192.168.1.230 Admin Login

192.168.1.230 is a private Class C IPv4 address used by select router manufacturers as their default gateway IP. Brands confirmed to use this address include Allied Telesis (notably the AT-TQ2403 wireless access point), Corega, and Hawking. If you own one of these devices, typing 192.168.1.230 into your browser's address bar will bring up the router's admin login panel. This address sits within the 192.168.1.0/24 subnet — one of the most widely used private IP ranges in home and small-office networking. Other common default gateways in this subnet include 192.168.1.254 and the widely known 192.168.1.1. Because 192.168.1.230 is a private address, it is not routable on the public internet and is exclusively used for local network management.

How to Access 192.168.1.230

To reach your router's admin panel at 192.168.1.230, follow these steps:

1. Connect your computer or laptop to the router — either via an Ethernet cable (recommended) or over Wi-Fi. A wired connection is preferred because it prevents you from being dropped mid-session when saving changes.
2. Open any web browser — Chrome, Firefox, Edge, or Safari all work fine.
3. Type http://192.168.1.230 directly into the address bar (not the search bar) and press Enter.
4. A login page will appear. Enter the default username and password for your device (see the credentials table below).
5. Once logged in, you can configure your wireless settings, change your Wi-Fi password, update firmware, set up port forwarding, and more.

If you are using an Allied Telesis AT-TQ2403, the default credentials are username: manager and password: friend. For Corega devices using this IP, try leaving the username blank and entering root as the password. Always check the label on the bottom or back of your device for the exact factory credentials printed by the manufacturer.

If You Can't Access 192.168.1.230

If entering http://192.168.1.230 in your browser doesn't load a login page, there are a few likely reasons and fixes:

• Wrong gateway IP: Your router may use a different default IP. Open the Command Prompt on Windows (Start > type cmd > press Enter) and run ipconfig /all. Look for the Default Gateway value — that is your router's actual IP address. On Mac, go to System Settings > Network > your connection > Details, and check the Router field. Common alternatives in the same subnet include 192.168.1.254 and 192.168.1.1.
• Not connected to the right network: Make sure your device is connected to the router whose IP is 192.168.1.230 — not a neighbor's network or a mobile hotspot.
• IP address was changed: A previous administrator may have changed the default gateway from 192.168.1.230 to something else. In this case, use the ipconfig /all method above to find the current gateway.
• Browser issue: Make sure you are typing the address into the address bar, not the search bar. Also try disabling any browser extensions or VPNs that might interfere.
• Firewall or security software: Temporarily disable any firewall or antivirus software that might be blocking local network access.

If none of the above resolves the issue, a factory reset (see below) will restore 192.168.1.230 as the default gateway on supported devices.

Default Login Credentials for 192.168.1.230

The table below lists the known default usernames and passwords for router brands that use 192.168.1.230 as their default gateway. Always change these credentials after your first login to protect your network from unauthorized access.

Note: If none of the above credentials work, the password may have been changed by a previous user. In that case, you will need to perform a factory reset to restore the default login for 192.168.1.230.

Changing Your Router's Password at 192.168.1.230

Keeping the factory default password on your router is a serious security risk. Default credentials like manager/friend (Allied Telesis) or admin/admin are publicly known and can be exploited by anyone who gains access to your network. Here's how to change your router's admin password once you're logged in at 192.168.1.230:

1. Log in to the admin panel at http://192.168.1.230 using your current credentials.
2. Navigate to the Administration, System, or Management section — the exact label varies by brand and firmware.
3. Look for a Change Password or Admin Password option.
4. Enter your current password, then type your new password twice to confirm.
5. Click Save or Apply. Your router may log you out and ask you to log back in with the new password.

Choose a strong password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Do not reuse your Wi-Fi password as your admin password — these should always be different for maximum security.

Router Username and Password List

Factory Reset for Routers Using 192.168.1.230

If you've forgotten your admin password or can no longer access the panel at 192.168.1.230, a factory reset is your best option. This will erase all custom settings and restore the router to its original factory state — including restoring 192.168.1.230 as the default gateway and resetting the login credentials to their defaults.

Allied Telesis AT-TQ2403 Factory Reset

1. Make sure the Allied Telesis AT-TQ2403 is powered on.
2. Locate the small Reset button on the device — it is typically recessed in a tiny hole to prevent accidental resets.
3. Insert a straightened paperclip or a similar thin object into the reset hole and hold the button for approximately 15 seconds until all indicator lights begin flashing.
4. Release the button. The device will reboot automatically.
5. Once it restarts, navigate to http://192.168.1.230 and log in with the default credentials: username: manager, password: friend.

Corega Router Factory Reset

1. With the router powered on, locate the Reset button (usually on the back or bottom panel).
2. Press and hold the reset button for 10–15 seconds using a pin or paperclip.
3. Release when the power LED flashes or changes behavior, indicating the reset is in progress.
4. Wait for the router to fully reboot, then access the admin panel at 192.168.1.230 with the default credentials (username: blank, password: root).

