192.168.10.4 Admin Login

The IP address 192.168.10.4 is a private Class C IPv4 address that sits within the 192.168.10.0/24 subnet. While it is not as universally recognized as 192.168.1.1 or 192.168.0.1, it plays a very specific and important role in certain industrial and networking environments. Most notably, SEW-EURODRIVE — a global manufacturer of drive technology and automation systems — hard-codes 192.168.10.4 as the factory-default IP address for the standard engineering interface of its MOVI-C® FIELD CONTROLLER (MFC1..) and MOVI-C® CONTROLLER (standard and advanced) devices. This makes 192.168.10.4 a critical address to know if you are commissioning, configuring, or troubleshooting any of these SEW-EURODRIVE automation controllers. Beyond industrial use, 192.168.10.4 also commonly appears as a DHCP-assigned host address in home and small-business networks where the gateway is set to 192.168.10.1, making it the fourth device to connect to such a network. Other well-known addresses in related subnets include 192.168.1.254 and 192.168.8.1.

How to Access 192.168.10.4

To reach the administration or engineering interface at 192.168.10.4, open your preferred web browser — such as Google Chrome, Mozilla Firefox, or Microsoft Edge — and type http://192.168.10.4 directly into the address bar. Do not type it into a search engine, as that will not connect you to the device. Press Enter and you should be presented with a login page.

Before you attempt to connect, make sure your computer is on the same subnet as 192.168.10.4. This means your PC or laptop must have an IP address in the range 192.168.10.1 – 192.168.10.254 (excluding 192.168.10.4 itself). If your machine is set to obtain an IP address automatically via DHCP and no DHCP server is present on the network, you will need to manually assign a static IP address — for example, 192.168.10.20 with a subnet mask of 255.255.255.0 — to your network adapter before you can reach 192.168.10.4.

For SEW-EURODRIVE MOVI-C® controllers, the engineering interface at 192.168.10.4 is accessed using the MOVISUITE® engineering software or directly via a web browser. The default subnet mask is 255.255.255.0 and the standard gateway is also set to 192.168.10.4 in the delivery state. Once connected, you can configure drive parameters, fieldbus settings, firmware updates, and diagnostic data.

If You Can't Access 192.168.10.4

If typing http://192.168.10.4 into your browser returns an error, a blank page, or a "site can't be reached" message, work through the following checks before assuming the address is wrong:

• Verify your subnet: Open the Command Prompt on Windows (Start > Run > type cmd, then press Enter) and run ipconfig /all. On Mac or Linux, open Terminal and type ifconfig. Look at your network adapter's IP address. If it does not start with 192.168.10., your computer is on a different subnet and cannot reach 192.168.10.4 without a manual IP change.
• Check your physical connection: For SEW-EURODRIVE MOVI-C® devices, you must connect your engineering PC directly to the controller's standard engineering interface port using an Ethernet cable. A wireless connection will not work unless your Wi-Fi router is already on the 192.168.10.0/24 subnet.
• Try a different browser: Some browser extensions, security plugins, or firewall rules can block access to local IP addresses. Try opening an incognito/private window or switching to a different browser entirely.
• Disable your PC firewall temporarily: Windows Defender Firewall or third-party antivirus software may block outbound connections to local network addresses. Temporarily disable it and retry.
• Confirm the device's current IP: If the device has been reconfigured, 192.168.10.4 may no longer be its active IP. Check your router's DHCP client list or use a network scanner tool to find the device's current address. If all else fails, perform a factory reset to restore the default IP of 192.168.10.4.

If 192.168.10.4 is not your gateway, you can find your correct router IP by running ipconfig /all on Windows and checking the Default Gateway field. You can also visit our guide to find your router IP address.

SEW-EURODRIVE and 192.168.10.4

SEW-EURODRIVE GmbH & Co KG is a German multinational company specializing in drive technology, gear units, motors, and industrial automation systems. Their MOVI-C® Modular Automation System is a comprehensive platform for motion control and automation, and several controllers within this system ship from the factory with 192.168.10.4 as their default engineering IP address.

The specific SEW-EURODRIVE devices that use 192.168.10.4 as their factory-default IP include:

• MOVI-C® FIELD CONTROLLER standard (MFC1..)
• MOVI-C® FIELD CONTROLLER advanced (MFC1..)
• MOVI-C® CONTROLLER standard
• MOVI-C® CONTROLLER advanced

On these devices, a DIP switch on the hardware can be used to toggle between the fixed factory IP of 192.168.10.4 and a user-defined IP address stored on the device's memory card. This gives engineers flexibility during commissioning — you can use the known default address of 192.168.10.4 for initial setup, then switch to a custom IP that fits your plant network's addressing scheme.

