192.168.1.30 Admin Login

192.168.1.30 is a Class C private IPv4 address that sits within the widely used 192.168.1.0/24 subnet. While it is not the most common default gateway address (that distinction belongs to 192.168.1.1 or 192.168.1.254), 192.168.1.30 is a legitimate and well-documented default IP address used by specific networking and surveillance hardware. Most notably, Messoa Technologies IP cameras — including models such as the NCB855PRO and the LPR610 — ship with 192.168.1.30 as their factory-set static IP address. Additionally, a wide range of TRENDnet networking devices (switches, access points, and routers) operate within the 192.168.1.x subnet and may resolve to 192.168.1.30 depending on DHCP assignment or manual configuration. Because 192.168.1.30 is a private IP, it cannot be routed over the public internet — it exists exclusively within your local area network (LAN) and is governed by RFC 1918.

If your device is using 192.168.1.30, you can access its admin panel by typing http://192.168.1.30 directly into your browser's address bar. Other commonly used default gateways in the same subnet include 192.168.1.1 and 192.168.1.254. If you are unsure which IP your router or device uses, check the label on the bottom or back of the device, or consult our guide to finding your router's IP address.

How to Access 192.168.1.30

Accessing the admin panel at 192.168.1.30 is straightforward, but you must be connected to the same local network as the device using this address. Follow these steps:

1. Connect your device — Use a wired Ethernet cable for the most reliable connection, or connect via Wi-Fi to the same network. For Messoa IP cameras, a direct Ethernet connection to your PC or through a switch is recommended.
2. Open your web browser — Chrome, Firefox, Edge, or Safari all work. In the address bar, type http://192.168.1.30 and press Enter. Do not use a search engine — type it directly into the address bar.
3. Enter your credentials — For Messoa cameras, the default username is admin and the default password is either 1234 or the model number of the camera (e.g., NCB855PRO). For TRENDnet devices, the default is typically admin / admin. Always check the label on the back or bottom of your device for the exact credentials.
4. Navigate the admin panel — Once logged in, you can configure network settings, change the device IP, update firmware, manage security settings, and more.

Because 192.168.1.30 is a private IP address, only devices on the same local network can reach it. If you are trying to access it remotely over the internet, you will need to set up port forwarding or a VPN on your router first.

If You Can't Access 192.168.1.30

If typing http://192.168.1.30 into your browser returns an error, a blank page, or a "site can't be reached" message, work through the following troubleshooting steps:

• Verify your gateway address: Open the Command Prompt (Windows: press Win + R, type cmd, press Enter, then type ipconfig /all) or Terminal (Mac/Linux: type ip route or netstat -nr). Look for the Default Gateway value. If it shows something other than 192.168.1.30 — such as 192.168.1.1 or 192.168.1.254 — then your router uses a different address. Visit our router IP finder guide for more help.
• Check your network connection: Make sure your computer or device is actually connected to the same network as the device at 192.168.1.30. A disconnected or wrong Wi-Fi network is a common cause of access failures.
• Try HTTPS: Some devices, especially newer Messoa IP cameras, may require a secure connection. Try https://192.168.1.30 instead.
• Disable browser extensions: Ad blockers or VPN extensions can sometimes interfere with local IP access. Try opening an incognito/private window or temporarily disabling extensions.
• Check for IP conflicts: If another device on your network has been manually assigned 192.168.1.30, there will be a conflict. Log into your router's DHCP table (usually at 192.168.1.1) and check for duplicate assignments.
• Ping the address: Open Command Prompt and type ping 192.168.1.30. If you receive replies, the device is online and reachable — the issue may be browser-related. If the ping times out, the device may be offline, powered down, or on a different subnet.

Router Brands and Devices That Use 192.168.1.30

Unlike the most common default gateway addresses, 192.168.1.30 is associated with a more specific set of hardware. Here is what our research confirms:

Messoa Technologies

Messoa Technologies is the most clearly documented brand that uses 192.168.1.30 as a factory-default static IP address. Multiple Messoa IP camera models — including the NCB855PRO 2-Megapixel Box IP Camera and the LPR610 2-Megapixel IR Bullet LPR/ANPR Network Camera — are pre-configured with this address out of the box. When you first connect a Messoa camera to your network, you must configure your PC's IP address to be in the same subnet (e.g., 192.168.1.X, where X is between 2 and 254, but not 30) before you can access the camera's web interface at http://192.168.1.30. Default login credentials for Messoa cameras are typically admin for the username and 1234 or the camera's model number as the password.

