192.168.0.30 Admin Login

The IP address 192.168.0.30 is a Class C private IPv4 address most commonly associated with D-Link wireless bridges, access points, and gaming adapters, as well as select TRENDnet networking devices. Unlike the more widely known gateway addresses such as 192.168.0.1 or 192.168.1.254, the address 192.168.0.30 is specifically assigned as the factory default IP on a focused range of wireless networking hardware — particularly D-Link's DWL-series wireless bridges, repeaters, and gaming adapters. If your device is a D-Link DWL-G710, DWL-G810, DWL-G730AP, DGL-3420, or DWL-1750, then 192.168.0.30 is the address you need to type into your browser to reach the admin panel. TRENDnet also uses this address on certain IP camera and access point models. Because 192.168.0.30 sits within the 192.168.0.0/24 private subnet, it is completely invisible to the public internet and can only be accessed from within your local network.

How to Access 192.168.0.30

To reach the admin panel of your D-Link or TRENDnet device, open any web browser — Chrome, Firefox, Edge, or Safari — and type http://192.168.0.30 directly into the address bar. Do not type it into a search engine, as that will return search results rather than your device's login page. Press Enter and you should be presented with a login prompt.

For most D-Link devices that use 192.168.0.30 as their default IP — such as the DWL-G730AP, DWL-G710, DWL-G810, and DGL-3420 — the default credentials are:

• Username: admin
• Password: (leave blank — no password required by default)

For TRENDnet devices using 192.168.0.30, the default credentials are typically:

• Username: admin
• Password: admin

Always check the label on the bottom or back of your device first, as some units ship with a unique password printed on the sticker. Once logged in, you can configure wireless settings, change the device's IP address, update firmware, set up bridging or repeater modes, and manage security options.

Keep in mind that 192.168.0.30 is a private IP address, meaning any device on your local network could technically be assigned this address. To avoid IP conflicts, make sure no other device on your network is using 192.168.0.30 at the same time as your router or access point.

If You Can't Access 192.168.0.30

If entering http://192.168.0.30 into your browser doesn't load a login page, there are several possible reasons and solutions to try:

• Wrong default gateway: Your device may not use 192.168.0.30 as its default IP. To confirm your actual gateway, open the Command Prompt on Windows (Start > type cmd > press Enter) and run the command ipconfig /all. Look for the Default Gateway field. On macOS, go to System Settings > Network > your active connection > Details. On Linux, run ip route in the terminal. If the gateway shown is different from 192.168.0.30, use that address instead, or check our guide to find your router IP address.
• Not connected to the right network: Make sure your computer or phone is connected to the same network as the D-Link or TRENDnet device. If you're on mobile data or a different Wi-Fi network, you won't be able to reach 192.168.0.30.
• IP address was changed: A previous administrator may have changed the device's IP from 192.168.0.30 to something else. In this case, you'll need to perform a factory reset to restore the default address.
• Browser issue: Some browsers auto-redirect IP addresses to search engines. Try prefixing the address with http:// (i.e., http://192.168.0.30) or use a different browser.
• Firewall or security software: Temporarily disable any firewall or VPN software that might be blocking local network access.

If none of the above resolves the issue, a factory reset is your best option to restore 192.168.0.30 as the default IP address on your device.

Router Brands That Use 192.168.0.30

Not every router brand uses 192.168.0.30 — it is a more specialized default IP compared to the ubiquitous 192.168.0.1 or 192.168.1.254. The brands and specific models confirmed to use 192.168.0.30 as their factory default IP address are:

D-Link

D-Link is the primary brand associated with 192.168.0.30. The following D-Link models ship with this address as their default:

• D-Link DWL-G730AP — Wireless travel router/access point/client (default username: admin, default password: blank)
• D-Link DWL-G710 (Rev. B1) — Wireless repeater (default username: admin, default password: blank)
• D-Link DWL-G810 (Rev. A1) — Wireless Ethernet bridge (default username: admin, default password: blank)
• D-Link DGL-3420 — Wireless gaming adapter (default username: admin, default password: blank)
• D-Link DWL-1750 — Wireless access point (default username: admin, default password: blank)

TRENDnet

TRENDnet uses 192.168.0.30 on select IP camera and access point models. TRENDnet devices at this address typically use admin / admin as the default login credentials. Always verify against the label on your specific unit.