Important: A factory reset will erase your Wi-Fi name (SSID), Wi-Fi password, port forwarding rules, and all other custom configurations. Make sure to back up your settings before performing a reset if your router supports it.

What Is 192.168.1.230? Understanding This Private IP Address

192.168.1.230 is a Class C private IPv4 address that falls within the reserved private IP range of 192.168.0.0 – 192.168.255.255, as defined by RFC 1918. This means it is not accessible from the public internet and is exclusively used within local area networks (LANs) — such as your home Wi-Fi or a small office network.

As a private IP, 192.168.1.230 can be used in two ways:

• As a default gateway (router IP): Manufacturers like Allied Telesis and Corega assign 192.168.1.230 as the router's own address, making it the entry point for the admin panel.
• As a DHCP-assigned client IP: Your router's DHCP server may automatically assign 192.168.1.230 to a device on your network (such as a laptop, smartphone, or smart TV) if it falls within the configured DHCP range.

The 192.168.1.0/24 subnet supports up to 254 usable host addresses (192.168.1.1 through 192.168.1.254). The address 192.168.1.230 sits toward the higher end of this range, which is why it is sometimes chosen as a static gateway IP — it is less likely to conflict with DHCP-assigned addresses that typically start from 192.168.1.2 or 192.168.1.100.

Other commonly used IPs in the same subnet include 192.168.1.254, which is used by brands like 2Wire, Westell, and some Motorola modems, and 192.168.1.1, which is the most popular default gateway in the world, used by Linksys, ASUS, TP-Link, Netgear, and many others. If you're unsure which IP your router uses, always check the sticker on the bottom of the device or run ipconfig /all on Windows or ip route on Linux.

Related IP Addresses in the 192.168.1.x Subnet

The 192.168.1.0/24 network contains several IP addresses that are commonly used as default gateways by various router manufacturers. If 192.168.1.230 doesn't work for your device, one of the following addresses might be your router's actual default gateway:

• 192.168.1.1 — The most widely used default gateway in the world, used by Linksys, ASUS, TP-Link, Netgear, Huawei, and many others.
• 192.168.1.254 — Used by 2Wire, Westell, Motorola, MSI, Gigabyte, and some Netopia routers.
• 192.168.0.1 — Another extremely common default gateway, used by D-Link, Netgear, Belkin, and TP-Link models.
• 192.168.2.1 — Used by Belkin, Microsoft broadband routers, and some Zoom and U.S. Robotics models.
• 192.168.8.1 — Commonly used by Huawei mobile Wi-Fi routers and pocket hotspots.
• 192.168.10.1 — Used by some Motorola, TRENDnet, and Repotec router models.
• 192.168.100.1 — Frequently used by cable modem gateways and some Huawei and Thomson devices.
• 10.0.0.1 — A Class A private address used by Xfinity/Comcast gateways and some Apple routers.

You can always confirm your router's actual IP by checking the Default Gateway field in your network settings or by running ipconfig /all in the Windows Command Prompt.

Frequently Asked Questions About 192.168.1.230

Which routers use 192.168.1.230 as their default IP?

The most well-documented router that uses 192.168.1.230 as its default gateway is the Allied Telesis AT-TQ2403 wireless access point. Corega routers also use this IP for approximately 17% of their models, with the remaining majority defaulting to 192.168.1.1. Hawking devices have also been associated with this address. If you're unsure whether your device uses 192.168.1.230, check the label on the bottom of your router or consult the user manual.

Why isn't 192.168.1.230 loading in my browser?

If http://192.168.1.230 doesn't load, the most common reason is that your device is not connected to the correct router, or the router's default IP has been changed. Run ipconfig /all on Windows and check the Default Gateway field to find the correct IP. Also ensure you're typing the address into the browser's address bar, not the search bar.

What are the default login credentials for 192.168.1.230?

For Allied Telesis devices (e.g., AT-TQ2403), the default credentials are username: manager and password: friend. For Corega routers using this IP, try username: (blank) and password: root. For Hawking devices, try admin / admin. If none of these work, the password may have been changed and you'll need to perform a factory reset.

Is 192.168.1.230 safe to use on my network?

Yes, 192.168.1.230 is a private IP address and is completely safe to use within your local network. It is not accessible from the public internet. However, you should always change the default admin password on any router using this IP to prevent unauthorized access from within your local network.

Can two devices on my network share the IP 192.168.1.230?

No. Just like any IP address, 192.168.1.230 must be unique within your network. If two devices are assigned the same IP — for example, if your router uses 192.168.1.230 as its gateway and your DHCP server also assigns it to a client device — an IP address conflict will occur, causing connectivity issues for both devices. Make sure your DHCP range excludes 192.168.1.230 if it is being used as a static gateway address.

How do I find my router's IP if it's not 192.168.1.230?

On Windows, open Command Prompt and type ipconfig /all — the Default Gateway value is your router's IP. On Mac, go to System Settings > Network > your active connection > Details > TCP/IP tab, and look for the Router field. On Android or iPhone, tap the Wi-Fi network you're connected to and look for the Gateway or Router field in the network details. Common alternatives to 192.168.1.230 include 192.168.1.1 and 192.168.1.254.