192.168.180.180 Admin Login

192.168.180.180 is a private Class C IPv4 address that belongs to the 192.168.180.0/24 subnet — an uncommon but fully valid range within the broader 192.168.0.0/16 private address space defined by RFC 1918. Unlike widely recognized default gateways such as 192.168.1.254 or 192.168.0.1, the address 192.168.180.180 is not the factory-assigned default gateway for any single major consumer router brand. Instead, it functions as a general-purpose private IP address that network administrators, IT professionals, and advanced users manually assign to routers, access points, servers, or other networked devices in custom-configured environments. Because the 192.168.180.x subnet is far less commonly used than the standard 192.168.1.x or 192.168.0.x ranges, choosing it for your network can actually improve security by reducing the risk of subnet overlap in VPN tunnels and remote access scenarios. Other commonly used private gateway addresses you may encounter include 192.168.10.1 and 192.168.8.1.

How to Access 192.168.180.180

If your router or network device has been configured to use 192.168.180.180 as its LAN IP address, you can access its admin panel by opening any web browser and typing http://192.168.180.180 directly into the address bar — then pressing Enter. This will load your device's web-based management interface, where you can configure wireless settings, security options, DHCP ranges, port forwarding rules, and firmware updates.

Before you attempt to log in, make sure your computer or device is connected to the same network — either via an Ethernet cable plugged into one of the router's LAN ports, or via the router's Wi-Fi network. If you are connected to a different network or subnet, your browser will not be able to reach 192.168.180.180. Once the login page loads, enter the administrator username and password. If you have not changed these credentials, check the label on the bottom or back of your device for the factory defaults. Common default combinations include admin / admin, admin / password, or a blank password field.

It is worth noting that because 192.168.180.180 is not a standard out-of-the-box default, someone — either you, a previous administrator, or an ISP technician — has deliberately set this address. If you are unsure whether 192.168.180.180 is actually your gateway, verify it first using the steps in the section below.

If You Cannot Access 192.168.180.180

If entering http://192.168.180.180 into your browser returns an error, a timeout, or a blank page, there are several possible explanations. The most common reason is that 192.168.180.180 is simply not the active gateway address for your current network. To confirm your actual default gateway, follow these steps:

• Windows: Open the Command Prompt (press Win + R, type cmd, and hit Enter). Then type ipconfig and press Enter. Look for the Default Gateway entry under your active network adapter.
• macOS: Open Terminal and type netstat -nr | grep default or go to System Settings > Network, select your active connection, and click Details to find the router IP.
• Linux: Open a terminal and run ip route | grep default. The IP address shown after via is your gateway.
• Android / iOS: Go to Settings > Wi-Fi, tap on your connected network, and look for the Gateway or Router field in the network details.

If your gateway is confirmed as 192.168.180.180 but you still cannot connect, try a different web browser, disable any VPN or proxy software, clear your browser cache, or use a direct Ethernet connection instead of Wi-Fi. Also check that no firewall rule on your computer is blocking local network access. If all else fails, you may need to perform a factory reset on your device to restore it to a known state — see the section below for guidance.

If your gateway is a different address entirely, check our guide to find your router IP address, or explore other common gateways such as 192.168.100.1 or 10.0.0.1.

Changing Your Router's Password at 192.168.180.180

If your network device is accessible at 192.168.180.180, one of the first things you should do — especially if this is a freshly configured or recently reset device — is change the default administrator password. Leaving a router on a non-standard IP like 192.168.180.180 with a default password is still a significant security risk, because anyone connected to your local network can attempt to log in.

To change your password, log in to the admin panel at http://192.168.180.180 using your current credentials. Once inside, navigate to the Administration, System, or Management section — the exact label depends on your device's firmware. Look for an option labeled Admin Password, Router Password, or Change Password. You will typically be asked to enter your current password, then type and confirm your new password twice.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Avoid using easily guessable information such as your address, name, or the IP address itself. Once saved, you will be prompted to log in again with your new credentials. Store the new password somewhere safe.

Router Username and Password List

What Kind of Devices Use 192.168.180.180?

Because 192.168.180.180 is not a standard factory-default IP for mainstream consumer routers, it is most commonly encountered in the following scenarios:

• Manually configured home or office routers: Network administrators who want to use a less predictable subnet — for added security or to avoid VPN conflicts — may manually set their router's LAN IP to 192.168.180.180. Any router that allows you to change its LAN IP address (which includes virtually all models from brands like Cisco, TP-Link, ASUS, Netgear, MikroTik, and Ubiquiti) can be configured to use this address.
• Enterprise and managed network equipment: In corporate environments, network engineers frequently assign IPs from non-standard subnets like 192.168.180.x to avoid overlap with other internal networks, especially when connecting multiple branch offices via VPN. Cisco routers and switches, Juniper devices, and Fortinet firewalls are all commonly configured with custom LAN IPs in this range.
• Industrial control systems: The 192.168.180.x subnet has a notable presence in industrial networking. GE's PACSystems RX3i and RSTi-EP programmable automation controllers (PACs) internally reserve the 192.168.180.x subnet for their embedded CPU communication interfaces, meaning this range may appear in factory automation and SCADA environments.
• Static device assignments: Even if your router's gateway is a different address, 192.168.180.180 could be statically assigned to a specific device on a 192.168.180.0/24 network — such as a NAS drive, IP camera, network printer, or managed switch — to give it a permanent, predictable address.
• Access points and repeaters in bridge mode: Wireless access points operating in bridge or repeater mode are often given static IPs like 192.168.180.180 so they can be managed independently from the main router without interfering with the DHCP pool.

