192.168.225.1 Admin Login

192.168.225.1 is a private Class C IPv4 address primarily used as the default gateway by mobile Wi-Fi hotspot devices from Jio (Reliance Jio Infocomm), as well as networking hardware from AM Telecom and Foxcomm. If you own a JioFi 3 (JMR540), JioFi M2, JCO4032, or the AR5511, then 192.168.225.1 is the address you need to access your device's admin panel. It sits within the 192.168.225.0/24 subnet — a less commonly seen range compared to the more popular 192.168.1.254 or 192.168.0.1, but it functions in exactly the same way as a private, non-routable gateway address for your local network.

How to Access 192.168.225.1

To reach your router or hotspot's admin panel at 192.168.225.1, follow these steps:

1. Make sure your device (laptop, phone, or tablet) is connected to the same Wi-Fi network broadcast by your JioFi or AM Telecom / Foxcomm device — either wirelessly or via an Ethernet cable.
2. Open any web browser (Chrome, Firefox, Edge, or Safari) and type http://192.168.225.1 directly into the address bar. Do not type it into a search engine — it must go into the address bar.
3. Press Enter. The router's login page will load within a few seconds.
4. Enter your username and password. For most JioFi devices, the default credentials are Username: administrator and Password: administrator. Some models may use admin / admin. Check the sticker on the back or inside the battery compartment of your device for the exact defaults.
5. Once logged in, you can manage your Wi-Fi SSID, password, data usage, connected devices, firmware updates, and security settings.

Because 192.168.225.1 is a private IPv4 address, it is only reachable from within your local network. No one on the internet can access it directly, which makes it inherently safe from external intrusion — though you should still protect it with a strong admin password.

If You Can't Access 192.168.225.1

If typing http://192.168.225.1 into your browser returns an error or a blank page, work through the following checks before assuming the address is wrong:

• Confirm your gateway address: On Windows, open Command Prompt (Start > type cmd > press Enter) and run ipconfig /all. Look for the Default Gateway field under your active network adapter. It should read 192.168.225.1. On a Mac, go to System Settings > Network > your active connection > Details > TCP/IP. On Android or iOS, tap the connected Wi-Fi network and view its details.
• Check your connection: Your device must be connected to the JioFi or AM Telecom / Foxcomm hotspot — not to a different Wi-Fi network or mobile data. Phones sometimes switch to cellular automatically; disable mobile data temporarily and retry.
• Try a wired connection: If your device supports it, plug an Ethernet cable directly from your computer into the router's LAN port. Wired connections are more reliable for admin panel access.
• Clear your browser cache or try a different browser. Some cached redirects can interfere with local IP access.
• Disable VPN software: Active VPN connections reroute your traffic and can prevent access to local gateway addresses like 192.168.225.1.
• Disable browser extensions: Ad blockers or proxy extensions can sometimes block local IP addresses. Try opening an incognito/private window.
• Check if the IP was changed: A previous administrator may have changed the default gateway. If you cannot determine the new IP, a factory reset (see below) will restore 192.168.225.1 as the default.

If none of the above resolves the issue, consult our guide on how to find your router IP address for a full walkthrough.

Router Brands That Use 192.168.225.1

Unlike the more universal gateway addresses such as 192.168.0.1 or 10.0.0.1, the address 192.168.225.1 is associated with a specific set of devices. Here is what you need to know about each:

Jio (Reliance Jio Infocomm)

Jio is India's largest telecom operator and manufactures a range of 4G LTE mobile Wi-Fi hotspot devices under the JioFi brand. Several JioFi models use 192.168.225.1 as their default admin gateway, including the JioFi 3 (JMR540 / JMR541), the JioFi M2, and the JCO4032. These compact, battery-powered devices create a portable Wi-Fi hotspot using a Jio SIM card and allow up to 10–32 devices to connect simultaneously. The admin panel at 192.168.225.1 lets you view data usage, manage connected devices, change your Wi-Fi name and password, and update firmware.

Default login credentials for JioFi devices at 192.168.225.1:

• Username: administrator  |  Password: administrator
• Some models may use admin / admin
• Always check the label inside the battery compartment for your specific model's defaults

AM Telecom

AM Telecom is a South Korean telecommunications equipment manufacturer that produces LTE routers and mobile broadband devices, including the AR5511 model. The AR5511 uses 192.168.225.1 as its default gateway. AM Telecom devices are commonly deployed by ISPs and mobile carriers as CPE (Customer Premises Equipment). If you are using an AM Telecom device, access the admin panel at 192.168.225.1 and use the credentials provided by your ISP or printed on the device label.

