192.168.99.1 Admin Login

192.168.99.1 is a private IPv4 address used as the default gateway by a select group of router manufacturers, most notably Lenovo (on its Newifi 3 and Newifi 3D2 models) and Enable Networks (on its CR3000 model). While less common than addresses like 192.168.1.1 or 192.168.0.1, 192.168.99.1 is a fully valid Class C private IP address that operates within the 192.168.99.0/24 subnet. It is also frequently assigned manually by network administrators who want to avoid the most commonly targeted default subnets, making it a smart choice for slightly more security-conscious home and small office setups. Because it sits in the less-crowded 192.168.99.x range, it is far less likely to conflict with neighboring networks or VPN tunnels that default to the 192.168.1.x or 192.168.0.x ranges.

How to Access 192.168.99.1

To reach your router's admin panel at 192.168.99.1, make sure your device is connected to the router — either via an Ethernet cable or over Wi-Fi — and then open any web browser. Type http://192.168.99.1 directly into the address bar and press Enter. Do not use a search engine to navigate there; type the address directly into the URL bar to avoid being redirected to a search results page instead of your router's login screen.

Once the login page loads, you will be prompted to enter a username and password. For Lenovo Newifi 3 and Newifi 3D2 routers, the default credentials are typically admin / admin. For Enable Networks CR3000 devices, check the label on the bottom or back of the unit for the printed default credentials. After logging in, you will have full access to your router's configuration dashboard, where you can manage Wi-Fi settings, set up port forwarding, configure DHCP reservations, update firmware, and more.

If the page does not load, double-check that 192.168.99.1 is actually your router's gateway address. On Windows, open Command Prompt and type ipconfig, then look for the Default Gateway field. On macOS, go to System Preferences > Network, select your active connection, and click Advanced > TCP/IP to see the router address. If the gateway shown is different from 192.168.99.1, visit our guide to find your router IP address.

Router Brands That Use 192.168.99.1

Unlike the most popular default gateways, 192.168.99.1 is associated with a smaller, specific set of manufacturers. Here are the confirmed brands and models that use this address out of the box:

• Lenovo Newifi 3 — Lenovo's Newifi series was a line of consumer and enthusiast-grade routers sold primarily in the Chinese market. The Newifi 3 uses 192.168.99.1 as its default LAN gateway. Its admin panel is accessible at http://192.168.99.1 with the default login admin / admin.
• Lenovo Newifi 3D2 — The 3D2 is an upgraded variant of the Newifi 3, also shipping with 192.168.99.1 as the default gateway. It features a similar web-based admin interface and uses the same default credentials. The factory reset procedure for this model is described in detail below.
• Enable Networks CR3000 — The CR3000 is a commercial-grade router from Enable Networks that ships with 192.168.99.1 as its default gateway. It is designed for small business and enterprise edge deployments. Always verify the exact credentials on the device label, as Enable Networks units may ship with customized defaults depending on the deployment region.

If your router is not one of the models listed above but you are seeing 192.168.99.1 as your gateway, it is likely that a previous administrator manually changed the router's LAN IP to this address, or your ISP has pre-configured the device with a non-standard default. In either case, you can still access the admin panel at http://192.168.99.1 as long as your device is connected to that network.

Default Username and Password for 192.168.99.1

Before you can make any changes through the 192.168.99.1 admin panel, you need to log in with the correct credentials. The table below lists the most common default username and password combinations associated with routers that use 192.168.99.1:

• Username: admin | Password: admin
• Username: admin | Password: (leave blank)
• Username: admin | Password: password
• Username: admin | Password: 1234

For Lenovo Newifi 3 and 3D2 routers, admin / admin is the confirmed factory default. For Enable Networks CR3000 devices, check the sticker on the bottom or rear panel of the unit, as credentials may vary by firmware version or regional configuration. If none of the combinations above work, it is possible that the password was changed by a previous user. In that case, you will need to perform a factory reset to restore the default credentials — see the section below for step-by-step instructions.

Router Username and Password List

How to Change Your Wi-Fi Password via 192.168.99.1

Keeping your wireless network secure starts with a strong, unique Wi-Fi password. To change it through the 192.168.99.1 admin panel, follow these steps:

1. Open your browser and navigate to http://192.168.99.1.
2. Log in with your admin credentials (default: admin / admin for Lenovo Newifi models).
3. Look for a section labeled Wireless, Wi-Fi Settings, or WLAN in the navigation menu.
4. Find the Security or Password field and enter your new password. Use a mix of uppercase and lowercase letters, numbers, and symbols for maximum security.
5. Click Save or Apply to confirm the change.
6. Reconnect all your devices using the new password.

