10.0.0.2 Admin Login

Several router manufacturers — including Zoom, Gemtek, BEC Technologies, Jaht, and Belkin — use 10.0.0.2 as their default gateway IP address. It belongs to the Class A private IPv4 address space defined by RFC 1918, making it one of the less common but fully valid default gateway choices in home and small-office networking. Unlike the far more widespread 192.168.1.1 or 10.0.0.1, the address 10.0.0.2 is typically seen on ADSL modem-routers and specialised broadband gateway devices. Because it sits inside the large 10.0.0.0/8 private block, only one device on your local network should ever be assigned 10.0.0.2 at any given time — assigning it to more than one device will cause an IP address conflict that disrupts connectivity for every device on the network.

How to Access 10.0.0.2

To reach your router's administration panel, open any web browser — Chrome, Firefox, Edge, or Safari all work — and type http://10.0.0.2 directly into the address bar, then press Enter. Do not type it into a search engine; paste it into the address bar at the very top of the browser window. Within a few seconds you should see a login prompt asking for a username and password.

For most routers that ship with 10.0.0.2 as their default gateway, the factory credentials are:

• Username: admin  |  Password: admin
• Username: admin  |  Password: zoomadsl (Zoom ADSL series)
• Username: admin  |  Password: password (some Belkin models)
• Username: admin  |  Password: (blank) (some Gemtek and BEC models)

Always check the label on the underside or rear panel of your specific device, as manufacturers sometimes print the exact credentials there. Once you are logged in, you can manage wireless settings, security options, port forwarding, DHCP reservations, firmware updates, and much more.

Router Brands That Use 10.0.0.2 as Their Default Gateway

Not every router manufacturer chooses 10.0.0.2 — it is a relatively specialised default compared to the ubiquitous 192.168.x.x range. Below are the brands confirmed to ship devices with 10.0.0.2 as the out-of-the-box gateway address:

• Zoom — The Zoom ADSL WLAN X6 Modem/Router (Series 1046 / model 5590) and the X6 ADSL Router (Series 1058 / model 5590C) both default to 10.0.0.2. Zoom's ADSL line was widely sold through ISPs in North America and Europe.
• Gemtek — Gemtek produces OEM and white-label broadband gateway hardware for ISPs worldwide. Several Gemtek-branded and Gemtek-manufactured devices use 10.0.0.2 as the LAN gateway, with admin / admin as the default login pair.
• BEC Technologies — BEC (Billion Electric Company) routers such as the BEC 7402GTM, BEC 7402T, BEC 7800TN, BEC 8800N, and BEC 8920NE are documented to use 10.0.0.2. BEC devices are popular in Asia-Pacific ISP deployments.
• Jaht — Jaht networking equipment, distributed primarily in European markets, uses 10.0.0.2 as its default LAN IP on several ADSL router models.
• Belkin — Certain older Belkin Wireless-G and ADSL modem-router models (including some F5D-series devices) shipped with 10.0.0.2 as the default gateway, particularly units sold bundled with ISP packages.

If your device is not listed above but 10.0.0.2 appears as your gateway when you run ipconfig (Windows) or ip route (Linux/macOS), your ISP or a previous user may have manually configured the address. The login procedure is identical regardless of brand — navigate to http://10.0.0.2 and enter your credentials.

If You Can't Access 10.0.0.2

If typing http://10.0.0.2 into your browser produces an error or a blank page, work through the following checks before assuming the address is wrong:

1. Confirm your gateway address. On Windows, open Command Prompt (Start > cmd) and run ipconfig /all. Look for the line labelled Default Gateway. On macOS or Linux, run ip route show or netstat -nr and look for the default route. If the gateway shown is not 10.0.0.2, use whatever address is listed instead — or visit our guide to find your router IP address.
2. Check your physical connection. For the most reliable access, connect your computer to the router using an Ethernet cable rather than Wi-Fi. A wired connection eliminates wireless association issues that can prevent the admin page from loading.
3. Try HTTPS. Some newer firmware versions redirect plain HTTP to HTTPS. Try https://10.0.0.2 and accept any browser security warning about the self-signed certificate.
4. Disable VPN or proxy software. Active VPN clients or proxy settings can route your browser traffic away from the local network, making 10.0.0.2 unreachable. Temporarily disable them and try again.
5. Clear your browser cache. Cached redirects can send your browser to the wrong destination. Clear the cache or try an incognito/private window.
6. The IP may have been changed. If a previous administrator changed the router's LAN IP from 10.0.0.2 to something else, you will need to either find the new address via ipconfig or perform a factory reset to restore 10.0.0.2 as the default.

