192.168.10.5 Admin Login

192.168.10.5 is a Class C private IPv4 address that belongs to the 192.168.10.0/24 subnet — a range actively used by several well-known router manufacturers as their default gateway network. Brands such as TRENDnet, Motorola, Wavlink, and Cudy all assign 192.168.10.1 as their default gateway, placing 192.168.10.5 squarely within their native subnet. This means that on any of these routers, 192.168.10.5 is a valid host address that can be assigned to a connected device — or manually configured as a static IP for a specific device on your network. Unlike the more common 192.168.1.254 or 192.168.0.1, the 192.168.10.x range is less frequently targeted by automated attacks, making it a slightly more secure default choice for home and small-office networks.

How to Access 192.168.10.5

To reach the admin panel at http://192.168.10.5, open any modern web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.10.5 directly into the address bar (not the search box). Press Enter and you should be taken to your router's login page. Make sure your device is connected to the same network as your router, either via Wi-Fi or a wired Ethernet cable plugged into one of the router's LAN ports.

On networks running TRENDnet routers such as the TEW-691GR or TEW-723BRM, the default gateway is 192.168.10.1, and 192.168.10.5 is a host address within that same subnet. Similarly, Motorola models like the WR850GP and WR850G use 192.168.10.1 as their default gateway, so 192.168.10.5 is a perfectly valid address on those networks. If you are trying to access the router's admin panel itself, you should navigate to 192.168.10.1 instead. However, if 192.168.10.5 has been manually assigned to a specific device — such as a NAS drive, IP camera, or network printer — then entering http://192.168.10.5 will take you directly to that device's management interface.

If You Can't Access 192.168.10.5

If typing http://192.168.10.5 into your browser returns an error or a blank page, work through the following checks before assuming the address is wrong:

• Confirm your network connection: Your device must be on the same 192.168.10.0/24 subnet. Open a command prompt (Windows: Start > cmd) and run ipconfig. Look for the Default Gateway value. If it shows 192.168.10.1, you are on the correct subnet and 192.168.10.5 should be reachable. If it shows a different gateway such as 192.168.1.1 or 192.168.0.1, your router does not use the 192.168.10.x range by default.
• Check for IP conflicts: Only one device can hold the address 192.168.10.5 at a time. If two devices share this address, neither will respond reliably. Log into your router at 192.168.10.1 and review the DHCP client list to spot any conflicts.
• Try a direct Ethernet connection: Wi-Fi interference can sometimes prevent access. Plug your computer directly into a LAN port on your TRENDnet, Motorola, Wavlink, or Cudy router using an Ethernet cable and try again.
• Disable browser extensions and VPNs: Ad blockers, proxy extensions, and active VPN connections can redirect or block local IP addresses. Temporarily disable them and retry.
• Ping the address: In the command prompt, run ping 192.168.10.5. If you receive replies, the device is online and the issue is browser-related. If the request times out, the device at 192.168.10.5 may be offline or the address may not be assigned.

If none of these steps resolve the issue, check our guide to find your router IP address to confirm your actual gateway.

Router Brands That Use the 192.168.10.x Subnet

The 192.168.10.0/24 subnet is the home network of several specific router manufacturers. Understanding which brands operate in this range helps you identify your hardware and apply the correct login credentials when working with 192.168.10.5.

• TRENDnet — Models including the TEW-691GR and TEW-723BRM ship with a default gateway of 192.168.10.1. The default username is admin and the default password is admin. TRENDnet's admin panel is accessed via https://192.168.10.1 (note the HTTPS). On these routers, 192.168.10.5 would typically be the fourth DHCP-assigned client address on the network.
• Motorola — The WR850GP and WR850G (v2, v3) use 192.168.10.1 as their default gateway. The default username is admin and the default password is motorola. The SSID also defaults to motorola followed by the last three digits of the MAC address. On a Motorola WR850-series network, 192.168.10.5 is a standard DHCP-assigned host address.
• Wavlink — Several Wavlink wireless routers and range extenders use 192.168.10.1 as their default management IP. The default credentials are typically admin / admin. Wavlink's interface is straightforward, with wireless settings, DHCP configuration, and firmware update options all accessible from the main dashboard.
• Cudy — Cudy routers also operate on the 192.168.10.0/24 subnet with a default gateway of 192.168.10.1. Default login credentials are admin / admin. Cudy's web interface features a setup wizard that guides you through initial configuration, making it beginner-friendly.

