192.168.30.1 Admin Login

Some router manufacturers — most notably Motorola and OutdoorRouter — use 192.168.30.1 as their default gateway IP address. Motorola assigned this address to its WE800G Wireless Ethernet Bridge, while OutdoorRouter uses it across its EZR33 and EZR3X series of outdoor 4G LTE routers. It is a Class C private IPv4 address that sits within the 192.168.30.0/24 subnet, giving your local network up to 254 usable host addresses (192.168.30.1 through 192.168.30.254). Because it falls inside the RFC 1918 private address space, 192.168.30.1 is never routed across the public internet — it exists solely to manage traffic inside your home or office network. Other widely used default gateways in the same private range include 192.168.0.1, 192.168.1.254, and 192.168.2.1.

How to Access 192.168.30.1

To reach your router's admin panel, open any web browser on a device that is connected to your network — either via Wi-Fi or an Ethernet cable — and type http://192.168.30.1 directly into the address bar. Do not use a search engine; paste the address straight into the URL bar and press Enter. You should be greeted by a login page within a few seconds.

Once you are on the login page, enter your router's username and password. If you have never changed these credentials, refer to the default login details for your specific device:

• Motorola WE800G: Username admin / Password motorola
• OutdoorRouter EZR33 / EZR3X: Username root / Password root or admin

After logging in, you can change your Wi-Fi network name (SSID) and password, configure port forwarding, update firmware, set up a guest network, and adjust many other settings. Because 192.168.30.1 is a private address, any device on your local network could technically be assigned this IP — so make sure only your router uses it to avoid an IP address conflict.

If You Can't Access 192.168.30.1

If typing http://192.168.30.1 into your browser returns an error or a blank page, work through the following checks before assuming the address is wrong:

1. Confirm your gateway address. On Windows, open the Command Prompt (Start > type cmd > Enter) and run ipconfig /all. Look for the Default Gateway field. On macOS, go to System Settings > Network > your active connection > Details. If the gateway shown is not 192.168.30.1, use the address that is listed instead, or check our guide to find your router IP address.
2. Check your cable or Wi-Fi connection. You must be connected to the same network as the router. If you are on a different subnet or VLAN, the browser request will not reach 192.168.30.1.
3. Disable browser extensions and VPNs. Ad blockers, proxy extensions, and active VPN tunnels can intercept or reroute the request. Temporarily disable them and try again.
4. Try a different browser or incognito mode. Cached DNS entries or browser settings can sometimes block local IP access.
5. Power-cycle the router. Unplug the power adapter, wait 30 seconds, then plug it back in. Allow 2–3 minutes for the router to fully boot before trying 192.168.30.1 again.
6. Check for IP conflicts. If another device on your network has been manually assigned 192.168.30.1, the router's admin page may be unreachable. Disconnect other devices one by one and retry.

Changing Your Router's Password at 192.168.30.1

Keeping the factory-default password on any router is a serious security risk. Anyone who knows the brand of your device can look up the default credentials and gain full control of your network. Here is how to update your password once you are logged in to 192.168.30.1:

• Motorola WE800G: After logging in with the default credentials (admin / motorola), navigate to the Administration or Management section of the interface. Look for a Change Password field, enter your new password twice to confirm, and save the changes.
• OutdoorRouter EZR33 / EZR3X: Log in to http://192.168.30.1 with username root, then go to System > Administration. You will find the router password field there. Enter your new password, confirm it, and click Save.

Choose a strong password that is at least 12 characters long and combines uppercase letters, lowercase letters, numbers, and symbols. Avoid using your Wi-Fi password as your admin password — they should always be different. After saving, you will be prompted to log in again with the new credentials.

Router Username and Password List

Router Brands That Use 192.168.30.1

Not every router manufacturer uses 192.168.30.1 — it is a less common default gateway compared to addresses like 192.168.0.1 or 10.0.0.1. The confirmed brands and models that ship with 192.168.30.1 as their default gateway are:

• Motorola WE800G — A wireless Ethernet bridge that uses 192.168.30.1 as its default IP. Default credentials: username admin, password motorola. Note that the related Motorola WR850G uses a different default IP, but its documentation explicitly references the WE800G's 192.168.30.1 address.
• OutdoorRouter EZR33 / EZR33L — An outdoor 4G LTE router designed for remote and industrial deployments. It ships with 192.168.30.1 as its gateway, a DHCP pool of 192.168.30.100–254, and a subnet mask of 255.255.255.0. Default credentials: username root, password root or admin.
• OutdoorRouter EZR3X series — The broader EZR3X product family from OutdoorRouter also defaults to 192.168.30.1 with the same DHCP configuration as the EZR33.

If your router is not listed above but you are still reaching an admin panel at 192.168.30.1, it is likely that a previous administrator manually changed the default gateway from a more common address (such as 192.168.1.254 or 192.168.100.1) to 192.168.30.1 for network segmentation or VLAN purposes.

Factory Reset Instructions for Routers Using 192.168.30.1

If you have forgotten your admin password or your router is behaving unexpectedly, a factory reset will restore all settings — including the default gateway 192.168.30.1 and the original login credentials. Warning: a factory reset erases all custom configurations, including your Wi-Fi name, password, port forwarding rules, and any other changes you have made.

