192.168.0.10 Admin Login

192.168.0.10 is a Class C private IPv4 address used as the default gateway by a select group of networking devices, most notably D-Link print servers (such as the DP-300U, DP-311P, and DP-311U), the Luxul XAP-1610 Apex Wave 2 AC3100 Dual-Band Access Point, Intel Wireless Gateway II (AP1210), and the Comtrend PG-9182AC PowerGrid adapter. Unlike the more widely known gateway addresses such as 192.168.0.1 or 192.168.1.254, the address 192.168.0.10 is used by a narrower set of devices — primarily network-attached print servers and enterprise-grade wireless access points. It sits within the 192.168.0.0/24 subnet, which supports up to 254 usable host addresses. Because it is a private IP, it is not routable on the public internet and is exclusively used within local area networks (LANs). If your device uses 192.168.0.10 as its default gateway, you can access its admin panel by typing http://192.168.0.10 directly into your browser's address bar.

How to Access 192.168.0.10

To reach the admin panel of any device using 192.168.0.10 as its default IP, follow these steps:

1. Connect to the network — Make sure your computer or laptop is connected to the same local network as the device, either via an Ethernet cable or Wi-Fi.
2. Open your browser — Launch any modern web browser (Chrome, Firefox, Edge, or Safari).
3. Enter the address — Type http://192.168.0.10 into the address bar and press Enter. Do not use a search engine — type it directly into the address bar.
4. Enter your credentials — You will be presented with a login page. The most common default credentials for devices using this IP are:
   • Username: admin / Password: admin
   • Username: admin / Password: (leave blank)
   • Username: admin / Password: password
   • Username: admin / Password: 1234
   • Username: root / Password: 12345 (Comtrend PG-9182AC)
5. Navigate the dashboard — Once logged in, you can configure wireless settings, change passwords, assign static IPs, update firmware, and manage connected devices.

Keep in mind that 192.168.0.10 is a private IP address, meaning it is only accessible from within your local network. You cannot reach this admin panel from outside your home or office network without a VPN or special port-forwarding configuration.

If You Can't Access 192.168.0.10

If typing http://192.168.0.10 into your browser returns an error, a blank page, or redirects you to a search engine, there are several possible causes and fixes:

• Wrong default gateway — Your device may not actually use 192.168.0.10 as its gateway. To verify, open the Command Prompt on Windows (Start > type cmd > press Enter) and run ipconfig /all. Look for the Default Gateway field. On macOS or Linux, run netstat -nr or ip route in the Terminal. If the gateway shown is different, use that IP instead. You can also check our guide to find your router IP address.
• Not connected to the correct network — You must be on the same local network as the device. If you are connected to a different Wi-Fi network or using mobile data, you will not be able to reach 192.168.0.10.
• IP address has been changed — A previous administrator may have changed the default IP from 192.168.0.10 to something else. In this case, you will need to perform a factory reset to restore the original settings.
• Browser cache or HTTPS conflict — Some browsers auto-redirect to HTTPS. Make sure you are typing http:// (not https://) before the IP address. Also try clearing your browser cache or using a private/incognito window.
• Firewall or antivirus blocking — Temporarily disable your firewall or antivirus software and try again.
• Device is powered off or unresponsive — Restart the device and wait 60 seconds before trying again.

Router Brands & Devices That Use 192.168.0.10

Unlike more universal gateway addresses such as 192.168.0.1 or 10.0.0.1, the IP address 192.168.0.10 is associated with a specific set of devices. Here is a breakdown of the confirmed brands and models:

• D-Link — D-Link is one of the most prominent brands to use 192.168.0.10 as a default IP, specifically for its network print servers. Confirmed models include the DP-300U, DP-311P, DP-311U, and DP-300+. These devices allow you to share USB and parallel printers across a local network. The factory default IP address for all these models is 192.168.0.10 with a subnet mask of 255.255.255.0.
• Luxul — The XAP-1610 Apex Wave 2 AC3100 Dual-Band Wireless Access Point uses 192.168.0.10 as its default management IP. This is a professional-grade 802.11ac Wave 2 access point designed for commercial and residential AV/IT installations. It supports PoE (Power over Ethernet) and is compatible with the Luxul Wireless Controller for multi-AP deployments.
• Intel — Intel's Wireless Gateway II (AP1210) uses 192.168.0.10 as one of its default IP addresses. This device was part of Intel's early enterprise wireless networking lineup and is used in managed wireless environments.
• Comtrend — The PG-9182AC PowerGrid adapter uses 192.168.0.10 as its static default IP address (subnet mask 255.255.255.0). Comtrend is a provider of broadband access equipment, and this model is a powerline networking adapter with AC Wi-Fi capabilities.
• StarTech — The PM1115UWGB print server model also uses 192.168.0.10 as its default IP address, with default credentials of admin / (none).
• Z-Com — The XG-580 wireless device uses 192.168.0.10 as its default gateway IP address.

Changing Your Password on a 192.168.0.10 Device

Keeping the default password on any device accessible at 192.168.0.10 is a serious security risk. Whether you are using a D-Link print server, a Luxul access point, or a Comtrend adapter, you should change the default admin password as soon as possible. Here is how to do it:

1. Log in to the admin panel at http://192.168.0.10 using your current credentials.
2. Navigate to the Administration, Management, or System section — the exact label depends on your device's firmware.
3. Look for a Change Password or Admin Password option.
4. Enter your current password, then type your new password twice to confirm.
5. Click Save or Apply to store the changes.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Avoid using easily guessable passwords like admin, password, or 1234 — these are the first combinations any attacker will try. After changing your password, store it in a secure password manager so you do not lose access to your device.

