192.168.60.1 Admin Login

192.168.60.1 is a private IPv4 address that belongs to the Class C range and is most commonly encountered as a gateway address in VLAN-segmented networks. Unlike more widely recognized defaults such as 192.168.1.1 or 192.168.0.1, this address is not the factory default of a single mainstream consumer router brand. Instead, you are most likely to find 192.168.60.1 in use on MikroTik routers configured for multi-VLAN environments, Cisco enterprise and SMB networking equipment, and Ubiquiti UniFi systems where the 192.168.60.0/24 subnet has been assigned to a dedicated network segment such as an IoT VLAN, guest network, or VPN tunnel. Network administrators frequently choose the 192.168.60.x range precisely because it avoids conflicts with the far more common 192.168.1.x and 192.168.0.x subnets used by most consumer routers. If you are seeing 192.168.60.1 as your gateway, you are likely on a professionally configured or custom-built network.

How to Access 192.168.60.1

To reach the admin panel at 192.168.60.1, open any web browser on a device that is connected to the same network and type http://192.168.60.1 directly into the address bar — not the search bar. Press Enter and you should be presented with a login page. From there, enter your router or gateway's username and password. If you have never changed these credentials, check the sticker on the back or bottom of your device for the factory defaults. Common default combinations include admin / admin, admin / password, and admin / 1234, though this varies by manufacturer and model.

Because 192.168.60.1 is a private IP address, it is only reachable from within the local network — you cannot access it from the internet. If you are using a MikroTik router with this address assigned to a specific VLAN interface, make sure your device is connected to that VLAN (either via a tagged port or the correct wireless SSID) before attempting to access the admin panel. On Cisco equipment, you may need to connect to the specific interface or management VLAN that has 192.168.60.1 assigned. For Ubiquiti UniFi deployments, the UniFi Network Application dashboard is typically your primary management interface, but 192.168.60.1 may serve as the gateway for a specific virtual network you have created.

If You Can't Access 192.168.60.1

If entering http://192.168.60.1 in your browser returns an error or a blank page, there are several things you should check. First, confirm that your device is actually connected to the network that uses the 192.168.60.x subnet. On Windows, open Command Prompt (Start > type cmd > press Enter) and run ipconfig. Look for the Default Gateway field — if it does not show 192.168.60.1, your device is connected to a different network segment and will not be able to reach this address. On macOS, go to System Settings > Network > your active connection > Details, and check the Router field. On Linux, run ip route in the terminal and look for the default route.

If you are on a MikroTik setup with multiple VLANs, ensure your device is on the correct VLAN — for example, if 192.168.60.1 is the gateway for your IoT VLAN, a device on your main LAN (e.g., 192.168.1.x) will not be able to reach it unless inter-VLAN routing is explicitly configured. On Ubiquiti UniFi systems, check that the virtual network using the 192.168.60.0/24 subnet is active and that your device is assigned to it. If you still cannot connect, try disabling any VPN software on your device, as VPN clients can reroute traffic and prevent access to local gateway addresses. You can also check our guide to find your router IP address for more detailed steps.

Router Brands That Use 192.168.60.1

As noted above, 192.168.60.1 is not the out-of-the-box default for most consumer routers. However, it is actively used by the following platforms and brands in specific configurations:

• MikroTik — MikroTik routers are among the most common devices you will find using 192.168.60.1. Because MikroTik's RouterOS gives administrators full control over IP addressing, network engineers frequently assign 192.168.60.1 as the gateway for a dedicated VLAN — such as an IoT segment, a camera network, or a quarantine zone. MikroTik community forums confirm this is a widely adopted convention, with 192.168.60.1 appearing as the gateway for VLAN-tagged interfaces in both home lab and professional deployments.
• Cisco — Cisco's enterprise and SMB routers (including the ISR and RV series) are frequently configured with non-standard subnets like 192.168.60.x for specific network segments. Network administrators use 192.168.60.1 as a gateway for dedicated VLANs, management interfaces, or branch office subnets on Cisco equipment. Cisco's IOS and IOS XE platforms make it straightforward to assign any private IP to any interface.
• Ubiquiti UniFi — Ubiquiti's UniFi Dream Machine, UDM Pro, and USG platforms support multiple virtual networks, and the 192.168.60.0/24 subnet is a popular choice for dedicated VLANs. Administrators assign 192.168.60.1 as the gateway for networks such as IoT, guest Wi-Fi, or VPN segments within the UniFi Network Application.