Motorola WE800G

1. Make sure the router is powered on.
2. Locate the small Reset button on the back or underside of the unit.
3. Use a straightened paperclip or a similar thin object to press and hold the Reset button for 10 seconds.
4. Release the button. The router will reboot automatically.
5. Wait 2–3 minutes, then navigate to http://192.168.30.1 and log in with username admin and password motorola.

OutdoorRouter EZR33 / EZR3X

OutdoorRouter recommends a soft reset whenever possible, as it is safer and less disruptive:

1. Log in to http://192.168.30.1.
2. Go to System > Backup / Flash Firmware and select the option to perform a factory reset from within the interface.

If you cannot access the admin panel, perform a hard reset:

1. Ensure the router is powered on (system indicator light is green).
2. Press and hold the physical Reset button for 5 seconds while the router is running.
3. Release the button and wait 2–3 minutes for the router to reboot.
4. Reconnect to the default Wi-Fi network (Outdoor-WiFi-xxxxxx) and navigate to http://192.168.30.1. Log in with username root and password root or admin.

What Is 192.168.30.1 and Why Does It Matter?

192.168.30.1 is a Class C private IPv4 address defined by RFC 1918. The entire 192.168.0.0/16 block — which includes 192.168.30.1 — is reserved exclusively for private networks and is never assigned to any device on the public internet. This means you can use 192.168.30.1 as a gateway on your local network without any risk of conflicting with a public server or website.

When your router uses 192.168.30.1 as its gateway, it automatically creates the 192.168.30.0/24 subnet. Every device that connects to your network receives a unique private IP address within that range — typically assigned automatically by the router's built-in DHCP server. For example, on an OutdoorRouter EZR33, the DHCP pool runs from 192.168.30.100 to 192.168.30.254, so connected devices receive addresses like 192.168.30.100, 192.168.30.101, and so on.

The address 192.168.30.1 is also commonly used in enterprise and VLAN environments. Network administrators often assign the 192.168.30.0/24 subnet to a specific VLAN (for example, VLAN 30) to logically separate traffic — such as isolating IoT devices, IP cameras, or guest users from the main corporate network. In these setups, 192.168.30.1 acts as the default gateway for that particular VLAN segment.

Related IPs in the same 192.168.30.0/24 subnet that you may encounter include:

• 192.168.30.2 – 192.168.30.99: Often reserved for static device assignments such as printers, NAS drives, IP cameras, or managed switches.
• 192.168.30.100 – 192.168.30.254: Typically the DHCP pool range for dynamically assigned client devices.
• 192.168.30.255: The broadcast address for the subnet — not assignable to any device.
• 192.168.30.0: The network address — also not assignable to any device.

Frequently Asked Questions About 192.168.30.1

What is 192.168.30.1 used for?

192.168.30.1 is used as the default gateway IP address for certain routers, most notably the Motorola WE800G and the OutdoorRouter EZR33/EZR3X series. It is also the address you type into your browser to access your router's admin panel and change settings like your Wi-Fi password, SSID, and port forwarding rules. In enterprise networks, it frequently serves as the gateway for a dedicated VLAN 30 subnet.

Is 192.168.30.1 a public or private IP address?

192.168.30.1 is a private IP address. It belongs to the 192.168.0.0/16 block reserved by RFC 1918 for use in private networks. It cannot be accessed from the internet and is only reachable by devices connected to the same local network.

What is the default username and password for 192.168.30.1?

The default credentials depend on your router model. For the Motorola WE800G, use username admin and password motorola. For OutdoorRouter EZR33 and EZR3X devices, use username root and password root or admin. If these do not work, the credentials may have been changed by a previous administrator — in that case, you will need to perform a factory reset to restore the defaults.

Why can't I open 192.168.30.1 in my browser?

The most common reasons are: (1) your device is not connected to the network that uses 192.168.30.1 as its gateway, (2) a VPN or proxy is intercepting the request, (3) another device on the network has been assigned the same IP address, causing a conflict, or (4) 192.168.30.1 is simply not your router's gateway — run ipconfig /all on Windows or check your network settings on macOS/Linux to confirm the correct gateway address.

Can I change my router's IP from 192.168.30.1 to something else?

Yes. Log in to your router's admin panel at http://192.168.30.1, navigate to the LAN or Network settings section, and update the IP address to your preferred value (for example, 192.168.1.1 or 192.168.10.1). After saving, your router will reboot and you will need to use the new address to access the admin panel. Make sure the new address does not conflict with any other device on your network.

What subnet does 192.168.30.1 belong to?

192.168.30.1 belongs to the 192.168.30.0/24 subnet, which has a subnet mask of 255.255.255.0. This subnet supports up to 254 usable host addresses, ranging from 192.168.30.1 to 192.168.30.254. The network address is 192.168.30.0 and the broadcast address is 192.168.30.255.

Is 192.168.30.1 safe to use as a gateway?

Yes, 192.168.30.1 is completely safe to use as a private gateway address. Like all RFC 1918 addresses, it is non-routable on the public internet. However, you should always change the default admin password after logging in for the first time to prevent unauthorized access to your router's settings at 192.168.30.1.