How to Factory Reset a Device Using 192.168.0.10

If you have forgotten your login credentials or can no longer access the admin panel at 192.168.0.10, a factory reset will restore the device to its original settings, including the default IP address and default password. Note that a factory reset will erase all custom configurations, including Wi-Fi names, passwords, and port forwarding rules.

D-Link Print Servers (DP-300U, DP-311P, DP-311U)

1. Locate the Reset button on the back or bottom of the device.
2. With the device powered on, use a paperclip or pin to press and hold the Reset button for 10 seconds.
3. Release the button and wait for the device to reboot.
4. Once restarted, the IP address will return to 192.168.0.10 and the default credentials will be restored.

Luxul XAP-1610 Access Point

1. Locate the Reset button on the device (typically a small pinhole on the back or bottom panel).
2. With the device powered on, press and hold the Reset button for 10 seconds until the LEDs begin to blink, indicating a reset is in progress.
3. Release the button and allow the device to fully reboot (approximately 60–90 seconds).
4. After the reboot, the default IP 192.168.0.10 and default credentials (admin / admin) will be restored.

Comtrend PG-9182AC

1. Locate the Reset pinhole button on the device.
2. Press and hold it for 10–15 seconds with the device powered on.
3. Wait for the device to reboot and restore factory defaults, including the static IP 192.168.0.10 and subnet mask 255.255.255.0.

Router Username and Password List

What Is 192.168.0.10 as a Private IP Address?

192.168.0.10 is a Class C private IPv4 address that falls within the reserved private IP range of 192.168.0.0 – 192.168.255.255, as defined by RFC 1918. This means it is not routable on the public internet and can only be used within private local area networks (LANs). Every home router, office network, or enterprise system that uses the 192.168.0.x subnet can assign 192.168.0.10 to a device — whether that is a router, access point, print server, or any other networked hardware.

In the context of the 192.168.0.0/24 subnet, the address 192.168.0.10 is the 10th usable host address. The subnet supports 254 usable addresses (192.168.0.1 through 192.168.0.254), with 192.168.0.0 reserved as the network address and 192.168.0.255 reserved as the broadcast address. When a device like the D-Link DP-300U or Luxul XAP-1610 is assigned 192.168.0.10 as its default IP, it means that is the address you use to reach its web-based management interface from any other device on the same subnet.

It is important to understand that only one device on a network should use 192.168.0.10 at any given time. If two devices are assigned the same IP address, an IP address conflict will occur, causing both devices to become unreachable or behave erratically. If you suspect a conflict, check your router's DHCP client list or use a network scanner to identify all devices and their assigned IPs.

Other commonly used addresses in the same 192.168.0.x subnet include 192.168.0.1 (the most popular default gateway for many routers) and 192.168.0.1.1. If your device uses a different subnet entirely, you may want to explore 192.168.1.254, 192.168.2.1, 192.168.8.1, or 10.0.0.1 as alternative default gateways.

Frequently Asked Questions About 192.168.0.10

What is 192.168.0.10 used for?

192.168.0.10 is used as the default management IP address for specific networking devices, including D-Link print servers (DP-300U, DP-311P, DP-311U), the Luxul XAP-1610 wireless access point, the Intel Wireless Gateway II (AP1210), and the Comtrend PG-9182AC powerline adapter. You type 192.168.0.10 into your browser to access the admin panel of these devices.

Is 192.168.0.10 a valid IP address?

Yes, 192.168.0.10 is a fully valid Class C private IPv4 address. It belongs to the 192.168.0.0/24 subnet and can be assigned to any device on a local network. It is not a public IP and cannot be accessed from the internet.

What is the default username and password for 192.168.0.10?

The most common default credentials for devices using 192.168.0.10 are admin / admin. However, this varies by device: D-Link print servers often use admin with a blank password, the Comtrend PG-9182AC uses root / 12345, and the Luxul XAP-1610 uses admin / admin. Always check the label on your device or its manual for the exact defaults.

Why can't I access 192.168.0.10?

If you cannot reach 192.168.0.10, the most likely reasons are: you are not connected to the correct local network, the device's IP has been changed from the default, the device is powered off, or your browser is trying to use HTTPS instead of HTTP. Make sure to type http://192.168.0.10 (with http://) and that you are connected to the same network as the device.

How do I reset a device back to 192.168.0.10?

To restore 192.168.0.10 as the default IP, perform a factory reset on your device. For D-Link print servers and the Luxul XAP-1610, press and hold the Reset button for 10 seconds while the device is powered on. For the Comtrend PG-9182AC, hold the reset pinhole for 10–15 seconds. After the reboot, the device will return to 192.168.0.10 with factory-default credentials.

Can I change the IP address from 192.168.0.10 to something else?

Yes. Once you are logged into the admin panel at 192.168.0.10, you can navigate to the network or LAN settings section and assign a new static IP address to the device. This is useful if 192.168.0.10 conflicts with another device on your network. Just make sure the new IP is within the same subnet (e.g., 192.168.0.x) and is not already in use.

What other IP addresses are related to 192.168.0.10?

192.168.0.10 belongs to the 192.168.0.0/24 subnet. Other commonly used addresses in this range include 192.168.0.1 (the most popular default gateway), as well as 192.168.0.1.1. Devices on the same network are typically assigned sequential addresses such as 192.168.0.2, 192.168.0.3, and so on. Related gateway addresses from other subnets include 192.168.1.254, 192.168.2.1, 192.168.100.1, and 10.0.0.1.