example, by reserving lower addresses (192.168.0.2–192.168.0.99) for static assignments to servers, printers, and cameras, while leaving the higher range for DHCP clients.

Frequently Asked Questions About 192.168.0.104

Is 192.168.0.104 a valid IP address?

Yes, 192.168.0.104 is a fully valid private IPv4 address. It belongs to the 192.168.0.0/24 subnet and can be assigned to any device on a local network that uses this address range. It is not a public IP address and cannot be accessed from outside your local network.

What router brand uses 192.168.0.104 as its default gateway?

No major router manufacturer uses 192.168.0.104 as a hardcoded default gateway address. It is a general-purpose private IP that is most commonly assigned dynamically by a DHCP server to a client device (such as a PC, phone, or printer) on a 192.168.0.x network. The typical default gateway on such networks is 192.168.0.1. If you are looking for your router's admin panel, try accessing 192.168.0.1 instead.

How do I find out which device has the IP address 192.168.0.104?

Log in to your router's admin panel (usually at 192.168.0.1) and navigate to the DHCP Client List, Connected Devices, or LAN section. This will show you a table of all devices currently connected to your network along with their assigned IP addresses, MAC addresses, and sometimes device names. Look for the entry showing 192.168.0.104 to identify which device holds that address.

Can two devices share the IP address 192.168.0.104?

No. Within a single network, each device must have a unique IP address. If two devices are both assigned 192.168.0.104 — for example, if one device has it set as a static IP while the router's DHCP server assigns it to another — an IP address conflict will occur. Both devices will experience network disruptions. To resolve this, either change the static IP on one device or configure a DHCP reservation in your router to prevent the address from being assigned dynamically.

How do I release and renew the IP address 192.168.0.104 on Windows?

If your Windows computer has been assigned 192.168.0.104 and you want to release and renew it, open the Command Prompt as Administrator and run the following commands in order: ipconfig /release followed by ipconfig /renew. This will release the current DHCP lease (including 192.168.0.104) and request a new IP address from your router. Note that you may receive the same address again if it is still available in the DHCP pool.

What is the difference between 192.168.0.104 and 192.168.1.1?

192.168.1.1 is a default gateway address used by many router brands (such as Linksys, Netgear, and ASUS) as the router's own management IP. 192.168.0.104, on the other hand, is a client device address in the 192.168.0.x subnet — it is assigned to a device connected to the network, not to the router itself. They also belong to different subnets: 192.168.1.x and 192.168.0.x, which means devices on one subnet cannot directly communicate with devices on the other without routing.

Is it safe to use 192.168.0.104 as a static IP for my printer or camera?

Yes, assigning 192.168.0.104 as a static IP to a printer, IP camera, NAS drive, or other network device is a common and recommended practice. It ensures the device always has the same address, making it easier to connect to and manage. Just make sure to either exclude 192.168.0.104 from your router's DHCP pool or set up a DHCP reservation to prevent address conflicts with dynamically assigned devices.