192.168.50.2 Admin Login

192.168.50.2 is a private IPv4 address belonging to the 192.168.50.0/24 subnet — a Class C private IP range. It is most commonly encountered as the first DHCP-assigned address on networks where the router's default gateway is 192.168.50.1. The most prominent brand associated with this subnet is ASUS, whose newer and higher-end router models — including the RT-AC86U, RT-AX86U, RT-AX88U, ZenWiFi AX (XT8), ZenWiFi Pro ET12, and RT-BE96U — ship with 192.168.50.1 as their default LAN gateway, making 192.168.50.2 the very first address handed out by the DHCP server to a connected device. Sweex also uses the 192.168.50.x subnet on select models such as the LW050 and LW050V2. Because 192.168.50.2 sits just one step above the gateway, it is frequently reserved as a static IP for trusted devices like network-attached storage (NAS) drives, printers, or secondary access points. Other widely used private gateway addresses in neighboring subnets include 192.168.1.254 and 192.168.0.1.

How to Access 192.168.50.2

To reach a device or admin panel configured at 192.168.50.2, open your preferred web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.50.2 directly into the address bar. Do not enter it into a search engine, as that will return web results rather than your device's login page. Press Enter and you should be presented with a login prompt.

Keep in mind that 192.168.50.2 is not typically the router's own admin panel address — that role belongs to 192.168.50.1 on ASUS and Sweex networks. Instead, 192.168.50.2 is most often the IP address of the first client device on the network, or a device that has been manually assigned this static address. Common examples include:

• A NAS (Network-Attached Storage) device with a fixed IP for reliable file sharing access
• A network printer assigned 192.168.50.2 so it is always reachable at the same address
• A secondary router or access point operating in bridge or AP mode
• A smart home hub or media server that requires a predictable local address

Because 192.168.50.2 is a private IP address, it is only reachable from within your local network — it is completely inaccessible from the public internet. If you need to access a device at 192.168.50.2 remotely, you would need to configure port forwarding or a VPN on your ASUS router at 192.168.50.1.

If You Can't Access 192.168.50.2

If typing http://192.168.50.2 into your browser does not load a login page or device interface, there are several things to check before concluding the address is wrong:

• Verify your network subnet: On Windows, open Command Prompt (Start > type cmd > press Enter) and run ipconfig /all. Look for the Default Gateway field. If it shows 192.168.50.1, you are on the correct subnet and 192.168.50.2 should be reachable. On macOS or Linux, run netstat -nr or check System Preferences > Network.
• Confirm a device is actually assigned 192.168.50.2: Log in to your ASUS router at http://192.168.50.1 and navigate to the Network Map or DHCP Leases section to see which devices are currently assigned IPs. If no device holds 192.168.50.2, the address is simply unoccupied.
• Check your physical connection: Make sure your computer is connected to the router via Wi-Fi or an Ethernet cable. You cannot reach any address in the 192.168.50.x range if you are not on the same local network.
• Try HTTP instead of HTTPS: Some browsers automatically redirect to HTTPS. Always use http://192.168.50.2 (not https), as most local devices do not have SSL certificates installed.
• Disable VPN or proxy software: Active VPN clients or proxy settings can reroute your traffic away from the local subnet. Temporarily disable them and try again.
• Ping the address: Open Command Prompt and type ping 192.168.50.2. If you receive replies, the device is online and reachable — the issue may be browser-specific. If the ping times out, the device is either offline or not assigned that IP.

Router Brands That Use the 192.168.50.x Subnet

Unlike the more common 192.168.1.x or 192.168.0.x subnets used by dozens of manufacturers, the 192.168.50.0/24 range is associated with a much smaller and more specific set of brands. Understanding which brands operate in this subnet helps you identify your gateway and troubleshoot your network more effectively.

ASUS

ASUS is by far the most prominent brand associated with the 192.168.50.x subnet. While older ASUS models such as the RT-AC68U defaulted to 192.168.1.1, ASUS shifted many of its newer and higher-end models to use 192.168.50.1 as the default LAN gateway, placing 192.168.50.2 as the first DHCP-assigned address in the pool. ASUS router models confirmed to use the 192.168.50.x subnet include:

• ASUS RT-AC86U
• ASUS RT-AX86U / RT-AX86S
• ASUS RT-AX88U
• ASUS RT-AX86U Pro
• ASUS RT-AXE7800
• ASUS RT-BE96U
• ASUS ZenWiFi AX (XT8)
• ASUS ZenWiFi Pro ET12
• ASUS GT-AX11000 (ROG Rapture, select firmware versions)

On ASUS routers, the admin panel is accessible at http://192.168.50.1 or via the hostname router.asus.com. The default DHCP pool on these models typically runs from 192.168.50.2 to 192.168.50.254, meaning the very first device that connects to your ASUS router will receive 192.168.50.2. The ASUS admin interface (ASUSWRT) is feature-rich and includes AI Protection, Traffic Analyzer, VPN server/client, Adaptive QoS, and a robust port forwarding module.

