192.168.0.112 Admin Login

192.168.0.112 is a private Class C IPv4 address that belongs to the 192.168.0.0/24 subnet — one of the most widely used private network ranges in home and small-office environments. While 192.168.0.112 is not a factory-set default gateway for any specific router brand, it is very commonly encountered as a DHCP-assigned address on networks managed by routers from Netgear, D-Link, TP-Link, and Cisco/Linksys — all of which default to the 192.168.0.x address space. On such networks, your router's actual gateway is typically 192.168.0.1, while 192.168.0.112 is dynamically or statically assigned to a connected device such as a laptop, smartphone, smart TV, printer, or IP camera. Other commonly referenced addresses in this subnet include 192.168.0.1 and 192.168.1.254.

How to Access 192.168.0.112

To access a device or admin interface at 192.168.0.112, open your preferred web browser — such as Google Chrome, Mozilla Firefox, Microsoft Edge, or Safari — and type http://192.168.0.112 directly into the address bar. Press Enter and wait for the login page to load. If the device at this address has a web-based management interface (such as a network printer, IP camera, NAS device, or a router that has been manually reconfigured to use this IP), you will be prompted to enter a username and password.

Keep in mind that you must be connected to the same local network as the device using 192.168.0.112 — either via Wi-Fi or a wired Ethernet cable — for this address to be reachable. Because 192.168.0.112 is a private IP address, it is not accessible from the public internet. It only exists and functions within your local area network (LAN). If you are trying to reach your router's admin panel specifically, your gateway is most likely 192.168.0.1 rather than 192.168.0.112, unless you or your ISP has manually changed it.

If You Can't Access 192.168.0.112

If typing http://192.168.0.112 into your browser returns an error or a blank page, there are several possible reasons and steps you can take to resolve the issue:

• Wrong IP address: The device you are trying to reach may not be using 192.168.0.112. On Windows, open the Command Prompt (Start > type cmd > press Enter) and run ipconfig /all. Look for the Default Gateway and IPv4 Address fields to confirm the correct addresses on your network.
• Not on the same network: Make sure your computer or device is connected to the same Wi-Fi or wired network as the device at 192.168.0.112. A different network or VLAN will prevent access.
• DHCP lease expired or changed: If 192.168.0.112 was dynamically assigned by your router's DHCP server, the lease may have expired and the address may now belong to a different device — or no device at all. Check your router's DHCP client list (usually found at 192.168.0.1) to see which device currently holds this address.
• Firewall or security software blocking access: Temporarily disable your firewall or antivirus software and try again. Some security tools block local network browsing.
• Device is offline: The device that was assigned 192.168.0.112 may simply be powered off or disconnected from the network. Check that the device is on and connected.

If you are looking for your router's admin panel and are unsure of the correct IP, visit our guide to find your router IP address.

What Kind of Device Uses 192.168.0.112?

Because 192.168.0.112 sits in the upper-middle range of the 192.168.0.0/24 subnet, it is most commonly assigned by a router's DHCP server to a client device on the network. Routers from Netgear, D-Link, TP-Link, and Cisco/Linksys — all of which operate in the 192.168.0.x address space — typically assign DHCP leases starting from addresses like 192.168.0.100 and going upward, which means 192.168.0.112 is a very typical address for the 12th or 13th device that connected to your network.

Devices that commonly receive an address like 192.168.0.112 include:

• Laptops and desktop computers connecting via Wi-Fi or Ethernet
• Smartphones and tablets joining your wireless network
• Smart TVs and streaming sticks (Roku, Fire TV, Apple TV)
• Network printers and scanners — which may also have their own web-based admin panel accessible at this address
• IP cameras and security systems — often configured with a static IP in this range
• NAS (Network Attached Storage) devices from brands like Synology or QNAP
• IoT smart home devices such as smart plugs, thermostats, and hubs

If you have a network printer or IP camera at 192.168.0.112, you can access its management interface by navigating to http://192.168.0.112 in your browser and logging in with the device's default credentials (usually printed on a label on the device itself).

Assigning 192.168.0.112 as a Static IP Address

By default, most devices receive their IP address automatically from the router's DHCP server, which means the address can change each time the device reconnects to the network. If you need a device to always use 192.168.0.112 — for example, a network printer, a home server, or an IP camera — you should assign it as a static (fixed) IP address. There are two ways to do this:

1. DHCP Reservation on your router: Log in to your router's admin panel (typically at 192.168.0.1 for Netgear, D-Link, TP-Link, and Cisco/Linksys routers in the 192.168.0.x range). Navigate to the DHCP or LAN settings section and look for Address Reservation or Static DHCP. Enter the device's MAC address and assign it the IP 192.168.0.112. This way, the router will always hand out the same address to that specific device.
2. Manual static IP on the device itself: On the device (e.g., a Windows PC), go to Network Settings > Adapter Properties > IPv4 Settings and manually enter:
   • IP Address: 192.168.0.112
   • Subnet Mask: 255.255.255.0
   • Default Gateway: 192.168.0.1
   • DNS Server: 8.8.8.8 (Google) or 1.1.1.1 (Cloudflare)

Before assigning 192.168.0.112 as a static address, always verify that no other device on your network is already using it. An IP address conflict — where two devices share the same IP — will cause both devices to lose network connectivity. You can check your router's DHCP client list to confirm the address is free.