Foxcomm

Foxcomm produces networking and broadband devices that also use 192.168.225.1 as their default gateway. If you have a Foxcomm device, navigate to 192.168.225.1 in your browser and use the default credentials found on the device's label or in the user manual. Common defaults include admin / admin or admin / password.

Changing Your Admin Password at 192.168.225.1

One of the most important things you should do after accessing your device at 192.168.225.1 is change the default admin password. Devices like the JioFi 3 and JioFi M2 ship with well-known default credentials (administrator / administrator), which means anyone connected to your Wi-Fi network could potentially access your admin panel and change your settings.

To change your admin password on a JioFi device:

1. Log in to http://192.168.225.1 using your current credentials.
2. Navigate to the Settings or Account section of the admin panel.
3. Look for Change Password or Admin Password.
4. Enter your current password, then type your new password twice to confirm.
5. Click Save or Apply. The device may log you out and prompt you to log back in with the new password.

Choose a strong password that is at least 8–12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and special characters. Do not reuse your Wi-Fi password as your admin password — keep them separate for better security.

Router Username and Password List

How to Factory Reset a Device Using 192.168.225.1

If you have forgotten your admin password or your device is behaving unexpectedly, a factory reset will restore all settings — including the default gateway of 192.168.225.1 and the original login credentials. Note that a factory reset will erase all custom configurations, including your Wi-Fi name, password, and any port forwarding or APN settings you have configured.

Factory Reset for JioFi 3 (JMR540 / JMR541)

1. Make sure your JioFi 3 is powered on and has sufficient battery charge (at least 50% recommended).
2. Remove the back cover of the device. You do not need to remove the battery.
3. Locate the small pinhole reset button inside the battery compartment area.
4. Insert a straightened paperclip or SIM ejector pin into the pinhole and press and hold for 10 seconds or more.
5. All indicator lights will turn red and then go off. Release the pin.
6. The device will automatically reboot. Wait for it to fully restart (approximately 60–90 seconds).
7. Once restarted, connect to the default JioFi Wi-Fi network (SSID and password are printed on the device label).
8. Navigate to http://192.168.225.1 and log in with administrator / administrator.

Factory Reset for JioFi M2

1. Power on the JioFi M2 device.
2. Locate the reset pinhole on the device body (check the side or back panel).
3. Use a pin or paperclip to press and hold the reset button for 5–10 seconds until the lights change.
4. Release and allow the device to reboot fully.
5. Reconnect to the default Wi-Fi and access 192.168.225.1 with the default credentials.

Factory Reset for AM Telecom AR5511 and Foxcomm Devices

1. Ensure the device is powered on.
2. Locate the RESET button on the back or bottom panel of the device.
3. Press and hold the reset button for 10–15 seconds using a pin or paperclip.
4. Release when the indicator lights flash or change color.
5. Wait for the device to reboot, then access 192.168.225.1 with the default credentials from the device label.

What Is 192.168.225.1 as a Private IP Address?

192.168.225.1 is a Class C private IPv4 address, defined under RFC 1918 as part of the reserved 192.168.0.0/16 block. This entire range — from 192.168.0.0 to 192.168.255.255 — is set aside exclusively for use within private local area networks (LANs). Addresses in this range are not routable on the public internet, meaning no traffic destined for 192.168.225.1 will ever travel beyond your local network or router.

When a device like the JioFi 3 or AM Telecom AR5511 uses 192.168.225.1 as its gateway, it means that device is the central hub of your local network. Every other device that connects to it — your phone, laptop, tablet, or smart TV — receives a dynamically assigned IP address from the same 192.168.225.x subnet via DHCP. For example:

• Your smartphone might receive 192.168.225.2
• Your laptop might receive 192.168.225.3
• Your tablet might receive 192.168.225.4

The router at 192.168.225.1 acts as the traffic controller — it receives data requests from these devices, forwards them to the internet using its public IP address (assigned by your ISP), and then routes the responses back to the correct device on your local network. This process is called Network Address Translation (NAT).