It is also strongly recommended that you change the router admin password itself — not just the Wi-Fi password. To do this, look for an Administration, System, or Account section within the 192.168.99.1 dashboard and update the login credentials there. Using the default admin / admin combination leaves your router vulnerable to unauthorized access from anyone connected to your network.

Factory Reset for Routers Using 192.168.99.1

If you have forgotten your admin password or your router is behaving unexpectedly, performing a factory reset will restore all settings — including the default gateway of 192.168.99.1 and the default login credentials — to their original values. Note that a factory reset will erase all custom configurations, including your Wi-Fi name, password, port forwarding rules, and any other changes you have made.

Lenovo Newifi 3D2 — Factory Reset Steps

1. Unplug the power cord from the Lenovo Newifi 3D2 router.
2. Locate the Reset button on the back or bottom of the device (you may need a paperclip or pin to press it).
3. Press and hold the Reset button while simultaneously plugging the power cord back in.
4. Continue holding the Reset button for approximately 10 seconds until the indicator LEDs flash or change behavior, signaling that the reset is in progress.
5. Release the button and wait for the router to fully reboot — this typically takes 60–90 seconds.
6. Once rebooted, the router will be restored to factory defaults. You can now access the admin panel at http://192.168.99.1 using admin / admin.

Lenovo Newifi 3 — Factory Reset Steps

1. With the router powered on, locate the small Reset button on the back of the unit.
2. Use a pin or straightened paperclip to press and hold the Reset button for approximately 10 seconds.
3. Release the button when the LEDs begin to flash rapidly, indicating the reset has been triggered.
4. Wait for the router to reboot completely before attempting to reconnect.
5. After the reboot, navigate to http://192.168.99.1 and log in with the default credentials.

Enable Networks CR3000 — Factory Reset Steps

1. Ensure the CR3000 is powered on.
2. Locate the Reset pinhole button on the rear panel of the device.
3. Insert a pin or paperclip and press and hold for 10–15 seconds until the status LEDs indicate a reset cycle.
4. Release the button and allow the device to reboot fully.
5. Once restored, access the admin interface at http://192.168.99.1 and refer to the device label for the default login credentials.

What Is 192.168.99.1? Understanding This Private IP Address

192.168.99.1 is a private IPv4 address that belongs to the Class C private address range defined by RFC 1918. This range spans from 192.168.0.0 to 192.168.255.255, and addresses within it are reserved exclusively for use on local area networks (LANs). They are never routed over the public internet, which means 192.168.99.1 is completely invisible to the outside world — it only exists and functions within your private home or office network.

When a router uses 192.168.99.1 as its default gateway, it becomes the central hub of the 192.168.99.0/24 subnet. This means the router can assign private IP addresses to connected devices in the range of 192.168.99.2 through 192.168.99.254 via DHCP. For example:

• Your laptop might receive 192.168.99.2
• Your smartphone might receive 192.168.99.3
• Your smart TV might receive 192.168.99.4
• Your printer might receive 192.168.99.5

Each of these devices uses 192.168.99.1 as their gateway to communicate with the internet. When you request a webpage, your device sends the request to 192.168.99.1, which then forwards it to your ISP and returns the response back to your device using Network Address Translation (NAT).

One practical advantage of the 192.168.99.x subnet is that it is far less commonly used than 192.168.1.x or 192.168.0.x. This makes it a popular choice for network administrators who want to reduce the risk of IP address conflicts when connecting to VPNs or bridging multiple networks together. Many VPN clients default to the 192.168.1.x range, so using 192.168.99.1 as your gateway can prevent routing conflicts that would otherwise disrupt your VPN connection.

Troubleshooting: Can't Access 192.168.99.1?