Understanding the 192.168.180.0/24 Subnet

The address 192.168.180.180 sits within the 192.168.180.0/24 subnet, which provides 254 usable host addresses ranging from 192.168.180.1 to 192.168.180.254. The network address is 192.168.180.0 and the broadcast address is 192.168.180.255 — neither of which can be assigned to a device. With a standard subnet mask of 255.255.255.0, all devices within this range can communicate directly with each other without needing to pass through a router.

What makes the 192.168.180.x range particularly useful is its relative obscurity. The vast majority of home routers ship with default subnets of 192.168.1.x or 192.168.0.x. When you connect your home or office network to a corporate VPN, subnet conflicts are a common problem — your local 192.168.1.x network may clash with the remote network's 192.168.1.x range, causing routing failures. By using a less common subnet like 192.168.180.x, you significantly reduce the chance of this happening.

Here are some other IP addresses within the same 192.168.180.0/24 subnet that you might configure or encounter:

• 192.168.180.1 — The most natural choice for a gateway address in this subnet, often used as the router's LAN IP when the subnet is manually configured.
• 192.168.180.100 — A common starting point for DHCP pools in this range.
• 192.168.180.180 — The current address, sometimes chosen for its memorable, symmetrical pattern.
• 192.168.180.254 — The last usable host address in the subnet, sometimes used as an alternative gateway IP.

How to Perform a Factory Reset if You're Locked Out of 192.168.180.180

If you have forgotten the administrator password for the device at 192.168.180.180, or if the device is no longer responding to login attempts, a factory reset is your best option. A factory reset will erase all custom configurations — including the manually set IP address of 192.168.180.180 — and restore the device to its original out-of-the-box state, including the manufacturer's default IP address, username, and password.

The reset procedure varies slightly by device, but the most common method is:

1. Make sure the device is powered on and fully booted (wait at least 60 seconds after powering on).
2. Locate the Reset button on the device. It is usually a small recessed button on the back or bottom of the unit, labeled Reset or RST.
3. Using a straightened paperclip or a similar thin object, press and hold the Reset button for 10 to 30 seconds (the exact duration depends on the manufacturer — check your device's manual).
4. Release the button when the device's indicator lights flash or change pattern, signaling that the reset is in progress.
5. Wait for the device to fully reboot — this typically takes 1 to 3 minutes.
6. Once rebooted, the device will no longer be accessible at 192.168.180.180. Instead, use the manufacturer's default gateway IP (printed on the device label) to access the admin panel.

Important: A factory reset will delete your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and all other custom settings. Make sure you have noted down any important configuration details before proceeding. After the reset, you can reconfigure the device and, if desired, manually reassign 192.168.180.180 as the LAN IP address again.

Frequently Asked Questions About 192.168.180.180

Is 192.168.180.180 a valid IP address?

Yes, 192.168.180.180 is a fully valid private IPv4 address. It falls within the 192.168.0.0/16 private address block defined by RFC 1918, which means it can be freely used on any local area network (LAN) without registration or ISP approval. It is not routable on the public internet, so it will never conflict with any public website or server.

Which router brands use 192.168.180.180 as their default IP?

No major consumer router brand uses 192.168.180.180 as a factory-default gateway address. This IP is a general-purpose private address that must be manually assigned. However, any router that allows LAN IP customization — including models from Cisco, MikroTik, Ubiquiti, ASUS, TP-Link, and Netgear — can be configured to use 192.168.180.180 as its gateway. The 192.168.180.x subnet is also internally reserved by GE PACSystems industrial automation controllers.

How do I log in to 192.168.180.180?

Open a web browser and navigate to http://192.168.180.180. You must be connected to the same network as the device using this IP. Enter the administrator username and password when prompted. If you have not changed the credentials, check the sticker on your device for the factory defaults. If no login page appears, confirm that 192.168.180.180 is actually your device's IP using the ipconfig (Windows) or ip route (Linux/macOS) command.

Can two devices on my network share the IP 192.168.180.180?

No. Just like any IP address, 192.168.180.180 must be unique within your local network. If two devices are assigned the same IP address, an IP address conflict will occur, causing both devices to lose network connectivity intermittently or completely. Always ensure that each device on your 192.168.180.x network has a unique address. If you are using DHCP, your router will handle this automatically — but statically assigned addresses must be managed manually to avoid conflicts.

Why would someone choose 192.168.180.180 instead of a standard gateway like 192.168.1.1?

There are several good reasons. First, using a non-standard subnet like 192.168.180.x reduces the risk of IP conflicts when connecting to corporate VPNs, which often use the common 192.168.1.x range. Second, it adds a minor layer of security through obscurity — automated scripts and casual attackers typically target the most common default gateway addresses. Third, the symmetrical pattern of 192.168.180.180 makes it easy to remember once you have set it. For advanced users and network administrators, choosing a custom subnet is a standard best practice.

What is the subnet mask for 192.168.180.180?

The standard subnet mask for a Class C address like 192.168.180.180 is 255.255.255.0, which corresponds to a /24 prefix length. This gives you 254 usable host addresses in the range 192.168.180.1 through 192.168.180.254. The network address is 192.168.180.0 and the broadcast address is 192.168.180.255.