Sweex

Sweex, a European networking brand, uses the 192.168.50.x subnet on its LW050 and LW050V2 Wireless 54G router models. These devices default to 192.168.50.1 as the gateway, placing 192.168.50.2 within the DHCP range. The default login credentials for Sweex devices are unique: Username: sweex / Password: mysweex.

Assigning 192.168.50.2 as a Static IP

One of the most practical uses of 192.168.50.2 on an ASUS or Sweex network is assigning it as a permanent static IP to a specific device. This ensures that a critical device — such as a NAS, printer, or smart home hub — always receives the same address and is always reachable at 192.168.50.2, regardless of DHCP lease renewals or router reboots.

There are two ways to assign 192.168.50.2 as a static address:

Method 1: DHCP Reservation on Your ASUS Router

This is the recommended approach, as it requires no manual configuration on the device itself:

1. Log in to your ASUS router at http://192.168.50.1 using your admin credentials (default: admin / admin).
2. Navigate to LAN in the left-hand menu, then click the DHCP Server tab.
3. Scroll down to the Manually Assigned IP around the DHCP list section.
4. Enter the MAC address of the device you want to assign 192.168.50.2 to, then type 192.168.50.2 in the IP address field.
5. Click the + button to add the reservation, then click Apply.
6. Reboot the target device so it requests and receives its reserved IP from the DHCP server.

Method 2: Manual Static IP on the Device

You can also configure the device itself to always use 192.168.50.2:

• IP Address: 192.168.50.2
• Subnet Mask: 255.255.255.0
• Default Gateway: 192.168.50.1
• DNS Server: 192.168.50.1 (or a public DNS such as 8.8.8.8)

Be sure to exclude 192.168.50.2 from your DHCP pool in the router settings to prevent address conflicts. On ASUS routers, you can adjust the DHCP range start address to 192.168.50.3 or higher under LAN > DHCP Server.

Factory Reset Procedure for Routers Using the 192.168.50.x Subnet

If you have forgotten your admin password, or your router is behaving unexpectedly, a factory reset will restore all settings — including the default gateway and DHCP range starting at 192.168.50.2 — back to their out-of-the-box state. Note that a factory reset will erase all custom configurations, including your Wi-Fi name, password, port forwarding rules, and any static IP reservations.

ASUS Routers (RT-AX86U, RT-BE96U, ZenWiFi XT8, etc.)

1. Power off your ASUS router completely by unplugging it.
2. Locate the Reset button — typically a small pinhole on the rear or bottom of the device.
3. Using a pin, paperclip, or SIM ejector tool, press and hold the Reset button.
4. While holding the Reset button, plug the router back in to power it on.
5. Continue holding the Reset button for approximately 10 seconds until the power LED begins flashing rapidly.
6. Release the button and wait 1–2 minutes for the router to fully reboot.
7. Once rebooted, navigate to http://192.168.50.1 and log in with the default credentials: admin / admin. Your DHCP pool will be restored to 192.168.50.2–192.168.50.254.

For ASUS ZenWiFi mesh nodes (e.g., XT8), an alternative reset method involves holding the WPS button while powering on the unit, then releasing it once the power LED illuminates and waiting for the device to complete its reboot cycle.

Sweex LW050 / LW050V2

1. Disconnect the router from the power supply.
2. Locate the Reset button on the rear panel of the device.
3. Press and hold the Reset button while reconnecting the power cable.
4. Hold for approximately 10 seconds until the LEDs flash.
5. Release the button and allow the router to reboot fully.
6. Access the admin panel at http://192.168.50.1 using the default credentials: sweex / mysweex.

Changing Your Router Password on a 192.168.50.x Network

Leaving your router's admin password at its factory default is a significant security risk. Anyone connected to your 192.168.50.x network could potentially access your router's settings at 192.168.50.1 and make unauthorized changes — including altering your DNS, opening ports, or locking you out entirely. Here's how to update your admin password on the brands that use this subnet:

On ASUS Routers

1. Log in to http://192.168.50.1 with your current credentials.
2. Navigate to Administration in the left-hand sidebar.
3. Click the System tab.
4. Under Router Login Name and Router Login Password, enter your new credentials.
5. Click Apply to save the changes.

On Sweex LW050 / LW050V2

1. Log in to http://192.168.50.1 using sweex / mysweex.
2. Navigate to the Administration or Management section.
3. Locate the password change field, enter your new password, and confirm it.
4. Click Save or Apply.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Avoid reusing your Wi-Fi password as your admin password.

Router Username and Password List

What Is 192.168.50.2 as a Private IP Address?

192.168.50.2 is a private IPv4 address in the Class C range, defined by RFC 1918. This means it is reserved exclusively for use within private local area networks (LANs) and is never routed over the public internet. Every device on your home or office network — whether connected via Wi-Fi or Ethernet — receives a private IP address from the router's DHCP server, and 192.168.50.2 is the first address in the pool on networks using the 192.168.50.x subnet.