If typing http://192.168.99.1 into your browser doesn't bring up a login page, work through the following troubleshooting steps before assuming there is a serious problem:

• Confirm your gateway address: Open Command Prompt on Windows and type ipconfig, or open Terminal on macOS and type ipconfig getifaddr en0. Look for the Default Gateway field. If it shows a different address (such as 192.168.1.1 or 192.168.0.1), then 192.168.99.1 is not your router's current IP.
• Check your connection: Make sure your device is connected to the router's network — either via Ethernet cable or Wi-Fi. You cannot reach 192.168.99.1 from a different network or over mobile data.
• Disable VPN or proxy: Active VPN connections or proxy settings can redirect or block access to local gateway addresses. Temporarily disable any VPN before trying again.
• Use the correct URL format: Type http://192.168.99.1 — not https:// — as most router admin panels do not use SSL by default. Also avoid typing it into a search bar.
• Try a different browser or clear cache: Sometimes cached data or browser extensions interfere with local network pages. Try an incognito/private window or a different browser entirely.
• Restart the router: Power cycle your router by unplugging it for 30 seconds and plugging it back in. Wait for it to fully boot before trying again.
• Perform a factory reset: If all else fails and you suspect the gateway IP has been changed, a factory reset will restore 192.168.99.1 as the default gateway on Lenovo Newifi and Enable Networks CR3000 devices.

Related IP Addresses in the 192.168.99.x Subnet

The 192.168.99.0/24 subnet contains 254 usable host addresses, ranging from 192.168.99.1 to 192.168.99.254. While 192.168.99.1 is the most commonly used address in this range as a default gateway, other addresses in the subnet serve important roles in a properly configured network. Here are some related IPs you may encounter:

• 192.168.99.2 – 192.168.99.254: These are the addresses your router's DHCP server assigns to connected client devices such as computers, phones, tablets, smart TVs, and IoT devices.
• 192.168.99.100 – 192.168.99.200: A common DHCP pool range configured on routers using this subnet, leaving lower and higher addresses free for static assignment.
• 192.168.99.255: The broadcast address for the 192.168.99.0/24 subnet — used to send data to all devices on the network simultaneously. This address cannot be assigned to any individual device.
• 192.168.99.0: The network address for this subnet — it identifies the subnet itself and is not assignable to any host.

If you are managing a network with multiple VLANs or subnets, you may also want to explore other common private gateway addresses such as 192.168.1.254, 192.168.100.1, 192.168.8.1, or 10.0.0.1 for segmenting different parts of your network.

Frequently Asked Questions About 192.168.99.1

What is 192.168.99.1?

192.168.99.1 is a private IPv4 Class C address used as the default gateway on specific router models, including the Lenovo Newifi 3, Lenovo Newifi 3D2, and the Enable Networks CR3000. You can use it to access your router's admin panel by typing http://192.168.99.1 into your browser while connected to the network.

Which routers use 192.168.99.1 as their default gateway?

The confirmed routers that ship with 192.168.99.1 as their factory default gateway are the Lenovo Newifi 3, Lenovo Newifi 3D2, and the Enable Networks CR3000. Other routers may also use this address if it has been manually configured by a network administrator.

What is the default username and password for 192.168.99.1?

For Lenovo Newifi 3 and 3D2 routers, the default login is admin for both the username and password. For the Enable Networks CR3000, check the label on the back or bottom of the device. If the defaults have been changed and you no longer know the credentials, you will need to perform a factory reset to regain access via 192.168.99.1.

Is 192.168.99.1 safe to use?

Yes, 192.168.99.1 is a private IP address and is never exposed to the public internet. It is only accessible from within your local network. However, you should always change the default admin password on your router to prevent unauthorized access from other devices on the same network.

Why can't I access 192.168.99.1?

The most common reasons you cannot reach 192.168.99.1 are: your device is not connected to the correct network, your router uses a different gateway address (check with ipconfig on Windows), you have an active VPN that is overriding local routing, or the router's LAN IP has been changed from the default. Try the troubleshooting steps listed above, or perform a factory reset on your Lenovo Newifi or Enable Networks device to restore 192.168.99.1 as the default gateway.

Can I change 192.168.99.1 to a different IP address?

Yes. Once logged into the admin panel at http://192.168.99.1, navigate to LAN Settings or Network Settings and update the router's IP address to your preferred value, such as 192.168.1.1 or 192.168.10.1. After saving, you will need to use the new address to access the admin panel going forward.

What is the subnet for 192.168.99.1?

192.168.99.1 belongs to the 192.168.99.0/24 subnet, with a subnet mask of 255.255.255.0. This subnet supports up to 254 usable host addresses, ranging from 192.168.99.1 (the gateway) to 192.168.99.254, with 192.168.99.255 reserved as the broadcast address.