192.168.0.4 Admin Login

192.168.0.4 is a Class C private IPv4 address that falls within the 192.168.0.0/24 subnet range. It is most notably used by Luxul routers and networking devices as their default gateway IP address. Luxul — a brand known for professional-grade wireless networking equipment used in residential and commercial AV/IT installations — ships several of its router and access point models with 192.168.0.4 pre-configured as the default admin login address. If you own a Luxul device such as the XBR-2300, XWR-1750, XWR-600, or other models in the Luxul lineup, then 192.168.0.4 is the address you'll use to access your router's admin panel. Other common default gateways in the same subnet include 192.168.0.1 and 192.168.1.254.

How to Access 192.168.0.4

To access your router's admin panel via 192.168.0.4, follow these steps:

1. Make sure your computer or device is connected to the same network as your Luxul router — either via an Ethernet cable or over Wi-Fi.
2. Open any web browser (Chrome, Firefox, Edge, Safari, etc.).
3. Type http://192.168.0.4 directly into the address bar and press Enter.
4. A login screen will appear prompting you for a username and password.
5. For most Luxul devices, the default credentials are:
   • Username: admin
   • Password: admin
6. Click Login to enter the router's control panel.

Once inside, you can configure your Wi-Fi settings, set up port forwarding, manage connected devices, update firmware, and much more. Because 192.168.0.4 is a private IP address, it is only accessible from within your local network — it cannot be reached from the internet, which adds a layer of inherent security to your admin panel.

If You Can't Access 192.168.0.4

If typing http://192.168.0.4 into your browser doesn't bring up a login page, there are a few things you should check:

• Verify your default gateway: 192.168.0.4 may not be your router's current IP. On Windows, open Command Prompt (Start > cmd) and type ipconfig /all. Look for the Default Gateway value. On macOS or Linux, open Terminal and type netstat -nr | grep default. If the gateway shown is different from 192.168.0.4, use that address instead, or check our guide to find your router IP address.
• Check your network connection: You must be connected to the router's network (wired or wireless) before 192.168.0.4 will respond. If you're disconnected, the page will time out.
• Try a different browser: Some browser extensions or security settings can block local IP access. Try an incognito/private window or a different browser entirely.
• Disable VPN or proxy: Active VPN connections can reroute your traffic and prevent access to local IPs like 192.168.0.4. Temporarily disable any VPN before trying again.
• The IP may have been changed: A previous administrator may have changed the default gateway from 192.168.0.4 to something else. In this case, you may need to perform a factory reset to restore the original settings.

Changing Your Router's Password at 192.168.0.4

Keeping your router secured with a strong, unique password is one of the most important steps you can take to protect your home or office network. The default credentials for Luxul routers — admin/admin — are publicly known and should be changed immediately after your first login at 192.168.0.4.

To change your Luxul router's admin password:

1. Log in to your router at http://192.168.0.4 using the current credentials.
2. Navigate to the Administration or System section of the control panel.
3. Look for a Change Password or Admin Password option.
4. Enter your new password (use a mix of uppercase, lowercase, numbers, and symbols for best security).
5. Confirm the new password and click Save or Apply.

You should also change your Wi-Fi network password (WPA2/WPA3 key) from the Wireless settings section. Avoid using easily guessable passwords like your address, name, or phone number. A strong network password prevents unauthorized users from connecting to your network and potentially accessing devices on it.

Router Username and Password List

Luxul Routers and the 192.168.0.4 Default Gateway

Luxul is the primary brand associated with 192.168.0.4 as a default gateway address. Luxul specializes in professional-grade networking equipment designed for custom AV (audio/visual) and IT integrators. Their product lineup includes routers, managed switches, wireless access points, and wireless controllers — all engineered for reliable performance in demanding residential and commercial environments.

Some of the Luxul models that use or are associated with the 192.168.0.4 IP address include:

• Luxul XBR-2300 — Dual-WAN wired router
• Luxul XWR-1750 — AC1750 dual-band wireless router
• Luxul XWR-600 — N600 dual-band wireless router
• Luxul XFS-1816P — 18-port PoE+ managed switch
• Luxul XWC-1000 — Wireless controller
• Luxul XAP series — Access points (XAP-310, XAP-1200, XAP-1230, XAP-1500, XAP-1610)

For all of these devices, the default login credentials are username: admin and password: admin. It is strongly recommended that you change these defaults immediately after your first login to prevent unauthorized access to your network configuration.

How to Factory Reset a Luxul Router (192.168.0.4)

If you've forgotten your admin password or can no longer access your Luxul router at 192.168.0.4, performing a factory reset will restore all settings — including the IP address and login credentials — back to their defaults.

Method 1: Physical Reset Button

1. Make sure your Luxul router is powered on.
2. Locate the Reset button on the back or bottom of the device. It is typically a small recessed button requiring a pin, paperclip, or similar thin object to press.
3. Press and hold the Reset button for approximately 10 seconds.
4. Release the button. The router's LEDs will blink or change, indicating the reset process has begun.
5. Wait for the router to fully reboot (this may take 1–2 minutes).
6. Once rebooted, you can access the admin panel again at http://192.168.0.4 using the default credentials admin / admin.