Factory Reset Procedures for 10.0.0.2 Routers

If you have forgotten your admin password or the router is behaving unexpectedly, a factory reset will restore 10.0.0.2 as the default gateway and wipe all custom settings. The exact procedure varies slightly by brand:

Zoom ADSL Routers (Series 1046 / 1058)

1. Make sure the router is powered on and the power LED is stable.
2. Locate the small Reset pinhole button on the rear panel.
3. Insert a straightened paperclip or SIM-eject tool and press and hold for 10–15 seconds until the LEDs flash or the device reboots.
4. Release the button and wait approximately 60 seconds for the router to complete its restart cycle.
5. Navigate to http://10.0.0.2 and log in with admin / zoomadsl.

BEC Technologies Routers (7402, 7800, 8800, 8920 series)

1. Ensure the device is powered on.
2. Press and hold the Reset button on the rear panel for 6 seconds or more until the device restarts.
3. Wait for the device to fully reboot (approximately 60–90 seconds).
4. Open your browser and go to http://10.0.0.2. Default credentials are typically admin / admin.

Gemtek & Jaht Routers

1. With the router powered on, locate the Reset pinhole on the back or bottom of the unit.
2. Hold the reset button for 10 seconds using a pin or paperclip.
3. Release and allow the router to reboot fully.
4. Access the admin panel at http://10.0.0.2 using admin / admin or a blank password.

Belkin F5D-Series Routers

1. Power on the router and wait for it to fully boot.
2. Press and hold the Reset button (usually recessed on the rear panel) for 10 seconds.
3. The router will reboot automatically. Wait for all LEDs to stabilise.
4. Navigate to http://10.0.0.2. Many Belkin models do not require a username; leave the username field blank and enter password or leave the password blank as well.

Important: A factory reset erases your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and any custom DNS settings. Make sure you have your ISP connection details (PPPoE username and password, or DHCP settings) to hand before resetting, so you can reconfigure your internet connection afterwards.

Changing Your Router Password at 10.0.0.2

Leaving your router on its factory-default password is one of the most common home network security mistakes. Anyone connected to your Wi-Fi — or anyone who gains brief physical access — can log into http://10.0.0.2 with the default credentials and change your settings, redirect your DNS, or monitor your traffic. Follow these steps to set a strong admin password:

1. Log into the admin panel at http://10.0.0.2 using your current credentials.
2. Navigate to the Administration, Management, or System section — the exact label depends on your router's firmware.
3. Look for a Change Password or Admin Password field.
4. Enter your current password, then type your new password twice to confirm.
5. Click Save or Apply. The router may prompt you to log in again with the new password immediately.

A strong router password should be at least 12 characters long and include a mix of uppercase letters, lowercase letters, numbers, and symbols. Avoid using the same password you use for your Wi-Fi network or any online accounts. Store it somewhere safe — if you forget it, your only recovery option is a full factory reset.

Router Username and Password List

What Kind of IP Address Is 10.0.0.2?

10.0.0.2 is a Class A private IPv4 address. The entire 10.0.0.0/8 block — covering 10.0.0.0 through 10.255.255.255 — is reserved for private use by RFC 1918 and is never routed on the public internet. Class A private addresses are the largest of the three private ranges, offering over 16 million usable host addresses within a single network. This makes the 10.x.x.x range especially popular in large enterprise environments, data centres, and ISP infrastructure, though individual consumer routers like those from Zoom and BEC Technologies also make use of it.

When your router uses 10.0.0.2 as its gateway, the devices that connect to it receive addresses from the same subnet — typically 10.0.0.3, 10.0.0.4, 10.0.0.5, and so on, assigned automatically by the router's built-in DHCP server. Here is an example of how address assignment might look on a typical home network using this gateway:

• Router (gateway): 10.0.0.2
• Desktop PC: 10.0.0.3
• Laptop: 10.0.0.4
• Smartphone: 10.0.0.5
• Smart TV: 10.0.0.6

Every device on the network uses 10.0.0.2 as its gateway to reach the internet. When your laptop wants to load a webpage, it sends the request to 10.0.0.2, which forwards it to your ISP and returns the response. The private address 10.0.0.2 itself is never visible to the outside world — your ISP assigns a separate public IP address to the router's WAN interface for that purpose.

Because 10.0.0.2 is a private address, it is completely safe to access from within your local network. No one on the internet can reach it directly. However, you should still protect the admin panel with a strong password, since anyone on your local Wi-Fi network can attempt to log in.

