192.168.137.1 Admin Login

192.168.137.1 is a Class C private IPv4 address that serves as a default gateway in select router configurations and is most notably the fixed gateway IP automatically assigned by Microsoft Windows Internet Connection Sharing (ICS). Router brands including Cisco, Comtrend, and Tenda have been associated with this address in specific deployment scenarios. Because Windows ICS hard-codes the 192.168.137.0/24 subnet and assigns 192.168.137.1 to the host adapter sharing the connection, you will frequently encounter this IP on Windows 10 and Windows 11 machines acting as a software access point or wired internet bridge. Other commonly used private gateway addresses include 192.168.1.254 and 192.168.0.1.

How to Access 192.168.137.1

To reach the admin panel at 192.168.137.1, open your preferred web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.137.1 directly into the address bar (not the search box). Press Enter and the router or host device's login page should load within a few seconds.

Before you attempt to log in, make sure your computer or device is connected to the same network that uses 192.168.137.1 as its gateway. You can verify this on Windows by opening Command Prompt (search for cmd in the Start menu) and typing ipconfig. Look for the Default Gateway field — if it reads 192.168.137.1, you are on the correct network and the admin page should be reachable.

Once the login page appears, enter your router's default credentials. For most devices using this IP, the default username is admin and the default password is admin or password. Cisco devices may use cisco / cisco, while Comtrend units often default to root / 12345 or admin / admin. Always check the label on the underside of your router for the exact factory credentials specific to your model.

If You Can't Access 192.168.137.1

If typing http://192.168.137.1 into your browser produces an error or a blank page, work through the following checks before assuming the IP is wrong:

• Confirm your gateway: Run ipconfig in Command Prompt and verify that the Default Gateway is indeed 192.168.137.1. If it shows a different address, navigate to that IP instead. You can also check our guide to find your router IP address.
• Check your connection: Make sure your device is connected to the router via an Ethernet cable or Wi-Fi. A disconnected or loose cable is one of the most common reasons the admin page fails to load.
• Use the address bar, not the search bar: Many browsers will perform a web search if you type an IP into the search field. Always paste 192.168.137.1 into the address bar at the very top of the browser window.
• Disable VPN or proxy: Active VPN connections or proxy settings can reroute traffic away from your local network, making 192.168.137.1 unreachable. Temporarily disable any VPN before trying again.
• Windows ICS conflict: If your primary internet source also uses the 192.168.137.x range, Windows ICS will conflict with it. In this case, you may need to change the ICS subnet via the Windows Registry (ScopeAddress key under the SharedAccess service) or switch to a different internet-sharing method.
• Try a different browser or clear cache: Cached DNS or browser data can sometimes prevent the login page from loading. Try an incognito/private window or a different browser entirely.

192.168.137.1 and Windows Internet Connection Sharing (ICS)

One of the most distinctive features of 192.168.137.1 is its role as the fixed default gateway for Windows Internet Connection Sharing (ICS). When you enable ICS on a Windows PC — for example, to share a Wi-Fi connection over an Ethernet port to another device — Windows automatically assigns the static IP 192.168.137.1 to the sharing (private) network adapter. All client devices connected through that adapter receive addresses in the 192.168.137.0/24 range via DHCP, with 192.168.137.1 as their gateway and DNS server.

This behavior is consistent across Windows 7, 8, 10, and 11. Unlike most router settings, the ICS subnet is fixed and cannot be changed through the standard Windows GUI. If you need to alter it, you must edit the Windows Registry — specifically the ScopeAddress and ScopeAddressBackup keys under HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SharedAccess\Parameters — and then restart the ICS service. Always back up your registry before making such changes.

A common issue arises when your primary internet-providing network (e.g., your ISP's router) also uses the 192.168.137.x range. In that case, ICS will fail or cause instability. The solution is to either change the ICS subnet via the registry or ensure your main router uses a different subnet such as 192.168.1.x or 192.168.0.x.

Router Brands That Use 192.168.137.1

While 192.168.137.1 is less universally common than addresses like 192.168.0.1 or 10.0.0.1, several router manufacturers and platforms do use it as a default or assigned gateway:

• Cisco: Certain Cisco router and switch configurations — particularly in lab, enterprise, and inter-VLAN routing setups — use 192.168.137.1 as a configured default gateway. Cisco devices typically use the username cisco and password cisco by default, though this varies by model and firmware. Factory resetting a Cisco router involves using the config-register 0x2142 command in global configuration mode, followed by write erase and a reload.
• Comtrend: Some Comtrend DSL modem-routers have been documented using 192.168.137.1 in specific ISP-provisioned configurations. Comtrend's most common default credentials are root / 12345 or admin / admin. To factory reset a Comtrend device, locate the recessed Reset button on the back panel and hold it for 10–15 seconds with the unit powered on until the LEDs flash and the device reboots.
• Tenda: Certain Tenda router models — particularly those deployed in bridged or ICS-adjacent network environments — may present 192.168.137.1 as the gateway. Tenda's standard default login is admin / admin or no password at all on some older models. To reset a Tenda router, press and hold the WPS/RESET button for more than 10 seconds until the SYS LED switches from slow-flash to quick-flash, then release.
• Windows ICS Host: As described above, any Windows PC running Internet Connection Sharing will present itself as a gateway at 192.168.137.1. This is not a router brand per se, but it is the most common real-world source of this IP address on home and office networks.