It is worth noting that both D-Link and TRENDnet also produce many other devices that use different default IPs such as 192.168.0.1 or 192.168.10.1. The 192.168.0.30 address is specific to the wireless bridge, repeater, and gaming adapter product lines listed above.

Router Username and Password List

Factory Reset Procedures for Devices Using 192.168.0.30

If you've forgotten your login credentials or the IP address has been changed from 192.168.0.30, a factory reset will restore all settings to their defaults. Here are the reset procedures for the main devices that use this IP:

D-Link DWL-G730AP — Factory Reset

There are two ways to reset the DWL-G730AP back to its default state with IP address 192.168.0.30:

Via the Web Interface (if you can still log in):

1. Open your browser and navigate to http://192.168.0.30.
2. Log in with username admin and leave the password field blank.
3. Click the Tools tab, then select System from the left-hand menu.
4. Click Restore under the Restore to Factory Default Settings section.
5. Confirm by clicking OK in the warning dialog. Do not power off the unit during this process.
6. Wait for the WLAN light to stop blinking — the device has been reset.

Via the Hardware Reset Button (if locked out):

1. Ensure the DWL-G730AP is powered on.
2. Insert a straightened paper clip into the small Reset hole on the back of the unit.
3. Hold the button down for 10 seconds, then release.
4. Do not remove power during the reset process.
5. The unit will reboot automatically. Once the WLAN light stabilizes, the reset is complete and 192.168.0.30 is restored as the default IP.

D-Link DWL-G810 / DWL-G710 / DGL-3420 — Factory Reset

For these D-Link bridge and gaming adapter models, the hardware reset procedure is similar:

1. Keep the device powered on.
2. Locate the Reset button (usually a pinhole on the back or bottom panel).
3. Use a pin or paper clip to press and hold the Reset button for 10 seconds.
4. Release and allow the device to reboot. The default IP 192.168.0.30 will be restored along with the default username admin and a blank password.

TRENDnet Devices — Factory Reset

For TRENDnet devices using 192.168.0.30:

1. With the device powered on, locate the Reset button on the back panel.
2. Press and hold for approximately 15 seconds.
3. Release and wait for the device to reboot. The IP address will revert to 192.168.0.30 and credentials will reset to admin / admin.

Important: A factory reset erases all custom configurations — including your Wi-Fi name, password, port forwarding rules, and any static IP assignments. Only perform a reset if you are prepared to reconfigure the device from scratch.

Changing Your Password on a 192.168.0.30 Device

The default password on D-Link devices using 192.168.0.30 is blank — meaning there is no password set at all. This is a significant security risk, especially if your device is a wireless access point or bridge that is broadcasting a signal. Anyone connected to your network could access the admin panel at 192.168.0.30 without any credentials. You should set a strong password immediately after your first login.

To change your password on a D-Link device at 192.168.0.30:

1. Log in at http://192.168.0.30 using username admin and a blank password.
2. Navigate to the Tools or Admin tab in the top navigation menu.
3. Look for the Administrator Settings or Password section.
4. Enter your new password in the New Password field and confirm it in the Confirm Password field.
5. Click Apply or Save to store the new password.

For TRENDnet devices at 192.168.0.30, the process is similar — log in with admin / admin, then navigate to the Administration or Management section to update your credentials.

Choose a password that is at least 12 characters long and includes a mix of uppercase letters, lowercase letters, numbers, and symbols. Avoid using easily guessable information like your address or birthday.

What Is 192.168.0.30 as a Private IP Address?

192.168.0.30 is a Class C private IPv4 address that falls within the reserved private range of 192.168.0.0 – 192.168.255.255, as defined by RFC 1918. This means it is never routable on the public internet — it exists only within your local area network (LAN). No matter how many homes or offices around the world use 192.168.0.30 on their networks, there is no conflict, because each instance is isolated within its own private network.

