192.168.1.240 Admin Login

Amped Wireless routers and range extenders are the primary devices that use 192.168.1.240 as their default gateway IP address. Models such as the SR20000G, R20000G, RE1300M, and AV3000 all ship with 192.168.1.240 as their factory-set admin login address. This makes 192.168.1.240 a notably specific IP — unlike the more widespread 192.168.1.1 or 192.168.0.1, it is closely associated with the Amped Wireless product line. If you own an Amped Wireless device, typing http://192.168.1.240 into your browser is your primary route into the router's web-based administration panel. Alternatively, Amped Wireless also supports access via the local hostname http://setup.ampedwireless.com, though the IP address method is more reliable when hostname resolution fails.

192.168.1.240 is a Class C private IPv4 address, falling within the 192.168.0.0/16 reserved block defined by RFC 1918. It belongs to the 192.168.1.0/24 subnet, which supports up to 254 usable host addresses (192.168.1.1 through 192.168.1.254). Because it sits near the high end of this range (host number 240), it is deliberately chosen by Amped Wireless to avoid conflicts with the DHCP pools that most routers assign dynamically — typically starting from 192.168.1.2 or 192.168.1.100 upward. Other commonly used IPs in this same subnet include 192.168.1.254 and the well-known 192.168.1.1.

How to Access 192.168.1.240

To access your Amped Wireless router or range extender's admin panel at 192.168.1.240, follow these steps:

1. Connect your device — Use an Ethernet cable plugged into one of the router's LAN ports for the most stable connection. You can also connect over Wi-Fi, but a wired connection is recommended for initial setup and configuration changes.
2. Open your web browser — Launch any modern browser (Chrome, Firefox, Edge, or Safari) and type http://192.168.1.240 directly into the address bar. Do not use the search bar — make sure you're typing into the URL/address field.
3. Reach the login page — You should see the Amped Wireless web menu login screen. If the page does not load, try http://setup.ampedwireless.com as an alternative. If neither works, see the troubleshooting section below.
4. Enter your credentials — The default username and password for most Amped Wireless devices are both left blank (no entry required). On some models, the credentials may be admin / admin. Check the label on the bottom or back of your device for the exact defaults.
5. Navigate the dashboard — Once logged in, you'll have access to wireless settings, DHCP configuration, firmware updates, security options, and more through the Amped Wireless web interface.

Because 192.168.1.240 is a private IP address, it is only reachable from within your local network. You cannot access it from the internet or from a device that is not connected to the same router.

If You Can't Access 192.168.1.240

If entering http://192.168.1.240 in your browser doesn't bring up the Amped Wireless login page, there are several possible causes and fixes:

• Verify your gateway address: 192.168.1.240 may not be your current default gateway. Open a Command Prompt (Windows: press Win + R, type cmd, press Enter) and run ipconfig /all. Look for the Default Gateway field. On macOS or Linux, run netstat -nr or ip route. If the gateway shown is different from 192.168.1.240, use that address instead, or check our guide to find your router IP address.
• Check your connection: Make sure your device is actually connected to the Amped Wireless network — either via Ethernet cable or Wi-Fi. If you're connected to a different network, you won't be able to reach 192.168.1.240.
• Try the hostname alternative: Amped Wireless devices also respond to http://setup.ampedwireless.com. Try this URL if the IP address method fails.
• Clear your browser cache: Sometimes cached data can interfere. Try opening an incognito/private window and entering http://192.168.1.240 again.
• Disable VPN or proxy: If you're running a VPN or proxy service, it may be routing your traffic away from the local network. Disable it temporarily and try again.
• The IP may have been changed: A previous administrator may have changed the default gateway from 192.168.1.240 to something else. If you don't know the new IP, you'll need to perform a factory reset to restore 192.168.1.240 as the default.

Amped Wireless Factory Reset — Restoring 192.168.1.240

If you've forgotten your admin password or the gateway IP has been changed from 192.168.1.240, a factory reset will restore all settings to their defaults, including the login IP address. Here's how to do it on Amped Wireless devices:

Method 1: Hardware Reset Button

1. Make sure your Amped Wireless router or range extender is powered on.
2. Locate the Reset button on the back or bottom panel of the device. It is typically a small recessed button labeled "Reset."
3. Use a straightened paperclip, pin, or similar thin object to press and hold the Reset button for 5–10 seconds.
4. Release the button when the device's LEDs begin to flash or the unit restarts. This indicates the reset is in progress.
5. Wait for the device to fully reboot (approximately 60–90 seconds). Once it restarts, all settings — including the admin IP — will be restored to factory defaults, and 192.168.1.240 will be accessible again.

Method 2: Software Reset via Admin Panel

1. Log in to your Amped Wireless admin panel at http://192.168.1.240.
2. Navigate to More Settings > Management > Save/Reload Settings.
3. Click the Reset Settings to Default button.
4. Confirm the action and wait for the device to reboot.