Method 2: Web Admin Interface Reset

1. Log in to your router at 192.168.0.4.
2. Navigate to Administration > Factory Defaults or System > Restore.
3. Click Restore Factory Defaults and confirm the action.
4. The router will reboot and return to its factory state.

Important: A factory reset will erase all custom configurations, including your Wi-Fi name (SSID), passwords, port forwarding rules, and any other settings you have applied. Make sure to back up your configuration before resetting if possible.

What is 192.168.0.4? Understanding Private IP Addresses

192.168.0.4 is a Class C private IPv4 address, defined under the RFC 1918 standard for private network use. This means it is not routable on the public internet — it exists solely within your local area network (LAN). The full private range for this class is 192.168.0.0 – 192.168.255.255, and the specific /24 subnet that 192.168.0.4 belongs to is 192.168.0.0/24, which spans from 192.168.0.1 to 192.168.0.254.

When a router like a Luxul device uses 192.168.0.4 as its default gateway, it means that all devices on your network communicate with the router — and through it, with the internet — via this address. Your router acts as the traffic controller: it receives data from the internet and forwards it to the correct device on your local network using private IPs assigned by its built-in DHCP server.

Here's an example of how IP assignment works in a 192.168.0.x network where the router is at 192.168.0.4:

• Your laptop might receive 192.168.0.5
• Your smartphone might receive 192.168.0.6
• Your smart TV might receive 192.168.0.7
• Your printer might receive 192.168.0.8

These addresses are dynamically assigned by the DHCP server and may change each time a device reconnects. You can also assign static (fixed) IP addresses to specific devices through the router's admin panel at 192.168.0.4, which is useful for devices like printers, NAS drives, or security cameras that need a consistent address.

Related IP Addresses in the 192.168.0.x Subnet

The 192.168.0.0/24 subnet is one of the most widely used private network ranges in the world. While 192.168.0.4 is specifically associated with Luxul networking equipment, many other IP addresses in this same subnet are used as default gateways by other popular router brands. Here are some of the most commonly encountered related addresses:

• 192.168.0.1 — The most common default gateway in this subnet, used by brands such as TP-Link, D-Link, Netgear, and many others.
• 192.168.0.1.1 — A common mistype of 192.168.0.1, often searched by users trying to reach their router admin panel.
• 192.168.2.1 — Used by some Belkin, Cisco, and other router models as their default gateway.
• 10.0.0.1 — A Class A private IP used by some Xfinity/Comcast gateways and Apple routers.
• 192.168.100.1 — Used by some ISP-provided modems and routers, particularly in certain regions.
• 192.168.1.254 — Common default gateway for some D-Link, 2Wire, and other router models.
• 192.168.8.1 — Default gateway for Huawei routers and mobile Wi-Fi hotspot devices.
• 192.168.10.1 — Used by some Cisco and Motorola router models.

Understanding the layout of the 192.168.0.x subnet helps you troubleshoot connectivity issues, avoid IP conflicts, and better manage your network. If you're unsure which IP your router uses, always check the label on the back or bottom of the device, or use the ipconfig /all command on Windows to find your Default Gateway.

Frequently Asked Questions About 192.168.0.4

What router uses 192.168.0.4 as its default IP?

The primary brand that uses 192.168.0.4 as its default gateway is Luxul. Luxul produces professional-grade routers, access points, and switches designed for AV and IT integration environments. Models such as the XWR-1750, XWR-600, XBR-2300, and various XAP-series access points are associated with this IP address. If you have a Luxul device, navigating to http://192.168.0.4 in your browser should bring up the admin login page.

What are the default username and password for 192.168.0.4?

For Luxul routers that use 192.168.0.4, the default login credentials are username: admin and password: admin. These are factory-set defaults and should be changed immediately after your first login to protect your network from unauthorized access.

Why is 192.168.0.4 not loading in my browser?

If 192.168.0.4 isn't loading, first confirm that your device is connected to the same network as your Luxul router. Then check your Default Gateway using ipconfig /all on Windows or netstat -nr | grep default on macOS/Linux. If the gateway shown is different, your router's IP may have been changed. You may also want to disable any active VPN connections, as these can prevent access to local network addresses like 192.168.0.4.

Is 192.168.0.4 safe to use?

Yes, 192.168.0.4 is a private IP address defined under RFC 1918 and is completely safe to use within your local network. It is not accessible from the public internet, which means external users cannot directly reach your router's admin panel at this address. However, you should still protect it with a strong admin password to prevent unauthorized access from within your local network.

Can I change my router's IP from 192.168.0.4 to something else?

Yes, you can change your Luxul router's IP address from 192.168.0.4 to any other valid private IP address within the 192.168.x.x range. Log in to the admin panel at http://192.168.0.4, navigate to the LAN Settings or Network section, and update the IP address field. After saving, you'll need to use the new IP to access the admin panel going forward. Note that changing this address will also affect the DHCP range your router assigns to connected devices.

How do I reset my Luxul router back to 192.168.0.4?

If the IP address of your Luxul router has been changed and you want to restore it to 192.168.0.4, you'll need to perform a factory reset. Press and hold the physical Reset button on the back of the device for approximately 10 seconds until the LEDs blink. After the router reboots, all settings — including the default gateway IP of 192.168.0.4 and the admin credentials (admin/admin) — will be restored to factory defaults.