In the context of D-Link and TRENDnet devices, 192.168.0.30 serves as the device management IP — the address you use to reach the web-based configuration interface. It is not always the network's default gateway (that role is typically played by your main router at an address like 192.168.0.1). Instead, 192.168.0.30 is the static IP assigned to the bridge, repeater, or access point itself so you can always find and configure it.

Within the 192.168.0.0/24 subnet, the address 192.168.0.30 is one of 254 usable host addresses (192.168.0.1 through 192.168.0.254). The subnet mask for this range is 255.255.255.0. Other devices on the same network — laptops, phones, smart TVs, printers — will each receive their own unique IP within this range, typically assigned automatically by your router's DHCP server.

Related IP addresses in the same subnet that are also commonly used as default device IPs include:

• 192.168.0.1 — The most common default gateway for routers from brands like Netgear, D-Link (main routers), and TP-Link
• 192.168.2.1 — Used by some Belkin and SMC routers as a default gateway
• 192.168.1.254 — Default gateway for BT Home Hubs, some Netgear and Thomson models
• 192.168.100.1 — Used by some cable modems and ISP-provided gateways
• 10.0.0.1 — Default gateway for some Xfinity/Comcast gateways and older Belkin routers

Frequently Asked Questions About 192.168.0.30

What devices use 192.168.0.30 as their default IP?

The devices most commonly associated with 192.168.0.30 are D-Link wireless bridges, repeaters, and gaming adapters — specifically the DWL-G730AP, DWL-G710, DWL-G810, DGL-3420, and DWL-1750. TRENDnet also uses 192.168.0.30 on certain IP cameras and access point models. If you own one of these devices and need to access its settings, navigate to http://192.168.0.30 in your browser.

What is the default username and password for 192.168.0.30?

For D-Link devices at 192.168.0.30 (such as the DWL-G730AP and DWL-G810), the default username is admin and the default password is blank — you simply leave the password field empty and click OK. For TRENDnet devices at this address, the default credentials are typically admin / admin. Always check the label on your device for model-specific credentials.

Why is 192.168.0.30 not loading in my browser?

If 192.168.0.30 isn't loading, first confirm that your computer is connected to the same network as the D-Link or TRENDnet device. Then verify that 192.168.0.30 is actually the device's current IP — run ipconfig /all on Windows or check your router's connected devices list. If the IP was changed, you'll need to perform a factory reset to restore 192.168.0.30 as the default. Also make sure you're typing http://192.168.0.30 (not https://) directly into the address bar, not a search engine.

Can I change the IP address from 192.168.0.30 to something else?

Yes. Once logged into the admin panel at 192.168.0.30, navigate to the LAN or Network Settings section. You'll find an IP Address field where you can enter a new static IP for the device. After saving, the device will reboot and you'll need to use the new IP address to access the admin panel. Make sure the new IP is within your network's subnet range and not already in use by another device.

Is 192.168.0.30 the same as my router's gateway?

Not necessarily. On networks where a D-Link DWL-series device uses 192.168.0.30, your main router's gateway is likely at a different address — most commonly 192.168.0.1. The address 192.168.0.30 is the management IP of the bridge or access point, not the gateway through which your internet traffic flows. Your main router handles internet routing; the device at 192.168.0.30 handles wireless bridging or repeating functions.

How do I find my router's IP address if it's not 192.168.0.30?

If 192.168.0.30 doesn't work for your device, you can find your actual gateway IP by opening a Command Prompt on Windows and typing ipconfig /all, then looking for the Default Gateway value. On macOS, go to System Settings > Network > your connection > Details. Common alternative addresses include 192.168.0.1, 192.168.8.1, and 192.168.10.1.

Will a factory reset on my D-Link device restore 192.168.0.30?

Yes. Performing a factory reset on any D-Link DWL-series device or TRENDnet device that originally shipped with 192.168.0.30 will restore that address as the default IP. It will also reset the username to admin and clear the password (blank for D-Link, admin for TRENDnet). Note that all custom configurations — including any Wi-Fi settings, port rules, or changed passwords — will be permanently erased by the reset.