Important: A factory reset will erase all custom configurations, including your Wi-Fi name (SSID), password, port forwarding rules, and any other changes you've made. Make sure to back up your settings before resetting if possible.

Changing Your Password on an Amped Wireless Device at 192.168.1.240

Securing your Amped Wireless router's admin panel is critical. The default credentials (often blank or admin/admin) are publicly known, and leaving them unchanged puts your network at risk. To change your admin password:

1. Log in to the admin panel at http://192.168.1.240 using your current credentials.
2. Navigate to the Management or Administration section within the web interface.
3. Look for the Admin Password or Change Password option.
4. Enter your new password twice to confirm it, then save the changes.
5. You will be prompted to log in again with your new password.

Choose a strong password that combines uppercase and lowercase letters, numbers, and special characters. Avoid using easily guessable information like your address or birthday. Once you've secured the admin panel at 192.168.1.240, also make sure your Wi-Fi network password (under the Wireless Settings section) is equally strong.

Router Username and Password List

What Is 192.168.1.240 and Why Does Amped Wireless Use It?

192.168.1.240 is a private Class C IPv4 address that exists within the 192.168.1.0/24 subnet. It is not routable on the public internet — it is exclusively used within local area networks (LANs), such as your home or office Wi-Fi. The Internet Assigned Numbers Authority (IANA) has reserved the entire 192.168.0.0/16 block for private use, meaning no public website or server will ever have this address.

Amped Wireless deliberately chose 192.168.1.240 as the default gateway for many of its routers and range extenders — including the SR20000G, R20000G, RE1300M, and AV3000 — to minimize the chance of IP conflicts. Most home routers assign DHCP addresses starting from the lower end of the 192.168.1.x range (e.g., 192.168.1.2 through 192.168.1.150). By placing the admin gateway at 192.168.1.240, Amped Wireless ensures the router's own management IP stays well clear of the dynamic pool.

When you connect a device to your Amped Wireless network, it receives a private IP address from the router's DHCP server — for example:

• Your laptop might receive 192.168.1.100
• Your smartphone might receive 192.168.1.101
• Your smart TV might receive 192.168.1.102

All of these devices communicate with the internet through the router at 192.168.1.240, which acts as the gateway — forwarding requests outward and routing responses back to the correct device. The router itself also has a separate public IP address assigned by your Internet Service Provider (ISP), which is the address the rest of the internet sees.

Other commonly used private IPs in the same 192.168.1.x subnet include 192.168.1.1 (used by Linksys, ASUS, TP-Link, and others) and 192.168.1.254 (used by some DSL modems and ISP-provided gateways). If you're looking for a different subnet entirely, 192.168.0.1 and 10.0.0.1 are also widely used private gateway addresses.

Frequently Asked Questions About 192.168.1.240

Which router brands use 192.168.1.240 as their default gateway?

Amped Wireless is the primary brand associated with 192.168.1.240 as a default gateway. Specific models include the SR20000G Dual Band Range Extender, the R20000G High Power Router, the RE1300M, and the AV3000 Powerline series. If your device is an Amped Wireless product and you're trying to access its settings, 192.168.1.240 is your go-to admin address. You can also try the branded URL http://setup.ampedwireless.com as an alternative entry point.

What is the default username and password for 192.168.1.240?

For most Amped Wireless devices that use 192.168.1.240, the default login credentials are blank for both username and password — simply leave both fields empty and click Login. On some models, you may need to try admin / admin or admin / password. Always check the label on the bottom or back of your specific Amped Wireless device for the exact factory defaults, as they can vary by model.

Why can't I reach 192.168.1.240 in my browser?

If 192.168.1.240 isn't loading, first confirm that your device is connected to the Amped Wireless network. Then open a command prompt and run ipconfig /all (Windows) to verify that 192.168.1.240 is listed as your Default Gateway. If it's not, your router may have had its IP changed — try performing a factory reset by holding the Reset button on your Amped Wireless device for 5–10 seconds to restore 192.168.1.240 as the default.

Is 192.168.1.240 safe to use?

Yes — 192.168.1.240 is a private IP address and is completely safe. It cannot be accessed from outside your local network, so it is not exposed to the public internet. However, you should still protect your Amped Wireless admin panel at 192.168.1.240 with a strong, unique password to prevent unauthorized access from within your network.

What other IP addresses are related to 192.168.1.240?

192.168.1.240 belongs to the 192.168.1.0/24 subnet. Other notable IPs in this range include 192.168.1.1 (the most common home router gateway), 192.168.1.254 (used by some ISP-provided modems), and various DHCP-assigned addresses like 192.168.1.100–192.168.1.200. For different subnets, see also 192.168.0.1, 192.168.2.1, and 10.0.0.1.

How do I update the firmware on my Amped Wireless device via 192.168.1.240?

Log in to your Amped Wireless admin panel at http://192.168.1.240, then navigate to More Settings > Management > Firmware Update. You can check for updates automatically or manually upload a firmware file downloaded from the official Amped Wireless website. Keeping your firmware up to date is important for security patches and performance improvements.