The 192.168.225.x subnet is less commonly used than subnets like 192.168.1.x or 192.168.0.x, which is why you are more likely to encounter 192.168.225.1 on specialized devices like mobile hotspots rather than standard home routers. Other commonly used gateway addresses in the broader 192.168.x.x space include 192.168.0.1, 192.168.2.1, 192.168.8.1, and 192.168.10.1.

Related IP Addresses in the 192.168.225.x Subnet

The 192.168.225.0/24 subnet contains 254 usable host addresses, ranging from 192.168.225.1 to 192.168.225.254. While 192.168.225.1 is the gateway (router) address, the remaining addresses in this range are typically assigned to client devices by the router's DHCP server. Here are some of the related addresses you may encounter within this subnet:

• 192.168.225.1 — Default gateway (your JioFi or AM Telecom / Foxcomm router)
• 192.168.225.2 – 192.168.225.254 — DHCP pool for connected client devices
• 192.168.225.100 — Sometimes used as a static IP for a primary connected device or network printer
• 192.168.225.255 — Broadcast address for the subnet (not assignable to devices)

If you need to assign a static IP address to a specific device on your network (such as a printer, NAS drive, or gaming console), log in to your admin panel at 192.168.225.1 and look for the DHCP Reservation or Static IP settings. This ensures that device always receives the same IP address, which is useful for port forwarding and remote access configurations.

Frequently Asked Questions About 192.168.225.1

What devices use 192.168.225.1 as their default gateway?

The most well-known devices that use 192.168.225.1 as their default gateway are JioFi mobile hotspot devices from Reliance Jio, including the JioFi 3 (JMR540/JMR541), JioFi M2, and JCO4032. Additionally, the AM Telecom AR5511 and certain Foxcomm networking devices also use this address. If you have one of these devices and want to access its settings, simply navigate to 192.168.225.1 in your browser while connected to the device's network.

What are the default login credentials for 192.168.225.1?

For JioFi devices, the most common default credentials at 192.168.225.1 are Username: administrator and Password: administrator. Some models may use admin / admin. For AM Telecom and Foxcomm devices, try admin / admin or admin / password as starting points. Always check the label on the back or inside the battery compartment of your specific device, as credentials can vary by model and firmware version.

Is 192.168.225.1 safe to access?

Yes, accessing 192.168.225.1 is completely safe. It is a private IP address that is only reachable from within your local network — it cannot be accessed from the internet. However, you should always protect your admin panel with a strong, unique password to prevent unauthorized access from anyone connected to your Wi-Fi network.

Why can't I reach 192.168.225.1 in my browser?

The most common reasons you cannot reach 192.168.225.1 are: (1) your device is not connected to the correct Wi-Fi network (e.g., your phone switched to mobile data), (2) you have a VPN active that is rerouting your traffic, (3) the default gateway has been changed from 192.168.225.1 to a different address, or (4) you typed the address into a search bar instead of the browser's address bar. Run ipconfig /all on Windows or check your network settings on mobile to confirm your current default gateway.

How do I reset my JioFi device to restore 192.168.225.1?

To restore your JioFi 3 or JioFi M2 to factory defaults (including the 192.168.225.1 gateway and default credentials), remove the back cover and use a pin to press and hold the pinhole reset button for 10 seconds or more. The device will reboot automatically. Once it restarts, connect to the default Wi-Fi network and access 192.168.225.1 with the default credentials (administrator / administrator). For AM Telecom and Foxcomm devices, press and hold the RESET button on the device body for 10–15 seconds.

Can I change the 192.168.225.1 gateway address to something else?

Yes, most devices that use 192.168.225.1 allow you to change the LAN IP address through the admin panel. Log in to 192.168.225.1, navigate to LAN Settings or Network Settings, and update the IP address to your preferred value (e.g., 192.168.1.1). Be aware that once you save this change, you will need to use the new address to access the admin panel — 192.168.225.1 will no longer work until you perform a factory reset.

What is the difference between 192.168.225.1 and more common gateways like 192.168.0.1?

Functionally, 192.168.225.1 works identically to more common gateways like 192.168.0.1 or 192.168.100.1 — it is simply a different address within the same private 192.168.x.x range. The key difference is that 192.168.225.1 is used by a narrower set of devices (primarily JioFi hotspots and a few other brands), whereas 192.168.0.1 and 192.168.1.1 are used by hundreds of router models worldwide. The 192.168.225.x subnet is less likely to conflict with other networks, which can be an advantage in environments where multiple routers are in use.