On all of the above networks, 192.168.10.5 is a host address within the subnet — the fifth usable address after the gateway. It may be dynamically assigned by DHCP to the fourth connected client device, or you can reserve it as a static IP for a specific device such as a printer, NAS, or IP camera.

Changing Your Router's Password on a 192.168.10.x Network

Keeping your router secured with a strong, unique password is one of the most important steps you can take to protect your home or office network. If your router uses the 192.168.10.x subnet — as TRENDnet, Motorola, Wavlink, and Cudy routers do — follow these steps to update your admin password:

1. Connect your device to the router's network via Wi-Fi or Ethernet.
2. Open your browser and navigate to http://192.168.10.1 (the default gateway for these brands).
3. Log in with your current credentials. If you have never changed them, use the factory defaults printed on the label on the bottom or back of your router.
4. Once inside the admin panel, locate the Administration, System, or Management section — the exact label varies by brand.
5. Find the Admin Password or Router Password field and enter your new password. Choose something at least 12 characters long, mixing uppercase letters, lowercase letters, numbers, and symbols.
6. Save your changes. You will be prompted to log in again with the new password.

On TRENDnet routers, the password change option is found under Administration > Management. On Motorola WR850-series routers, look under Basic Setup > Password. On Wavlink and Cudy devices, the option is typically under System > Admin Password. After changing your admin password, also update your Wi-Fi password under the Wireless settings section to ensure full network security.

Router Username and Password List

Factory Reset Procedures for 192.168.10.x Routers

If you have forgotten your admin credentials or your router at 192.168.10.5 is behaving unexpectedly, a factory reset will restore all settings — including the default gateway of 192.168.10.1 and the original username and password. Below are the reset procedures for the brands that use this subnet:

• TRENDnet (TEW-691GR, TEW-723BRM): Locate the small recessed reset button on the back of the router. With the router powered on, use a straightened paperclip or pin to press and hold the reset button for 10 seconds. Release when the LEDs flash. The router will reboot and return to factory defaults, with the gateway restored to 192.168.10.1 and credentials reset to admin / admin.
• Motorola (WR850GP, WR850G): With the router powered on, press and hold the reset button on the rear panel for 10 seconds until the power LED begins to flash. Release the button and wait for the router to fully reboot. The default gateway returns to 192.168.10.1, username to admin, and password to motorola. Alternatively, you can perform a 30-30-30 reset: hold the reset button for 30 seconds while powered on, then unplug the power while still holding for another 30 seconds, then plug back in and hold for a final 30 seconds.
• Wavlink: Press and hold the reset button (usually on the bottom or rear of the unit) for 10 seconds while the router is powered on. The indicator lights will flash to confirm the reset. After rebooting, the gateway returns to 192.168.10.1 and credentials reset to admin / admin.
• Cudy: With the router powered on, press and hold the reset button for 8–10 seconds until the system LED flashes rapidly. Release and allow the router to reboot. Factory defaults are restored, including the 192.168.10.1 gateway and admin / admin credentials.

Important: A factory reset erases all custom settings — your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and any other configurations you have made. Make sure to note down your current settings before performing a reset if you want to restore them afterward.

What Is 192.168.10.5 as a Private IP Address?

192.168.10.5 is a Class C private IPv4 address, defined under RFC 1918 as part of the reserved private address space. This means it is not routable on the public internet — it exists exclusively within your local network (LAN). No website, server, or external service will ever see 192.168.10.5 as your address; your router's public IP (assigned by your ISP) handles all external communication.

Within the 192.168.10.0/24 subnet, there are 254 usable host addresses ranging from 192.168.10.1 to 192.168.10.254. The address 192.168.10.1 is typically reserved for the router (gateway), and addresses like 192.168.10.5 are assigned to client devices — laptops, smartphones, smart TVs, printers, and more. Your router's DHCP server automatically hands out these addresses in sequence as devices connect to the network.

Here is an example of how address assignment works on a TRENDnet, Motorola, Wavlink, or Cudy network using the 192.168.10.x subnet:

• The router holds 192.168.10.1 (default gateway).
• The first connected device (e.g., your laptop) receives 192.168.10.2.
• The second connected device (e.g., your smartphone) receives 192.168.10.3.
• The third connected device (e.g., a tablet) receives 192.168.10.4.
• The fourth connected device (e.g., a smart TV) receives 192.168.10.5.