Related IP Addresses in the 10.0.0.x Subnet

If 10.0.0.2 is not your router's gateway, or if you are managing a network that uses the broader 10.0.0.0/8 private range, the following addresses are also commonly encountered as default gateways or management interfaces:

• 10.0.0.1 — The most widely used gateway in the 10.0.0.x subnet. Many Cisco, Xfinity (Comcast), and Apple AirPort devices default to this address. If 10.0.0.2 does not work for your router, try 10.0.0.1 first.
• 10.0.0.138 — Occasionally seen as a router management address in certain ISP-provisioned setups where 10.0.0.1 and 10.0.0.2 are assigned to other devices.
• 192.168.1.1 — The single most common default gateway globally, used by Linksys, TP-Link, Netgear, and many others.
• 192.168.0.1 — Another extremely common default, used by Netgear, D-Link, and various ISP-supplied routers.
• 192.168.1.254 — Used by some DSL routers and ISP gateways, particularly in France (Orange/Livebox) and some Billion/BEC models.
• 192.168.100.1 — Common on cable modems and some ISP-supplied gateways.
• 192.168.8.1 — Default gateway for Huawei routers and mobile Wi-Fi hotspot devices.

If you are unsure which address your router uses, the fastest way to find out is to run ipconfig /all on Windows or ip route on Linux/macOS and look at the Default Gateway field.

Frequently Asked Questions About 10.0.0.2

Is 10.0.0.2 the same as 192.168.1.1?

No. Both are private IPv4 addresses used as router gateways, but they belong to different private ranges. 10.0.0.2 is a Class A address from the 10.0.0.0/8 block, while 192.168.1.1 is a Class C address from the 192.168.0.0/16 block. They serve the same purpose — acting as the local gateway — but are used by different router brands. Zoom, Gemtek, BEC Technologies, Jaht, and certain Belkin models use 10.0.0.2, whereas brands like Linksys and TP-Link typically use 192.168.1.1.

Why does my router use 10.0.0.2 instead of 10.0.0.1?

Some manufacturers, particularly those producing ADSL modem-routers for ISP deployment, reserve 10.0.0.1 for the ISP's own network equipment (such as a DSLAM or upstream aggregation device) and assign 10.0.0.2 to the customer-premises router. This is a deliberate design choice to avoid conflicts in point-to-point WAN configurations. Zoom's ADSL series is a well-known example of this approach.

Can two devices on my network both use 10.0.0.2?

No. Assigning 10.0.0.2 to more than one device on the same network causes an IP address conflict. Both devices will experience intermittent or total loss of connectivity, and other devices on the network may also be affected. Your router's DHCP server is designed to prevent this by assigning unique addresses to each client, but conflicts can still occur if you manually assign static IPs without checking for duplicates.

How do I know if 10.0.0.2 is my router's IP address?

On Windows, open Command Prompt and type ipconfig /all, then press Enter. Find the network adapter you are using (Wi-Fi or Ethernet) and look at the Default Gateway line. If it shows 10.0.0.2, that is your router's admin address. On macOS, go to System Settings > Network > your connection > Details and check the Router field. On Android or iOS, tap your connected Wi-Fi network and look for the Gateway or Router field in the advanced details.

Is it safe to access 10.0.0.2?

Yes — 10.0.0.2 is a private IP address that is only reachable from within your local network. No one on the internet can access it directly. However, you should always protect your router's admin panel with a strong, unique password. If your router is still using the factory default credentials (such as admin / admin or admin / zoomadsl), anyone connected to your Wi-Fi can log in and change your settings. Change the admin password as soon as you set up your router.

What should I do if I forgot my 10.0.0.2 admin password?

If you cannot remember the password you set for your router's admin panel at 10.0.0.2, your only option is to perform a factory reset. Locate the Reset pinhole button on the back or bottom of your router (Zoom, BEC, Gemtek, Jaht, or Belkin device), press and hold it for 10–15 seconds with a paperclip, and wait for the router to reboot. After the reset, you can log in at http://10.0.0.2 using the factory default credentials printed on the device label. Remember to set a new strong password immediately after logging in.

Can I change my router's IP address from 10.0.0.2 to something else?

Yes. Once you are logged into the admin panel at 10.0.0.2, navigate to the LAN or Network settings section and look for the LAN IP Address field. You can change it to any valid private IP address, such as 192.168.1.1 or 10.0.0.1. After saving, your router will reboot and you will need to use the new address to access the admin panel going forward. Only change the LAN IP if you have a specific reason to do so — for example, to avoid a conflict with another device or to match a corporate network policy.