TRENDnet

TRENDnet produces a broad range of networking equipment — including routers, switches, access points, and IP cameras — many of which operate within the 192.168.1.x address space. While TRENDnet's primary default gateway is typically 192.168.1.1, numerous TRENDnet models (such as the TEW-series routers and TEG-series switches) can assign or be manually configured to use 192.168.1.30. TRENDnet's TV-IP series of network cameras also operate in this subnet. Default credentials for most TRENDnet devices are admin / admin.

General-Purpose DHCP Assignment

Beyond specific brands, 192.168.1.30 is also commonly assigned as a dynamic DHCP address by any router operating in the 192.168.1.0/24 subnet. If your router's DHCP pool starts at 192.168.1.2 or 192.168.1.10, the 30th or so device to connect may receive 192.168.1.30 automatically. This means the address could belong to a laptop, smartphone, smart TV, printer, or any other networked device — not necessarily a router or camera.

Changing Your Password at 192.168.1.30

Whether you are managing a Messoa IP camera or a TRENDnet device at 192.168.1.30, changing the default password is one of the most important security steps you can take. Default credentials are publicly documented and leave your device vulnerable to unauthorized access. Here is how to update your password:

1. Log in to the admin panel at http://192.168.1.30 using your current credentials.
2. Navigate to the Administration, System, or Security section — the exact label depends on your device's firmware.
3. Look for a Password, Change Password, or User Management option.
4. Enter your current password, then type your new password twice to confirm. Choose a strong password that is at least 12 characters long and includes a mix of letters, numbers, and symbols.
5. Click Save or Apply to confirm the change. You will be prompted to log in again with your new credentials.

For Messoa cameras specifically, you can also change the admin password under the Administration > User tab in the web interface. It is also strongly recommended to change the default IP address from 192.168.1.30 to something less predictable once your device is on a secured network.

Router Username and Password List

How to Factory Reset a Device at 192.168.1.30

If you have forgotten the admin password for your device at 192.168.1.30, or if the device is behaving unexpectedly, a factory reset will restore all settings — including the IP address — back to their defaults. Warning: A factory reset will erase all custom configurations, including your Wi-Fi name, password, port forwarding rules, and any other changes you have made.

For Messoa IP Cameras

1. If you can still access the web interface at http://192.168.1.30, go to Administration or System and click Restore to Factory Default.
2. If you cannot access the interface, locate the physical Reset button on the camera body (usually a small pinhole button).
3. With the camera powered on, use a straightened paperclip or pin to press and hold the Reset button for 10–15 seconds until the status LED blinks or the camera restarts.
4. After the reset, the camera's IP address will return to 192.168.1.30, and the default credentials will be restored (admin / 1234 or model number).

For TRENDnet Devices

1. Locate the Reset button on the back or bottom of your TRENDnet device.
2. With the device powered on, press and hold the Reset button using a pin or paperclip for 10–15 seconds.
3. Release the button when the power LED begins to flash. The device will reboot automatically.
4. Once rebooted, access the admin panel using the default IP (check your device label) and default credentials (admin / admin for most TRENDnet models).

After any factory reset, it is critical to immediately change the default password and reconfigure your network settings to restore security.

What Is a Private IP Address Like 192.168.1.30?

192.168.1.30 is a Class C private IPv4 address, as defined by the Internet Assigned Numbers Authority (IANA) under RFC 1918. This means it is reserved exclusively for use within private local area networks (LANs) and can never be routed over the public internet. Every home, office, or enterprise network that uses the 192.168.1.x range has its own isolated pool of these addresses — so 192.168.1.30 on your network is completely separate from 192.168.1.30 on your neighbor's network.