You can also manually assign 192.168.10.5 as a static IP to a specific device — such as a network printer or IP camera — so that it always has the same address on your network. This is useful for port forwarding rules and remote access configurations. To do this, log into your router at 192.168.10.1 and use the DHCP reservation feature, or configure the static IP directly on the device itself.

Related IP Addresses in the 192.168.10.x Subnet

The 192.168.10.0/24 subnet contains a number of addresses that serve specific roles on networks managed by TRENDnet, Motorola, Wavlink, and Cudy routers. Here are the most commonly referenced addresses in this range and how they relate to 192.168.10.5:

• 192.168.10.1 — The default gateway address for TRENDnet, Motorola, Wavlink, and Cudy routers. This is the address you type into your browser to access the router's admin panel.
• 192.168.10.2 – 192.168.10.4 — The first three DHCP-assigned client addresses on the network, typically given to the first devices that connect after the router boots.
• 192.168.10.5 — The current IP, typically the fourth DHCP-assigned client address, or a manually configured static IP for a specific device.
• 192.168.10.100 – 192.168.10.200 — Many routers configure their DHCP pool to start at .100, meaning 192.168.10.5 would need to be manually assigned as a static address outside the DHCP range to avoid conflicts.
• 192.168.10.254 — The last usable host address in the subnet, sometimes used as an alternative gateway address on certain network configurations.

If you are looking for other commonly used private gateway addresses outside the 192.168.10.x range, you may also want to explore 192.168.0.1, 192.168.8.1, 192.168.100.1, 10.0.0.1, and 192.168.1.254 — all of which are default gateways used by other major router brands.

Frequently Asked Questions About 192.168.10.5

Is 192.168.10.5 a router's default gateway?

Not directly. The default gateway for routers that use the 192.168.10.x subnet — such as TRENDnet, Motorola, Wavlink, and Cudy — is 192.168.10.1. The address 192.168.10.5 is a host address within the same subnet, typically assigned to a client device connected to one of these routers, or manually configured as a static IP.

How do I find out if 192.168.10.5 is my device's IP address?

On Windows, open the Command Prompt and type ipconfig. Look for the IPv4 Address field under your active network adapter. On a Mac, go to System Preferences > Network and select your active connection. On Android or iOS, go to Settings > Wi-Fi, tap your connected network, and look for the IP address field. If it shows 192.168.10.5, your device is on a TRENDnet, Motorola, Wavlink, or Cudy network.

What is the default username and password for routers on the 192.168.10.x network?

It depends on the brand. For TRENDnet routers (TEW-691GR, TEW-723BRM), the default is admin / admin. For Motorola WR850-series routers, it is admin / motorola. For Wavlink and Cudy, the default is typically admin / admin. Always check the label on the bottom or back of your specific router model for the exact factory credentials.

Can I assign 192.168.10.5 as a static IP to my printer or NAS?

Yes. On a network with a gateway of 192.168.10.1 (TRENDnet, Motorola, Wavlink, or Cudy), you can assign 192.168.10.5 as a static IP to any device. Log into your router at 192.168.10.1, navigate to the DHCP reservation or static IP section, and bind 192.168.10.5 to your device's MAC address. Alternatively, configure the static IP directly in the device's network settings using 192.168.10.5 as the IP, 255.255.255.0 as the subnet mask, and 192.168.10.1 as the default gateway.

Why does my browser show a security warning when I access 192.168.10.5?

Some routers and network devices use self-signed SSL certificates for their admin panels. When you access a local IP like 192.168.10.5 over HTTPS, your browser may warn you that the certificate is not trusted. This is normal for local network devices. You can safely proceed by clicking Advanced and then Proceed to 192.168.10.5. The connection is still encrypted — the warning simply means the certificate was not issued by a public certificate authority.

What other private IP addresses are related to 192.168.10.5?

The closest related addresses are others in the 192.168.10.0/24 subnet, particularly the gateway at 192.168.10.1. Other commonly used private gateways on different subnets include 192.168.0.1, 192.168.8.1, 192.168.100.1, 10.0.0.1, and 192.168.1.254.