It is important to note that the IP address 192.168.10.4 is not retained when the delivery state is restored on these SEW-EURODRIVE controllers. After a factory reset, the device reverts to 192.168.10.4 only if the DIP switch is set to the fixed-IP position. Always consult the operating instructions for your specific MOVI-C® model before performing a reset in a live production environment.

Beyond SEW-EURODRIVE, 192.168.10.4 also appears in networks built around Cisco small business devices — such as the ESW 500 Series managed switches — where the 192.168.10.0/24 subnet is commonly used and 192.168.10.4 may be assigned to a host device via DHCP or static configuration.

Changing Your Password at 192.168.10.4

Whether you are accessing a SEW-EURODRIVE MOVI-C® controller or a network router at 192.168.10.4, leaving the device on its default credentials is a serious security risk. Anyone connected to the same 192.168.10.0/24 network could log in and alter your configuration. You should change your password as soon as you complete the initial setup.

To change your password after logging in to 192.168.10.4:

1. Log in to the web-based interface at http://192.168.10.4 using your current credentials.
2. Navigate to the Administration, System, or Security section of the interface — the exact location depends on your device's firmware.
3. Look for a Change Password or User Management option.
4. Enter your current password, then type your new password twice to confirm it.
5. Click Save or Apply to commit the change.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and special characters. Avoid using easily guessable information such as your name, address, or the device's IP address (192.168.10.4) as part of the password. Store your new password in a secure password manager so you do not lose access to the device.

Router Username and Password List

Factory Reset for Devices at 192.168.10.4

If you have forgotten your login credentials for the device at 192.168.10.4, or if the interface is no longer responding correctly, a factory reset will restore the device to its default settings — including the default IP address of 192.168.10.4 (where applicable) and the original username and password.

For SEW-EURODRIVE MOVI-C® Controllers:

1. Power down the MOVI-C® controller safely, following all electrical safety procedures for your installation.
2. Locate the DIP switch on the controller hardware and set it to the fixed-IP position to ensure the device returns to 192.168.10.4 after the reset.
3. Initiate the delivery-state restore procedure as described in the operating instructions for your specific MOVI-C® model (MFC1.. or MOVI-C® CONTROLLER standard/advanced). This typically involves a specific button sequence or a software command via MOVISUITE®.
4. Power the device back on and wait for it to fully boot.
5. Set your engineering PC's IP address to a static address in the 192.168.10.0/24 range — for example, 192.168.10.20 with subnet mask 255.255.255.0.
6. Open your browser and navigate to http://192.168.10.4 to access the engineering interface with the default credentials.

For general routers and network devices on the 192.168.10.0/24 subnet:

1. Locate the Reset button on the back or bottom of your router or network device.
2. With the device powered on, use a pin or paperclip to press and hold the Reset button for 10–30 seconds until the indicator lights flash or change pattern.
3. Release the button and allow the device to reboot — this typically takes 60–90 seconds.
4. Once rebooted, the device will return to its factory default settings. Check the label on the device for the default IP address, username, and password.

Important: A factory reset will erase all custom configurations, including your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and any other settings you have applied. Make sure to back up your configuration before performing a reset if your device supports it.

What Is 192.168.10.4? Understanding Private IP Addresses

192.168.10.4 is a private IPv4 address belonging to the Class C range defined by RFC 1918. Private IP addresses like 192.168.10.4 are reserved exclusively for use within local area networks (LANs) and are not routable on the public internet. This means that no data packet carrying 192.168.10.4 as its destination address will ever travel across the open internet — it stays entirely within your local network.

The 192.168.10.0/24 subnet — which includes all addresses from 192.168.10.0 to 192.168.10.255 — provides up to 254 usable host addresses (192.168.10.1 through 192.168.10.254). The address 192.168.10.0 is the network identifier and 192.168.10.255 is the broadcast address; neither can be assigned to a device. Within this range, 192.168.10.4 is the fourth usable host address.

In a typical home or small-business network running on the 192.168.10.0/24 subnet, the router or gateway is usually assigned 192.168.10.1. When devices connect to the network and request an IP address via DHCP, the router assigns them addresses sequentially — so the first device might get 192.168.10.2, the second 192.168.10.3, and the third device would receive 192.168.10.4. This is the most common way 192.168.10.4 appears in everyday home networking.

Because 192.168.10.4 is a private address, every home or office network in the world is free to use it simultaneously without any conflict — conflicts only arise within the same local network if two devices are assigned the same IP. To avoid this, always ensure that only one device on your network holds the address 192.168.10.4 at any given time, whether through DHCP management or careful static IP assignment.