Changing Your Router's Password at 192.168.137.1

Keeping the default admin password on any router is a significant security risk. If your device uses 192.168.137.1 as its gateway, you should change the admin password as soon as you complete the initial setup. Here's how to do it:

1. Open your browser and navigate to http://192.168.137.1.
2. Log in with your current credentials (check the router label if you haven't changed them yet).
3. Look for a section labeled Administration, System, Management, or Security — the exact name depends on your router's firmware.
4. Find the Change Password or Admin Password option and enter your new password twice to confirm.
5. Click Save or Apply and log back in with your new credentials.

Choose a strong password of at least 12 characters, mixing uppercase and lowercase letters, numbers, and symbols. Avoid using easily guessable information like your address or birthday. Once changed, store the password somewhere safe — unlike your Wi-Fi password, the router admin password cannot be recovered without a full factory reset.

Router Username and Password List

What Is 192.168.137.1 as a Private IP Address?

192.168.137.1 is a Class C private IPv4 address, falling within the reserved private range of 192.168.0.0 to 192.168.255.255 as defined by RFC 1918. This means it is not routable on the public internet — it exists solely within your local area network (LAN) and is invisible to the outside world.

When a router or Windows ICS host uses 192.168.137.1 as its gateway, every device that connects to that network receives a private IP address in the 192.168.137.0/24 subnet. For example:

• Your laptop might receive 192.168.137.2
• Your smartphone might receive 192.168.137.3
• Your tablet might receive 192.168.137.4

The subnet supports up to 254 usable host addresses (192.168.137.1 through 192.168.137.254), with 192.168.137.0 reserved as the network address and 192.168.137.255 as the broadcast address. The gateway at 192.168.137.1 acts as the traffic director — all requests from your devices pass through it on their way to the internet, and all incoming data is routed back to the correct device using Network Address Translation (NAT).

Because 192.168.137.1 is a private address, it is perfectly safe to use on any home or office network. However, only one device on the network should be assigned this address at any given time to avoid IP conflicts. If two devices share the same IP, both will experience connectivity problems.

Related IP Addresses in the 192.168.137.x Subnet

The 192.168.137.0/24 subnet contains a range of addresses that may be relevant depending on your network setup. While 192.168.137.1 is the most commonly used address in this range (typically assigned to the gateway), other addresses in the subnet are automatically distributed to connected client devices via DHCP. Here are some related IPs you may encounter:

• 192.168.137.2 – 192.168.137.100: Typically assigned to client devices (laptops, phones, tablets, smart TVs) by the DHCP server running on the 192.168.137.1 gateway.
• 192.168.137.100 – 192.168.137.200: Often used as the DHCP lease pool range in Windows ICS configurations.
• 192.168.137.254: Sometimes used as an alternate gateway address or reserved for network management in enterprise setups.
• 192.168.137.255: The broadcast address for this subnet — not assignable to any device.

If you are looking for other commonly used default gateway addresses outside this subnet, you may want to explore 192.168.0.1, 192.168.1.254, 192.168.8.1, 192.168.10.1, 192.168.100.1, or 10.0.0.1.

Frequently Asked Questions About 192.168.137.1

Why is my default gateway showing as 192.168.137.1?

If your device's default gateway is 192.168.137.1, it is most likely connected to a Windows PC that has Internet Connection Sharing (ICS) enabled. Windows automatically assigns 192.168.137.1 to the sharing adapter and distributes IPs in the 192.168.137.x range to connected clients. Alternatively, you may be connected to a Cisco, Comtrend, or Tenda router that has been configured to use this address.

How do I log into the admin panel at 192.168.137.1?

Open any web browser and type http://192.168.137.1 into the address bar. When the login page appears, enter your router's default credentials — commonly admin / admin for Tenda and Comtrend devices, or cisco / cisco for Cisco equipment. Check the label on the bottom of your router for the exact factory defaults.

Can I change the 192.168.137.1 IP address on my router?

Yes. Log into the admin panel at 192.168.137.1, navigate to LAN Settings (or equivalent), and change the IP to your preferred address. Note that if 192.168.137.1 is being used by Windows ICS, changing it requires editing the Windows Registry — there is no GUI option to do so.

What should I do if 192.168.137.1 is not working?

First, confirm that 192.168.137.1 is actually your gateway by running ipconfig in Command Prompt. If it is, check your cable connection, disable any VPN, and try a different browser. If the page still won't load, try pinging 192.168.137.1 from Command Prompt (ping 192.168.137.1) to test basic connectivity. A failed ping suggests a physical connection issue or a firewall blocking access.

Is 192.168.137.1 safe to use?

Yes. As a Class C private IP address, 192.168.137.1 is completely safe and is not accessible from the public internet. It operates only within your local network. However, you should always secure your router's admin panel with a strong, unique password to prevent unauthorized access from within your network.

How do I factory reset a router using 192.168.137.1?

The reset procedure depends on your router brand. For Tenda routers, hold the WPS/RESET button for more than 10 seconds until the SYS LED flashes rapidly. For Comtrend devices, press and hold the recessed Reset button on the back panel for 10–15 seconds. For Cisco routers, use the write erase command followed by reload in the CLI, or use the physical reset button if available. After any factory reset, the gateway will revert to 192.168.137.1 and you can log in again with the default credentials.