The 192.168.50.0/24 subnet supports up to 254 usable host addresses, ranging from 192.168.50.1 (the gateway, used by ASUS and Sweex routers) through 192.168.50.254. Here is an example of how devices might be assigned addresses on such a network:

• The ASUS router holds 192.168.50.1 as the gateway.
• The first device to connect (e.g., a laptop) receives 192.168.50.2.
• The second device (e.g., a smartphone) receives 192.168.50.3.
• A NAS device manually assigned a static IP might use 192.168.50.2 permanently.

Private IP addresses like 192.168.50.2 are essential to how your local network functions. Your router uses Network Address Translation (NAT) to map all of these private addresses to a single public IP address when communicating with the internet, keeping your internal network structure hidden and secure.

It is worth noting that 192.168.50.2 is not the same as your public IP address. Your public IP is assigned by your Internet Service Provider (ISP) and is visible to websites and online services. Your private IP — 192.168.50.2 — is only visible within your local network and is used by your router to direct traffic to the correct device.

Related IP Addresses in the 192.168.50.x Subnet

The 192.168.50.0/24 subnet contains 254 usable host addresses. While 192.168.50.2 is the most commonly DHCP-assigned address on ASUS and Sweex networks, several other addresses in this range serve specific roles or are worth knowing about:

• 192.168.50.1 — The default gateway address used by ASUS (RT-AC86U, RT-AX86U, RT-AX88U, ZenWiFi XT8, RT-BE96U) and Sweex (LW050, LW050V2). This is the address you use to access your router's admin panel.
• 192.168.50.2 — The current IP. Typically the first DHCP-assigned client address, or a static IP reserved for a trusted device such as a NAS or printer.
• 192.168.50.3 – 192.168.50.100 — Common range for additional DHCP-assigned client devices on the network.
• 192.168.50.100 – 192.168.50.200 — Often used as a dedicated DHCP pool range on networks where lower addresses are reserved for static assignments.
• 192.168.50.254 — The last usable host address in the subnet, sometimes used as an alternative gateway or management IP on certain configurations.

If you are managing a network in the 192.168.50.x range and need to reference other common private gateway addresses used by different router brands, you may also find these pages useful: 192.168.0.1, 192.168.1.254, 192.168.2.1, 192.168.8.1, and 10.0.0.1.

Frequently Asked Questions About 192.168.50.2

What device uses 192.168.50.2?

On networks where an ASUS router (such as the RT-AX86U, ZenWiFi XT8, or RT-BE96U) or a Sweex LW050 is the gateway at 192.168.50.1, the address 192.168.50.2 is typically assigned to the first device that connects via DHCP — such as a laptop, desktop, or smartphone. It is also commonly reserved as a static IP for a NAS drive, network printer, or secondary access point that needs a predictable, permanent address.

Is 192.168.50.2 the same as my router's admin page?

No. On ASUS and Sweex networks using the 192.168.50.x subnet, the router's admin panel is located at 192.168.50.1 — not 192.168.50.2. The address 192.168.50.2 belongs to a client device on the network. To access your ASUS router's settings, navigate to http://192.168.50.1 or type router.asus.com into your browser.

Can two devices share the IP address 192.168.50.2?

No. Assigning 192.168.50.2 to more than one device on the same network will cause an IP address conflict, resulting in connectivity issues for both devices. Your ASUS router's DHCP server is designed to prevent this automatically, but conflicts can occur if you manually assign 192.168.50.2 as a static IP on a device while the DHCP pool still includes that address. Always exclude statically assigned addresses from your DHCP range in the router settings.

How do I find out which device is using 192.168.50.2?

Log in to your ASUS router at http://192.168.50.1 using your admin credentials. Navigate to the Network Map on the main dashboard or go to LAN > DHCP Server and scroll to the DHCP Leases list. This will show you every device currently assigned an IP address on your 192.168.50.x network, including the device holding 192.168.50.2, along with its hostname and MAC address.

What is the subnet mask for 192.168.50.2?

The standard subnet mask for the 192.168.50.0/24 network is 255.255.255.0. This means all addresses from 192.168.50.1 to 192.168.50.254 are on the same local network, with 192.168.50.0 as the network address and 192.168.50.255 as the broadcast address. Your ASUS or Sweex router at 192.168.50.1 uses this subnet mask by default.

Why does my ASUS router use 192.168.50.x instead of 192.168.1.x?

ASUS made a deliberate decision to shift newer, higher-end models to the 192.168.50.x subnet to reduce the likelihood of IP conflicts when connecting to corporate VPNs or other networks that commonly use the 192.168.1.x range. If your ASUS router defaults to 192.168.50.1 as its gateway and 192.168.50.2 as the first DHCP address, this is by design. You can change the LAN IP back to 192.168.1.1 under LAN > LAN IP in the ASUSWRT admin panel if preferred.