Changing Your Router's Password on a 192.168.0.x Network

If your network operates in the 192.168.0.x range — meaning your router's gateway is 192.168.0.1 and devices like 192.168.0.112 are assigned by DHCP — it is critical that you secure your router with a strong admin password. Many routers from Netgear, D-Link, TP-Link, and Cisco/Linksys ship with weak or well-known default credentials that are publicly listed online, making your network vulnerable if left unchanged.

To change your router's admin password, follow these steps:

1. Open your browser and navigate to 192.168.0.1 (or whichever gateway your network uses).
2. Log in with your current admin credentials. If you haven't changed them, check the sticker on the back or bottom of your router for the default username and password.
3. Once logged in, navigate to the Administration, System, or Management section — the exact label varies by brand and model.
4. Find the Change Password or Admin Password option and enter a new, strong password. Use a mix of uppercase and lowercase letters, numbers, and special characters.
5. Save your changes and log back in with the new password to confirm it works.

In addition to changing the admin password, consider also changing your Wi-Fi password and disabling remote management if you don't need it. These steps will significantly improve the security of your entire 192.168.0.x network, protecting every device on it — including the one at 192.168.0.112.

Router Username and Password List

192.168.0.112 and the 192.168.0.0/24 Subnet

192.168.0.112 is part of the 192.168.0.0/24 network block, which spans all addresses from 192.168.0.0 to 192.168.0.255 — a total of 256 addresses, with 254 usable for devices (excluding the network address .0 and the broadcast address .255). This subnet is one of the most popular private IP ranges in the world, used by millions of home and small-office routers.

Within this subnet, certain addresses are especially well-known and commonly used. Here are some of the most notable related IPs:

• 192.168.0.1 — The most common default gateway in this subnet, used by Netgear, D-Link, TP-Link, and Cisco/Linksys routers as their factory default admin IP.
• 192.168.1.254 — Another widely used default gateway, particularly by some ISP-provided modem-routers.
• 10.0.0.1 — A default gateway used in the separate 10.0.0.0/8 private range, common in Apple and some Xfinity routers.
• 192.168.0.100–192.168.0.150 — The typical DHCP lease range on 192.168.0.x networks, where 192.168.0.112 most commonly appears.

The subnet mask for the 192.168.0.0/24 network is 255.255.255.0, meaning the first three octets (192.168.0) identify the network, and the last octet (112, in this case) identifies the specific host or device. All devices on this subnet can communicate directly with each other without needing to pass through a router, making local services — like a printer at 192.168.0.112 — instantly accessible to all connected devices.

Frequently Asked Questions About 192.168.0.112

Is 192.168.0.112 a router's default gateway?

No. 192.168.0.112 is not a factory-set default gateway for any major router brand. The default gateway on 192.168.0.x networks is almost always 192.168.0.1. The address 192.168.0.112 is typically a DHCP-assigned address given to a client device — such as a laptop, phone, or smart TV — by your router. However, it can be manually configured as a static IP for any device on the network, including a router that has been reconfigured.

Which router brands operate in the 192.168.0.x range?

The most common brands that use the 192.168.0.x subnet (with 192.168.0.1 as the gateway) include Netgear, D-Link, TP-Link, and Cisco/Linksys. If your device has been assigned 192.168.0.112, your router is very likely from one of these manufacturers. You can confirm by checking the Default Gateway field in your network settings — if it shows 192.168.0.1, your router is operating in this subnet.

Can two devices share the IP address 192.168.0.112?

No. Every device on a network must have a unique IP address. If two devices are both assigned 192.168.0.112 — whether through a DHCP error or manual misconfiguration — an IP address conflict will occur, causing both devices to lose network connectivity. Your router's DHCP server is designed to prevent this automatically, but conflicts can still happen if you manually assign static IPs without checking the DHCP lease table first.

How do I find out which device is using 192.168.0.112 on my network?

Log in to your router's admin panel at 192.168.0.1 using your admin credentials. Navigate to the DHCP Client List, Connected Devices, or LAN section (the exact name depends on your router brand — Netgear calls it Attached Devices, D-Link calls it DHCP Clients List, TP-Link calls it DHCP Client List). Find the entry for 192.168.0.112 and you will see the device's hostname and MAC address, which will help you identify it.

Is 192.168.0.112 safe to use on my network?

Yes. 192.168.0.112 is a completely safe, standard private IP address defined by RFC 1918. It cannot be routed over the public internet, meaning it is invisible and inaccessible to anyone outside your local network. The only security concern would be if an unauthorized device on your local network were using this address — which is why it's important to secure your Wi-Fi with a strong password and regularly review the connected devices list in your router's admin panel at 192.168.0.1.

How do I reset my router if I can't access 192.168.0.1 from a 192.168.0.112 device?

If you are connected to your network and your device has been assigned 192.168.0.112 but you cannot reach the router admin panel at 192.168.0.1, you may need to perform a factory reset on your router. Locate the small Reset button on the back or bottom of your router (Netgear, D-Link, TP-Link, and Cisco/Linksys all have one). Use a paperclip or pin to press and hold the button for 10–30 seconds until the router's lights flash or change, indicating a reset. The router will reboot with factory default settings, restoring the gateway to 192.168.0.1 and the admin credentials to the defaults printed on the device label.