192.168.10.4 and the 192.168.10.0/24 Subnet

The 192.168.10.0/24 subnet is a popular choice for enterprise VLAN segmentation, small-business networks, and industrial automation environments. Unlike the more crowded 192.168.1.x and 192.168.0.x ranges — which are the default for the vast majority of consumer routers — the 192.168.10.x range is often deliberately chosen by network administrators who want to avoid IP conflicts when connecting to client VPNs or remote networks that may already use the common ranges.

Within the 192.168.10.0/24 subnet, several specific IP addresses have well-known device associations:

• 192.168.10.1 — The most common default gateway for routers and access points on this subnet, used by brands including Netgear, D-Link, TP-Link, Asus, Cisco, Linksys, Tenda, and Huawei in certain configurations.
• 192.168.10.2 — Used by Cisco ESW 500 Series managed switches (ESW-520 and ESW-540 families) as a static fallback IP when DHCP is unavailable.
• 192.168.10.4 — Factory-default engineering IP for SEW-EURODRIVE MOVI-C® FIELD CONTROLLER and MOVI-C® CONTROLLER devices.
• 192.168.10.10 — Default IP for the Cisco AP541N Small Business Pro access point and the TRENDnet TS-S402 NAS device.
• 192.168.10.254 — An alternative default gateway address used by some ISP-provided modems and routers on this subnet.

Understanding where 192.168.10.4 fits within this subnet helps you plan your network addressing to avoid conflicts, especially in mixed environments where consumer routers, Cisco small business switches, and SEW-EURODRIVE industrial controllers may all coexist on the same physical network infrastructure.

Frequently Asked Questions About 192.168.10.4

What device uses 192.168.10.4 as its default IP address?

The most notable devices that ship with 192.168.10.4 as their factory-default IP address are the SEW-EURODRIVE MOVI-C® FIELD CONTROLLER (MFC1.. standard and advanced) and the MOVI-C® CONTROLLER (standard and advanced). These are industrial automation controllers used in drive technology and motion control applications. In home and small-business networks, 192.168.10.4 is also commonly assigned by a DHCP server as the fourth host address on a 192.168.10.0/24 subnet.

How do I log in to 192.168.10.4?

Open your web browser and type http://192.168.10.4 into the address bar and press Enter. Make sure your computer is on the same 192.168.10.0/24 subnet — if not, manually assign your PC a static IP such as 192.168.10.20 with subnet mask 255.255.255.0. For SEW-EURODRIVE MOVI-C® devices, use the MOVISUITE® engineering software or a direct browser connection. Default credentials vary by device — check the label on your hardware or its documentation.

Why can't I access 192.168.10.4 in my browser?

The most common reason you cannot reach 192.168.10.4 is that your computer is on a different subnet. Run ipconfig /all (Windows) or ifconfig (Mac/Linux) and check your IP address. If it does not start with 192.168.10., you need to either connect to the correct network or manually set a static IP in the 192.168.10.x range. Also check that you are using a direct Ethernet connection for industrial devices like SEW-EURODRIVE controllers, and that no firewall is blocking local network access.

Is 192.168.10.4 the same as a router's default gateway?

Not always. In most home networks, the default gateway on the 192.168.10.0/24 subnet is 192.168.10.1, not 192.168.10.4. However, for SEW-EURODRIVE MOVI-C® controllers, the device ships with both its IP address and its standard gateway set to 192.168.10.4 in the delivery state. In a general home network, 192.168.10.4 is typically a host address assigned to a connected device, not the gateway itself.

What is the default username and password for 192.168.10.4?

The default credentials depend entirely on the device you are accessing at 192.168.10.4. For SEW-EURODRIVE MOVI-C® controllers, refer to the MOVISUITE® documentation and the device's operating instructions for the correct engineering access credentials. For general routers and network devices on the 192.168.10.0/24 subnet, the most common defaults are admin / admin, admin / password, or admin / (blank). Always check the sticker on the back or bottom of your device for the exact factory credentials.

How do I reset a device at 192.168.10.4 to factory defaults?

For SEW-EURODRIVE MOVI-C® controllers, use the DIP switch to set the fixed-IP mode and follow the delivery-state restore procedure in the device's operating instructions — note that the IP address 192.168.10.4 is not retained after a restore unless the DIP switch is in the fixed-IP position. For standard routers and network devices, press and hold the physical Reset button on the device for 10–30 seconds while it is powered on, then release and allow it to reboot. This will restore all factory defaults including the IP address and login credentials.

What other IP addresses are related to 192.168.10.4?

Since 192.168.10.4 belongs to the 192.168.10.0/24 subnet, closely related addresses include 192.168.10.1 (the typical default gateway), 192.168.10.2 (Cisco ESW 500 Series switch fallback IP), and 192.168.10.10 (Cisco AP541N and TRENDnet TS-S402 default IP). Other commonly used private IPs in adjacent subnets include 192.168.1.254, 192.168.8.1, and 192.168.10.1.