If your device is a standard consumer router (such as a TP-Link, Netgear, or ASUS home router) and you are seeing 192.168.60.1 as your gateway, it is likely that a previous administrator or ISP technician manually changed the default LAN IP from the factory setting to this address.

Changing Your Router's Password at 192.168.60.1

Regardless of which device is using 192.168.60.1 as its gateway, you should always change the default admin password to protect your network. To do this, log in to the admin panel at http://192.168.60.1 using your current credentials. Once inside, navigate to the administration or system settings section — the exact label varies by platform:

• On MikroTik RouterOS, go to System > Users to change the admin password. You can also use the Winbox application or the terminal command /user set admin password=YourNewPassword.
• On Cisco routers, navigate to Administration > Management > Change Password in the web GUI, or use the CLI command enable secret YourNewPassword in configuration mode.
• On Ubiquiti UniFi, password management is handled through the UniFi Network Application under Settings > Admins & Users, or via your Ubiquiti account at ui.com.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Never leave your gateway at 192.168.60.1 protected only by a default or weak password, especially in environments where multiple users or devices have network access.

Router Username and Password List

Factory Reset for Devices Using 192.168.60.1

If you have forgotten the admin credentials for the device using 192.168.60.1 as its gateway, a factory reset is usually your only option to regain access. The procedure differs depending on the platform:

• MikroTik routers: Locate the Reset button on the device (usually a small pinhole). With the router powered on, hold the Reset button for approximately 5 seconds until the LED starts flashing, then release. The router will reboot and restore its factory configuration. Note that on MikroTik devices, the factory default IP is typically 192.168.88.1, not 192.168.60.1 — so after a reset, you will need to reconnect using that address and reconfigure your 192.168.60.x VLAN setup from scratch.
• Cisco routers (ISR/RV series): The reset procedure varies by model. On most Cisco RV-series routers, hold the Reset button on the back of the device for 10–15 seconds until the power LED flashes. For Cisco ISR routers, you may need to use the console port and perform a password recovery procedure via the ROM monitor (ROMmon) mode. Consult your specific model's documentation on the Cisco support site.
• Ubiquiti UniFi gateways: Hold the Reset button on the UniFi Dream Machine or USG for 10 seconds until the LED changes. The device will reboot to factory defaults. You will then need to re-adopt it in the UniFi Network Application and reconfigure your virtual networks, including any that used the 192.168.60.0/24 subnet.

Always back up your router configuration before performing a factory reset if possible. On MikroTik, you can export your config with /export file=backup. On Cisco, use copy running-config tftp or the web GUI backup option. On UniFi, use the Settings > System > Backup option in the Network Application.

What Is 192.168.60.1 and Why Is It a Private IP?

192.168.60.1 is a Class C private IPv4 address that falls within the 192.168.0.0/16 block reserved for private network use by RFC 1918. This means it is never routed on the public internet — it exists solely within local area networks (LANs). The full private range for Class C addresses spans from 192.168.0.0 to 192.168.255.255, giving network administrators a vast pool of addresses to work with when designing internal networks.

The specific subnet that 192.168.60.1 belongs to is 192.168.60.0/24, which provides 254 usable host addresses (192.168.60.1 through 192.168.60.254). When 192.168.60.1 is assigned as the gateway, connected devices on that subnet will typically receive addresses in the range of 192.168.60.2 through 192.168.60.254 via DHCP. The subnet mask for this range is 255.255.255.0.