Here is how private addressing works in practice on a typical 192.168.1.x network:

• Your router typically holds the gateway address — most commonly 192.168.1.1 or 192.168.1.254.
• Your laptop might be assigned 192.168.1.2 by DHCP.
• Your smartphone might receive 192.168.1.3.
• A network printer might be statically set to 192.168.1.10.
• A Messoa IP camera ships with a static address of 192.168.1.30.

The router uses Network Address Translation (NAT) to map all of these private addresses to a single public IP address when communicating with the internet. This is why multiple devices can share one internet connection simultaneously.

The full usable address range of the 192.168.1.0/24 subnet is 192.168.1.1 through 192.168.1.254, giving you up to 254 unique device addresses. The address 192.168.1.0 is the network identifier and 192.168.1.255 is the broadcast address — neither can be assigned to a device. With 192.168.1.30 sitting near the lower end of this range, it is a common target for static assignment to infrastructure devices like cameras, printers, and managed switches.

Related IP Addresses in the 192.168.1.x Subnet

The 192.168.1.0/24 subnet is one of the most widely used private network ranges in the world. If 192.168.1.30 is not the correct address for your device, one of the following commonly used addresses in the same subnet may be what you are looking for:

• 192.168.1.1 — The most common default gateway for routers from TP-Link, ASUS, Netgear, Linksys, and many others.
• 192.168.1.254 — Used by many DSL modems and routers from brands like 2Wire, Westell, and some TRENDnet models.
• 192.168.1.2 — Often the first DHCP-assigned address in a 192.168.1.x network.
• 192.168.1.100 — A common static IP for network printers and managed switches.

If your device is not in the 192.168.1.x range at all, you may want to check these other common default gateways:

• 192.168.0.1 — Default for many Netgear, D-Link, and some TP-Link routers.
• 10.0.0.1 — Used by Xfinity/Comcast gateways and some Apple routers.
• 192.168.2.1 — Default for some Belkin and SMC routers.
• 192.168.8.1 — Default for Huawei mobile Wi-Fi routers and some ZTE devices.
• 192.168.100.1 — Used by some cable modems and ISP-provided gateways.
• 192.168.10.1 — Used by some Cisco and Ubiquiti devices.

Frequently Asked Questions About 192.168.1.30

What devices use 192.168.1.30 as their default IP?

The most well-documented devices that use 192.168.1.30 as a factory-default static IP are Messoa Technologies IP cameras, including the NCB855PRO and LPR610 models. TRENDnet networking equipment also commonly operates in the 192.168.1.x range and may use 192.168.1.30 through DHCP assignment or manual configuration. If you are unsure, check the label on the back or bottom of your device.

What is the default username and password for 192.168.1.30?

For Messoa IP cameras at 192.168.1.30, the default username is admin and the default password is 1234 or the camera's model number. For TRENDnet devices, the default is typically admin / admin. Always verify by checking the sticker on your specific device, as credentials can vary by model.

Why can't I access 192.168.1.30 in my browser?

The most common reasons are: (1) your computer is not on the same 192.168.1.x network as the device, (2) the device's IP has been changed from the default 192.168.1.30, (3) there is an IP address conflict with another device, or (4) the device is powered off or disconnected. Run ipconfig /all on Windows or ip route on Mac/Linux to verify your network settings.

Is 192.168.1.30 safe to use on my network?

Yes — 192.168.1.30 is a standard private IP address and is completely safe to use within your local network. However, if a device at this address is using default credentials (like admin/1234), you should change the password immediately to prevent unauthorized access from other devices on your LAN.

Can two devices share the IP address 192.168.1.30?

No. Within a single network, every device must have a unique IP address. If two devices are both assigned 192.168.1.30 — whether statically or via DHCP — an IP address conflict will occur, causing connectivity problems for both devices. If you have a Messoa camera with a static IP of 192.168.1.30, make sure your router's DHCP pool excludes that address to prevent conflicts.

How do I change the IP address of my device from 192.168.1.30 to something else?

Log in to the admin panel at http://192.168.1.30, navigate to the Network or LAN Settings section, and enter a new static IP address within your subnet (e.g., 192.168.1.50). Save your changes. Note that after changing the IP, you will need to use the new address to access the admin panel — 192.168.1.30 will no longer work.