One of the key advantages of using the 192.168.60.x subnet — rather than the more common 192.168.1.x or 192.168.0.x — is reduced risk of IP address conflicts. If you connect to a corporate VPN or a remote network that uses 192.168.1.x, your local network on 192.168.60.x will not collide with it, ensuring uninterrupted connectivity. This is one reason why network professionals and home lab enthusiasts deliberately choose less common subnets like 192.168.60.0/24 for their environments.

Related IP Addresses in the 192.168.60.x Subnet

If you are working within the 192.168.60.0/24 subnet, you may also encounter the following addresses. Understanding their roles can help you troubleshoot connectivity issues and design your network more effectively:

• 192.168.60.0 — The network address for this subnet. It identifies the subnet itself and cannot be assigned to any device.
• 192.168.60.1 — The most common gateway address in this subnet, and the subject of this page. This is typically assigned to the router or VLAN interface that provides routing and internet access for devices on the 192.168.60.x network.
• 192.168.60.2 — Sometimes used as an alternative gateway address, particularly in setups where .1 is reserved or already in use. Also commonly assigned as the first DHCP client address.
• 192.168.60.100 — A popular static IP assignment for servers, NAS devices, or other infrastructure within the 192.168.60.x subnet.
• 192.168.60.254 — Occasionally used as an alternative gateway address, particularly by some ISP-supplied modem-routers that prefer the last usable address in a subnet.
• 192.168.60.255 — The broadcast address for this subnet. Data sent to this address is delivered to all devices on the 192.168.60.0/24 network simultaneously. It cannot be assigned to a device.

Other commonly used private gateway addresses outside this subnet that you may want to reference include 192.168.1.254, 192.168.100.1, 192.168.10.1, and 10.0.0.1.

Frequently Asked Questions About 192.168.60.1

What router uses 192.168.60.1 as its default IP?

192.168.60.1 is not the factory default of a single consumer router brand. It is most commonly found on MikroTik routers configured with VLAN segmentation, Cisco enterprise and SMB equipment, and Ubiquiti UniFi gateways where the 192.168.60.0/24 subnet has been assigned to a specific virtual network. If you are seeing this address on a standard home router, it has likely been manually configured by a previous administrator or your ISP.

How do I log in to 192.168.60.1?

Open a web browser on a device connected to the same network and navigate to http://192.168.60.1. Enter your admin username and password on the login page. If you have not changed the defaults, check the label on your device. Common defaults are admin / admin or admin / password. On MikroTik devices, the default username is admin with a blank password (on older firmware) or a password printed on the device label (on newer units).

Why can't I reach 192.168.60.1 from my computer?

The most likely reason is that your computer is not on the 192.168.60.x subnet. Run ipconfig (Windows) or ip route (Linux/macOS terminal) to check your current default gateway. If it shows a different address, you are on a different network segment. On VLAN-based setups using MikroTik or Ubiquiti, you must be connected to the specific VLAN that uses 192.168.60.1 as its gateway. Also check that no VPN software is active, as VPNs can redirect local traffic.

Is 192.168.60.1 safe to use as a gateway?

Yes, 192.168.60.1 is a perfectly valid and safe private IP address to use as a gateway. Because it falls in the less commonly used 192.168.60.x range, it actually offers a slight advantage over 192.168.1.1 or 192.168.0.1 in terms of avoiding IP conflicts with VPNs and other networks. As with any gateway, make sure you change the default admin password and keep your router firmware up to date to maintain security.

What is the subnet mask for 192.168.60.1?

The standard subnet mask for the 192.168.60.0/24 network is 255.255.255.0. This gives you 254 usable host addresses, from 192.168.60.1 to 192.168.60.254. The network address is 192.168.60.0 and the broadcast address is 192.168.60.255.

How do I reset a MikroTik router using 192.168.60.1?

Hold the Reset button on your MikroTik device for approximately 5 seconds while it is powered on, until the LED begins to flash. Release the button and allow the device to reboot. After the reset, the router will return to its factory default IP of 192.168.88.1 — not 192.168.60.1. You will need to reconnect using that address and reconfigure your VLAN and IP settings, including reassigning 192.168.60.1 to your desired interface.